Resource for buying your own socks and liners?
#1
LBKA (formerly punkncat)
Thread Starter
Join Date: Jan 2010
Location: Jawja
Posts: 4,299
Bikes: Spec Roubaix SL4, GT Traffic 1.0
Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 2208 Post(s)
Liked 960 Times
in
686 Posts
Resource for buying your own socks and liners?
Does anyone know of a reputable online source for socks and or locking liners?
I would like an online shop or supply I could source single, three, and five/six ply socks and who may carry a specific liner based on the "part number". I have found some pretty similar items searching diabetic needs but nothing specific to prosthesis aside from the supplies to actually pour and make your own liners. That was designed for the prop and special effect industry but was the same stuff even down to the pin umbrellas. Seeing as how I am not trained in such arts, I would rather buy it outright.
I would like an online shop or supply I could source single, three, and five/six ply socks and who may carry a specific liner based on the "part number". I have found some pretty similar items searching diabetic needs but nothing specific to prosthesis aside from the supplies to actually pour and make your own liners. That was designed for the prop and special effect industry but was the same stuff even down to the pin umbrellas. Seeing as how I am not trained in such arts, I would rather buy it outright.
#2
Full Member
www.amputeesupply.com has some items. I have not used them, but they have answered a couple of questions for me.
Their selection is a bit limited.
Their selection is a bit limited.
#3
LBKA (formerly punkncat)
Thread Starter
Join Date: Jan 2010
Location: Jawja
Posts: 4,299
Bikes: Spec Roubaix SL4, GT Traffic 1.0
Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 2208 Post(s)
Liked 960 Times
in
686 Posts
Thanks for the link, but I agree...they are limited, and pricey. I was hoping to find a source where I can find these items for less than they are available at my doctor's office.
#5
Newbie
Join Date: Mar 2015
Posts: 1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Hi everyone,
[COLOR=#000000]I haven't been on a bike in years and I'm hoping somebody can help. I'm a BK Amp, and when I get on a bike, my prosthetic leg angles outward about 45deg at the toe.
_____________
PMP
[COLOR=#000000]I haven't been on a bike in years and I'm hoping somebody can help. I'm a BK Amp, and when I get on a bike, my prosthetic leg angles outward about 45deg at the toe.
_____________
PMP
Last edited by Metora06; 12-15-15 at 06:13 AM.
#6
LBKA (formerly punkncat)
Thread Starter
Join Date: Jan 2010
Location: Jawja
Posts: 4,299
Bikes: Spec Roubaix SL4, GT Traffic 1.0
Mentioned: 17 Post(s)
Tagged: 0 Thread(s)
Quoted: 2208 Post(s)
Liked 960 Times
in
686 Posts
There are a couple of ways to address this. Most commonly what I do is use an older, looser fitting leg, and turn the foot "toed in" to avoid hitting the heel on the crank arm. Another method is to use pedal extenders to push past where your heel would strike with pedal placement. One other that some have used is creating a pylon only foot for use on the bike. There is some reading concerning this in various posts here....and welcome.
#7
Junior Member
Join Date: Apr 2014
Location: Poughkeepsie, New York
Posts: 20
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I had the same problem and here's what I did.
Added a pedal extender and pedals with toe cages. I also had my foot angled in just a little bit, but enough to make a difference without affecting my gait. I would suggest that if you go that route that you get smooth pedals and not the ones with protrusions sticking up. And don't make the toe straps too tight. If you need to get your foot off that pedal in a hurry, you want the least amount of resistance holding your foot in place. After several falls I learned to get my foot out of the toe clip way before i'm coming to a stop.
I know there must be other/better ways, but what I have works well for me.
Added a pedal extender and pedals with toe cages. I also had my foot angled in just a little bit, but enough to make a difference without affecting my gait. I would suggest that if you go that route that you get smooth pedals and not the ones with protrusions sticking up. And don't make the toe straps too tight. If you need to get your foot off that pedal in a hurry, you want the least amount of resistance holding your foot in place. After several falls I learned to get my foot out of the toe clip way before i'm coming to a stop.
I know there must be other/better ways, but what I have works well for me.