- Quick inquiry about changing 6-speed to 7-speed freewheel
- Shimano BR-M395 or Shimano BR-M445
- Sora 2013
- How to remove an extremely seized bottom bracket?
- Seatpost fit
- Mounting kickstand w/ under-chainstay RD cable
- 12 tooth cassette to 11 tooth?
- Rear D wiggles 1/8" despite being torqued correctly
- Froze my BB spindle to install thru outboard bearings. Water condensation a problem?
- Opinions or experience with this workstand?
- Adapter for 3oz Phil Wood grease for use with finish line grease gun.
- Grease on low tenson spokes of front mtn wheel
- Adjustable handlebar angle - metal teeth stripped, what to do?
- seeking 25.4 compact drop bars
- Chainline setup - is it really as simple as...
- spindle length for 1984 sugino rt crank?
- GUIDE: Repairing Shimano 600 (6400) STI Levers
- major mechanical(s)
- Why did my front derailer die such a painful death?
- White Bar Tape That Stays White
- '91 Cannondale MTB Bottom Bracket Size?
- Sprocket/Free Wheel Sway
- Options for bigger granny gear?
- Shimano 105 shifters
- SRAM GXP Bottom Bracket & Sram S100 1.1 Crankset
- broken frame
- Oddball Braze-on
- GT 29er clicking noise whilst cycling
- Bought a used bike, a couple of problems
- Stem Replacement Comparison
- Shimano Hub Maintenace
- Campagnolo Athena Shifters
- I Didn't Hit Anything, But I Got a Pinch Flat
- Nishiki 3-speed conversion advice
- nexus gear cable housing?
- Integrated shifters don't mix with randonneur bars? Compact bars the solution?
- Deformed crank thread
- Changing fit, change stem extension
- Is this the tool you use when demolishing your bottom bracket?
- I think I trashed my front tire today
- How easy/difficult is it to install a zero stack or integral headset?
- I'm going crazy. Please help. Headsets are hurting my head
- Breaking chain at same pin previously broken
- Seeking Advice on Upgrading Forks
- Is is possible to replace a broken lever on Hayes Dyno Sport brakes?
- Asking for advice
- Sticky Look Keo Blade 12's
- Suntour XCR-LO suspension w/ only 34mm travel?
- Shifter not Working Properly
- Freewheel on a phil wood fixed hub?
- Mysterious ticking/creaking seatpost: Why?
- Carbon Fiber Frame Repair
- 2009 Fantom Cross Outlaw Seatpost Clamp Torque Spec
- tires on & off using tire levers
- Shifting is rough after removing rear wheel
- Patching a Tire?
- Softest Brake Pad?
- Please help! Component advice, newbie repairing 80s tourer
- Bottom bracket question
- i need your help or advice can you help??
- Single-Speed question
- Sideways tension on Nuovo Recoird rear derailleur
- Vintage bike seats: why do they start changing pitch when sat on?
- question about converting a roadbike to more upright bars
- Headset, wheel, stem misalignment - ?
- Water inside innertube?
- What about rear axle set screw adjusters???
- What kind of tool investment am I looking at?
- 28h 2 cross lacing
- Specialized Myka MTB Brakes Wrong Way Round In US?
- Dialing in a Shimano 10-speed RD
- Fitting a 105 chainset on a 2008 Trek Madone 4.7
- Shoe Stretching
- How to Remove Shimano Downtube Shifter
- Campagnolo Compact
- dura Ace Di2 10 speed on the new Orbea Ordu 2013
- Measuring a bike
- Crank squeaking like a door.
- Brooks saddle tension variations
- Handlebar center diameter pros and cons
- Adjusting brake cables on my '74 Schwinn Continental
- Tandem timing chain math
- This is nothing like working on a car
- Angled Headset Spacer
- bicycle books
- Hole in Trek 520 frame
- replacing old BB with asymmetric spindle with sealed cartridge type
- Overhaul Mavic Aksium free hub?
- flower food ok for rust removal?
- would flowering plant food work for rust removal?
- Is it still safe to ride ?
- Replace Jockey Puilley on RD?
- Peugeot BB question.
- Trouble getting a left crank arm off.
- Qualified IGH Repair shops Northeast US
- wd40bike
- Really hard grip shifts. Cables?
- What happened to this hub locknut?
- Shift housing length for older Shimano STI levers
- Heads down spokes: leading or trailing?