Bicycle Mechanics [Archive] - Page 587

Old frame for a fixie; what am I looking at here?
Campy ergo lever triple to double compatibility - Daytona circa 2005
7- --> 8-speed question/opinion
shimano 105 9 speed triple crank on deore xt 8 speed drivetrain---???
Rear deraillieur tension pulley popping
Replacing individual cogs on a casserre
Help removing old crank
New front brake cable feels (and sounds) like a zipper
Can't tighten OR loosen my stem/bar bolt.
Carbon or aluminum steerer on carbon fork?
1984 Peugeot UO-14
9 speed to 10 speed conversion
Tools.......buy as you need, or get a 'kit'?
Help, with hubs....
External bottom bracket <--> cranks
Rear Axle Type: 10x1
Converting Road pads for Cantis
storing tools and parts without drawers or pegbboard
Problem: replacement triple crank too close to frame?
Road Caliper Brakes on MTB bridge
7-speed cass on 8/9 speed wheel on old Raleigh
Steerer length rule of thumb?
upholstering a saddle
I need help fine tuning my front derailleur
Old school stem, new school handlebar
Bottom Bracket Replacement
Sealed Bearing Hub Rusted Stuck
What books are you reading/have you read that you found informative?
Substituting a 34 in place of a 36 tooth middle chainring on a MTB
Look Keo axle/bearing problems
is this wheel unrepairable? Mavic Cosmic
seat keeps slipping down roughly half an inch
44T front derailleur with 48T (M771 MTB)
what size pin spanner?
Sluggish cassette up shift
Problem: jammed BBB Roundhead extender
Is Shimano 9 speed jockey wheels OK with eight speed drivetrain.
Are spacers above the stem necessary?
Bottom Bracket came loose?
Front derailleur issue
Campy help! Need to replace cone in 8 speed Chorus rear hub- part availablity?
Pedaling won't move the tires.
crankset help... stripped female threads for grannie ring
New V-Brakes - Is vertical alignment a rule of thumb or a functional issue?
modifying a rear mountain bike hub
switching pedals and brakes on a ''CX'' bike
Rear brake makes a "thump" 1x per revolution
Reasonably Accurate Low End Vernier Calipers?
New bike!!!
Ultegra Crankset
Headset Choice
Brifter dead?
Shimano 6700 vs 6701 chain?
Replacing Bearings in Campagnolo Cartridge BB
Can I mount a brake here?
Correct BB for Ultegra SL 6600 cranks going into Defy Advanced frame?
Two specialized city bikes (Hard rock & Rockhopper) canti-lever issues.
Axle mounted kickstand instructions
Brake and drivetrain issues?
1978 Campagnolo New Record Crank Spindle Replacement
crankset recommendation
Schwinn Seatpost Question
Shimano 3 speed coaster hub cable replacement.
SRAM Quick Link & DA 9 sp Chain
What size FD?
The pedals fell off my bike - not how you think; please help
I meant what size FD clamp?
Ultegra 6600 short cage RD on a 34/50 -11/28 setup
Fork rake questions
Convert my Kestrel threaded 1" quill stem to threadless
Convert Octalink V1 to Hollowtech II for a Dura-Ace 7900 crank
Bottom Bracket Replacement on Trek Soho S
Crank length 170mm, 172.5mm, 175mm
Cassette options
Pedro's or Park Cable Cutter?
Single speed question
Giante Revive
Where do I start?
Centering cheap cantilever brakes?
Cone compatiability in old Formula (MTB) Hubs from 90s
new wheels, chain slipping on cassette?
Cranks spin forward without catching and chain not moving
Powertap head won't find hub after firmware upgrade
Built to fail?
Trashed Front Derailer
Teflon Tape vs. Grease on Threads
Tire problem - What do you think caused it?
Revised Campy Khamsin 2011 wheelset?
Threaded to Threadless Fork Steerer Length?
Which headsets fit a Cannondale Trail SL 5 ?
Campy BB30 Adapter Question
Cone Conundrum Continues, advice needed!!!
Rust removal techniques
Shimano RD puley, bushings vs. sealed bearings. Are different models interchangeable?
SRAM S7 push rod lenght ?
Disc rim with V-brakes?
Gear slipping
Do Shimano 7801 chain pins work with 7900 chains?
Can I lace a 24h to a 32h hub?
Not in love with Campy brake setup, please help!