- Portland, OR aluminum frame repair needed.
- How Many Degrees Will a HT Lug Bend Answered
- Snapped off top tube cable guide
- Bending Head Lug Ideas Needed
- Free frame jigs
- Tank Swap and Ready to Braze
- Steel fork repair
- Cromoly vs Reynolds 725
- How many bottle cage mounts are too many on a down tube?
- 531 stays vs. RC2
- Santana Finish question
- Matching Chain Stay Length to Trail
- My Beginner Questions
- Cleaning flux/pickle
- Walty Geometry
- Old Henry James Frame fixture manual?
- Retrofitting Added Functionality to an existing frame
- Getting the most out of propane with multi-port tips
- FS Two Custom Frames
- Bottom Bracket Bending Rods
- Would you ride this frame?
- Fat-/Cruiserbike Frame for Cargobike build
- Damping Fork Vibrations
- .1mm makes a difference
- Curious about this frame
- 8-5-8 Downtube?
- Source for Drilled Eyelets
- Can someone explain?
- Source for tubing scraps?
- 531 tubes and nervex lugs in C&V for sale (PSA..not mine)
- Small down tube bulge- danger?
- A learning curve question!
- Can Aluminium Frames Be Damaged By Hail?
- Am I screwed? Or is it all OK?
- Re-threading a RD hanger?
- Advice on crack in seatstay/brake bridge
- Ill leave this Here
- Attaching lugs to BB shells
- Rack tubing?
- Questions about Custom Made Bicycles (2019)
- WTB VAR 35mm x 1mm French BB Tap
- BB Height Question 26" Wheel
- Where to find Paterek DVDs?
- Seat stay caps
- ID frame based on lugs?
- FS Fork Jig
- Which clear coat over which spray paint?
- Premium Steels — How Much Have They Changed Since the 1990s?
- Lugged bottom bracket for 28.6 seat tube and 34.9 down tube
- Adjusting a frameset to 650B Geometry Question
- some wild frame geometry
- Aluminum tubes and components
- 1970's Mondia repair
- Geometry Measuring Device
- Replacing Down Tube
- Question about un-brazing
- Choosing a builder?
- Lug angle question/help
- Good short vid on silver brazing
- Chromed lugs?
- For Sale- Good OA torch for building
- Road Bike Tube Recommendations?
- Cleaning flux from inside stays
- Acceptable Rigid Fork replacement for 26" 100mm Suspension Fork
- Off topic but WTH Question: First time stick welding setup?
- Tube recommendations for stiff touring/commuting bike
- Rear dropouts that put the chainstay below the rear axle?
- frame geometry question concerning down tube angle
- Frame building jigs for sale
- How to hold tubes together for fillet brazing without a jig
- What downside is there to more bottom bracket drop?
- Making your own caps
- Bottle Bosses Center of Down Tube
- What is the benefit of a Pursuit frame?
- Where to find longer tubing??
- Longest available chainstays?
- Vert to horizontal dropouts
- HJ Universal Jig Mod
- technical article on the strength of various titanium alloys when welded
- New frame thread grief
- Best way to clean tubes and prevent rust
- Consumer Product Safety Commission
- Adhesive and a cable stop
- Old Tools - any good?
- Geometry gurus ?
- Haden Lug catalogue - free - anyone want it?
- Frame fixed, painted and rides as I remember it
- Keeping bosses straight
- General tubing thickness
- What would you do about this?
- QR-Through Axle Conversion
- Next Step is the Frame
- Pump attachment
- Reaming a 44mm head tube
- Fork deflection
- Fixing a Fixie,back to a road bike Guerciotti
- Brazing; Minimal paint removal for repair?
- Dented Seatstay, Repair?
- Effect of Butt Length
- Best Air+Propane/MAPP gas torch?