PDA

View Full Version : Framebuilders


Pages : 1 2 3 4 5 6 7 8 9 10 11 12 13 [14] 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

  1. customizing an aluminum frame
  2. experienced framebuilders: need some help on road fixed gear bicycle geometry
  3. Carbon Frame Repair?
  4. Ok guys, how do i fix this at home??
  5. Is there a framebuilder near Louisville KY?
  6. Internally routed disc brake cables
  7. Such a thing as CR-MO aluminum?? Nashbar says so
  8. Framebuilder database
  9. I'm interested in your opinion please (nashbar cyclocross frame)
  10. Do I need to wet sand the base coat before I clear?
  11. Old steel frame conversion to ISP type
  12. Force Analysis Software
  13. First frame repair
  14. How to measure the rake of a fork
  15. Mixte Lug-sets for sale
  16. Deraileur tab position
  17. Some basics (stupid questions)
  18. Seat Stay and Drop out repair
  19. Oregon Handmade Bicycle Show
  20. filing lugs / shaving off parts
  21. Books on framebuilding/frame geometry
  22. How bad is this seatpost crack and what can be done? (Columbus Thermachrom steel)
  23. Frame Jig
  24. Minor Frame Repiar
  25. Non-round Seat Tube
  26. Bamboo question..
  27. Baked bamboo smells good.
  28. fastmetal
  29. Is this material appropriate
  30. cracks in head tube of Electra Aluminum frame
  31. Advised to re-post this in here:
  32. Looking for a special seatbinder... help
  33. Building my own frame
  34. Have I gone insane?
  35. Opinions about Serotta Classique and Lynskey Sportive
  36. Oxy-Acetylene Torch compatibility with Bernzomatic Oxy-Max Power Propylene cylinders
  37. Metallurgy 6061 vs 7005?? Pros and Cons of these 2 Frames on sale Thanks
  38. Is my frame seriously damaged?
  39. Looking for input... again.
  40. Mountain bike head tube
  41. Drilling holes in a frame
  42. Building a recumbent kit
  43. Double top tube cures shimmy?
  44. Silver prices
  45. Torches...
  46. Best way to remove brake cable mounts?
  47. Bruni - 26" Wheels
  48. Did I screw up by reheating dropout too many times??? Help
  49. What torch?
  50. Alternatives to paint/powder? Gun bluing?
  51. "Space-frame" bikes
  52. Cost of adding braze-ons/bosses
  53. rear suspension for VOTEC M6 frame
  54. Do I need reinforcements for h20 bosses?
  55. Halp!
  56. frame building help needed please.
  57. Front end impact damage looking for advice
  58. New bike leans to right with no hands on bar
  59. Filing out front fork-end
  60. Finally bit the bullet
  61. Titanium Forks
  62. Bike size
  63. Headset bearing loads
  64. New Steel for Bicycle Frames?
  65. A tour of Folk Engineered frame builders in Newark, NJ, Sunday, June 12, 2011 (fb)
  66. Filing lugs, 30 years after assembly
  67. Can I use stay-brite for small braze ons?
  68. Frances Bikes
  69. Seatpost + Bottle mount dilemma
  70. A few new touring builds
  71. Pre braze tube deflection
  72. 1 inch conduit bender to bend frok stays??
  73. Dimensions of downtubes on step through frames
  74. JB Weld Strong Enough for Braze-ons?
  75. Double canti post?
  76. Powder coat - metallic brown or metallic green??
  77. Stainless Steel frame?
  78. Would a local auto body shop do frame powdercoating?
  79. Bottom Bracket Fixturing
  80. Is this dropout joint going to fail?
  81. How to polish Ti.
  82. Rear drop out to have a Bob attachment AND Rohloff rear hub??
  83. Can this fork be fixed?
  84. How To Tell If a Frqame Is a Good Frame?
  85. Beware of the Desperado
  86. Mitsugi fork crowns availability?
  87. Monostay seat tube join
  88. A variation on a pedal
  89. frame make over
  90. copper bike?
  91. Columbus SPS track tubeset - $100
  92. Touring frame design help
  93. Road Bike Geometries
  94. Odd Tange Tubing Decal
  95. Welding Scandium
  96. Fork Crown / steertube failure
  97. 1999 Fat Chance Yo Eddy Correct Axle To Crown Length
  98. Should I change frame design because of wheel availability? A 650b quandry.
  99. The Feel of Steel
  100. Hope anybody could explain me this...