PDA

View Full Version : Framebuilders



Pages : 1 [2] 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37



  1. Custom Builder Recommendation
  2. primer on Trek bonded aluminum
  3. which is better Ti?
  4. Seatstay repair on aluminium bike
  5. frame brazing start up costs... ugh
  6. Modifying the length of a steel frame
  7. Spotted in Richmond, Virginia this weekend
  8. My Custom Titanium Bike
  9. 3XXX series aluminum
  10. Frame Crack Question
  11. FS:Complete Framebuilding Setup-Vintage
  12. Too late? (chainstay vs bigger tire)
  13. New Phil Wood Hub has 222mm OLD rear spacing and 13 cog cassette
  14. Front derailleur tab position
  15. Grade of aluminum in VisionTech aero bars
  16. Is this a decent TIG setup?
  17. Bad idea to hire a welder?
  18. Can True Temper OX Plat tube sets be lugged?
  19. Twin top tubes for a mixte
  20. Un-Brazing
  21. brake seatstay mount on the backside instead of top?
  22. Peugeot Perthus 753 - cold sprung?
  23. Buying bamboo for bike building
  24. MIG Tacking fillet brazed frame?
  25. Front vs rear rack brazeons
  26. How to test the endurance of a frame?
  27. Making Lugs/Cutting
  28. HiI have have these Schwinn tools that i think hold on to the frame
  29. MTB swingarm as rear end of homebuilt folder?
  30. Number 1, finally..
  31. Will Holes for Internal Routing Compromise Frame?
  32. Bent Hanger Repair
  33. wheelbase vs front-center/rear-center
  34. Does mixing frame materials mean poor handling?
  35. Doubt about steel frame tubbing
  36. Broke Bianchi
  37. Jacobs head badge, info about brand?
  38. Front-loads and low-trail vs. wheel flop.
  39. Cannondale non-replaceable Derailleur Hanger Question
  40. Seat tube crack: braze-fill vs tube replacement
  41. What would you do?
  42. Rattle in top tube and fork leg
  43. How short of a headtube can I get away with?
  44. Frame Reinforcement?
  45. 126mm dropouts cold set to 135, opinions?
  46. Bamboo build, advice on finishing.
  47. Tube Notcher, Something Different
  48. slight "wobble" in bike while riding.
  49. RIP Tom Teesdale
  50. possible to bend an antique military badge for a headtube ?
  51. Cutting down adult lugged frames to kid size?
  52. pizza delivery bicycle
  53. Track end source help please
  54. stainless junk needed.
  55. Integrated Racks
  56. Starting a Columbus Air road bike frame build ...this could take a while!
  57. looking for some kind of protection for my eyes so I can wear my glasses
  58. Help building my first steel frame bike
  59. Bent fork, Need advice
  60. building a full suspension bike.
  61. Cracked headset on late '70's Rossin
  62. welder in Boston area?
  63. Tubing question
  64. opinions on frame geometry
  65. Amazing Time Trial Bike Project
  66. Bamboo bike - finally doing it
  67. Cracking on older Aluminum Lugs
  68. Paragon Polydrops and Cromoly Tubing
  69. Opinions on a broken fork crown lug?
  70. 1985 Miyata 610 damaged frame
  71. Enamel over Clearcoat?
  72. How to remove powder coating?
  73. Dimple the chainstays on a Ti Serotta?
  74. Rust around lugs and welding joints, possible crack on mid 80's bianchi
  75. braze-ons for caliper and disc brakes?
  76. Frame Weight Question
  77. Old 531 frame - Paint scratch? Crack?
  78. OK, I have a strange, strange info request.....
  79. Whats your favorite 4130 CroMoly tubing source?
  80. Brake mounting jig?
  81. Painting/Masking Lugs
  82. Top Tube Replacement
  83. Fiberfix tape for broken carbon??
  84. Fillet brazed head tube
  85. Bike Cult Show - NYC Hand-Built Bike Show - 8/16, 8/17
  86. VOTEC V.MA Handmade Titanium frame , help please!
  87. I've been building this
  88. What is this frame?
  89. Lugged Steel Trailer?
  90. University of Iowa Hand Built Bicycle Program
  91. Wheelbase and effect on steering
  92. Making wooden fenders
  93. Thoughts on Alloy dropout Repair/Replacement?
  94. Tool question -- cutting the seatpost slot in the seat tube
  95. custom geometry -- any problems?
  96. Does anyone here have a newer steel road bike?
  97. Tange Prestige Quality
  98. Cold setting necessary with a jig?
  99. Tandem headtube attachment design question
  100. Breadwinner or Indyfab