PDA

View Full Version : Framebuilders


Pages : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 [26] 27 28 29 30 31 32 33


  1. Rear Derailleur Cable Stop Position
  2. franken-tandem
  3. Ultra-light supercustom
  4. Magnesium frame over titanium?
  5. Is this dent worth repairing?
  6. Felt Bikes
  7. Rans gets credit for inventing Crank Forward Bikes
  8. Oxy-propane with a Smith AW1A?? any experience?
  9. A recumbent electric bike?
  10. Where is the market heading?
  11. Hope anybody could explain me this...
  12. The Feel of Steel
  13. Should I change frame design because of wheel availability? A 650b quandry.
  14. 1999 Fat Chance Yo Eddy Correct Axle To Crown Length
  15. Fork Crown / steertube failure
  16. Welding Scandium
  17. Odd Tange Tubing Decal
  18. Road Bike Geometries
  19. Touring frame design help
  20. Columbus SPS track tubeset - $100
  21. copper bike?
  22. frame make over
  23. A variation on a pedal
  24. Monostay seat tube join
  25. Mitsugi fork crowns availability?
  26. Beware of the Desperado
  27. How To Tell If a Frqame Is a Good Frame?
  28. Can this fork be fixed?
  29. Rear drop out to have a Bob attachment AND Rohloff rear hub??
  30. How to polish Ti.
  31. Is this dropout joint going to fail?
  32. Bottom Bracket Fixturing
  33. Would a local auto body shop do frame powdercoating?
  34. Stainless Steel frame?
  35. Powder coat - metallic brown or metallic green??
  36. Double canti post?
  37. JB Weld Strong Enough for Braze-ons?
  38. Dimensions of downtubes on step through frames
  39. 1 inch conduit bender to bend frok stays??
  40. Pre braze tube deflection
  41. A few new touring builds
  42. Seatpost + Bottle mount dilemma
  43. Frances Bikes
  44. Can I use stay-brite for small braze ons?
  45. Filing lugs, 30 years after assembly
  46. A tour of Folk Engineered frame builders in Newark, NJ, Sunday, June 12, 2011 (fb)
  47. New Steel for Bicycle Frames?
  48. Headset bearing loads
  49. Bike size
  50. Titanium Forks
  51. Finally bit the bullet
  52. Filing out front fork-end
  53. New bike leans to right with no hands on bar
  54. Front end impact damage looking for advice
  55. frame building help needed please.
  56. Halp!
  57. Do I need reinforcements for h20 bosses?
  58. rear suspension for VOTEC M6 frame
  59. Cost of adding braze-ons/bosses
  60. "Space-frame" bikes
  61. Alternatives to paint/powder? Gun bluing?
  62. What torch?
  63. Did I screw up by reheating dropout too many times??? Help
  64. Bruni - 26" Wheels
  65. Best way to remove brake cable mounts?
  66. Torches...
  67. Silver prices
  68. Double top tube cures shimmy?
  69. Building a recumbent kit
  70. Drilling holes in a frame
  71. Mountain bike head tube
  72. Looking for input... again.
  73. Is my frame seriously damaged?
  74. Metallurgy 6061 vs 7005?? Pros and Cons of these 2 Frames on sale Thanks
  75. Oxy-Acetylene Torch compatibility with Bernzomatic Oxy-Max Power Propylene cylinders
  76. Opinions about Serotta Classique and Lynskey Sportive
  77. Have I gone insane?
  78. Building my own frame
  79. Looking for a special seatbinder... help
  80. Advised to re-post this in here:
  81. cracks in head tube of Electra Aluminum frame
  82. Is this material appropriate
  83. fastmetal
  84. Baked bamboo smells good.
  85. Bamboo question..
  86. Non-round Seat Tube
  87. Minor Frame Repiar
  88. Frame Jig
  89. How bad is this seatpost crack and what can be done? (Columbus Thermachrom steel)
  90. Books on framebuilding/frame geometry
  91. filing lugs / shaving off parts
  92. Oregon Handmade Bicycle Show
  93. Seat Stay and Drop out repair
  94. Some basics (stupid questions)
  95. Deraileur tab position
  96. Mixte Lug-sets for sale
  97. How to measure the rake of a fork
  98. First frame repair
  99. Force Analysis Software
  100. Old steel frame conversion to ISP type