PDA

View Full Version : Framebuilders



Pages : [1] 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38



  1. Choosing steel tubes and lugs for a "Gravel Grinder" bike
  2. source for jig parts, cones etc?
  3. Patents I should be aware of when buling a frame
  4. Columbus Genius tubing for bigger frames
  5. Bamboo Mk3 - but this time not all bamboo!
  6. Frame gets weaken from shortening chain stays
  7. The Physics of Chainstay Length?
  8. Wanted: Rivet style brake cable stops
  9. 30x17 chainstays questions
  10. Need Some Advice on O/A Regulators for a Beginner's Setup
  11. Longshen series 300 lugs
  12. What do you think of this frame damage (Reynolds 531)?
  13. Sandblasting + Powdercoating - How to make sure stamped VIN on BB is still legible?
  14. aluminum bike frame.
  15. Source for "Overdrive" bottom bracket shells?
  16. Stainless steel tubing: Strength vs stiffness
  17. Dream bike
  18. TIG vs Mig welding
  19. stuck seat post thread #99,182: The oversized seat post
  20. Frames made with Timetal 15-3 or 15-3-3-3 Titanium Tubing
  21. Please direct me to information about fork design
  22. Looking for a jig
  23. Looking for a frame builder to work with
  24. Looking for a specific frame
  25. french steel tubes
  26. Mongoose Seat Post Shear off
  27. Check my geometry please
  28. Best Modern Steel Tubing For Road Bike (columbus?)
  29. Newbie questions on ultra low cost frame building for pedgens in low income countries
  30. WTB Rear Campy drop-out (short)
  31. I need help with a rear dropout.....down and out in Los Angeles
  32. Carbon Fiber Tubes for Bicycle fraem building?
  33. steerer tube die pitch threading advice required.
  34. Is there a users guide to understand the difference in Frame Tube Sets
  35. Building frames as an occupation
  36. New steel for bikes?
  37. Spray Painting Mt Bike Frame with small Compressor advice needed.
  38. Prepping for paint-Sandblasting
  39. Gloss to Matte clearcoat?
  40. Is all double-butted 4130 created equally?
  41. Welding Recommendations
  42. Suggested tubing for first lugged steel frame build
  43. Need info on manipulating Aluminum for repair
  44. fork taper fabrication question
  45. Rebrazing arrachments on a front rack.
  46. Curvy geometry vs. straight geometry
  47. Using mild steel, will the frame collapse and kill me?
  48. Mondonico frame repair?
  49. question about unique touches i found on an NJS frame
  50. VERY slow-going build in process.
  51. S and S coupled Pinion drive frame
  52. Considering purchasing a New Steel Frame & Fork, any input on their frame builders?
  53. Carefully Straightening a Steel Seat Stay that's Dented and Bent
  54. New Framebuilder Website
  55. Ti or Al lug kits?
  56. Are any carbon fiber frame builders active on this forum?
  57. Need help with CAD drawing for new frame
  58. carbon frame life cycle and longevity
  59. Couple of frame questions- 80s steel frames specifically
  60. CS bridge length and gear cable adjuster boss questions
  61. Fork fail caught (just) in time - but how to repair?
  62. Small frame step through, chromoly, internal gear hub...
  63. Zona or Spirit for everyday + light touring
  64. Bottom HT lug
  65. Any frame builders here work @ Kinesis in the mid 90's?
  66. Integrated vs. Non-integrated seatpost clamp
  67. So I'm just about to finish my '71-'72 Peugeot build and...
  68. Dropout/Chainstay Repair
  69. Frame questions
  70. Both frames are 54cm, but 2 inch difference from fork to rear drop out.
  71. Touring Frame Question
  72. Converting a 1987 Cannondale Fork From Roller To Disc
  73. somebody build a frame, willya? This place is getting silly
  74. Artisan bikebuilding
  75. Slotting cable guides?
  76. Water Bottle boss problem
  77. Bent fork with 531c tubing - Reset to proper dimensions?
  78. Early frame dimensions
  79. First road bike build
  80. Screw and Glue (Epoxy) to build a frame?
  81. NY framebuilder to add rear disc tab on steel mtn frame?
  82. Can someone school me on steel as a material for making frames?
  83. How to remove a w/b boss, on the inside of tube?
  84. Trailer wheel mounts for 9mm QR wheels
  85. Best abrasives to clean up brass from brazed frame
  86. Lugged bottom bracket shells and chainstay angle
  87. Shorting the chainstays on an aluminum/carbon frame
  88. I bought serotta... Sorta
  89. Steel Ride and flex qualities equivalent in a Titanium frame?
  90. Dropout repair (rear) opinions
  91. Framebuilder Supply: Anyone have experience with these guys?
  92. bike frame wisdom: what i got vs. the new Rivendell
  93. Hammill fork bender - 8" madrel
  94. Jig Use
  95. What I saw at NAHBS 2015
  96. Bay area beginner, just trying to see what the story is out here.
  97. Chromoly 4130 Tube Sizes???? Bending????
  98. JIGLESS kit and method
  99. Is this frame salvageable?
  100. Frame with Overhead Bar(s)