Classic & Vintage - Brake Pad Question
Bikeforums.net is a forum about nothing but bikes. Our community can help you find information about hard-to-find and localized information like bicycle tours, specialties like where in your area to have your recumbent bike serviced, or what are the best bicycle tires and seats for the activities you use your bike for.
05-29-03, 01:43 PM
I'm not sure if this belongs here or in the mechanics forum-apologies if misplaced. Here it is.
I have a 1977or 1978 Schwinn Traveler III, and I need to replace the original brake pads. The brakes are center pull (seems that dual pivot cantilever are the type). The bike is equipped with Shimano 400-10 spd. I saw something called the Dura Holder (link below) and am wondering if anyone had any experience with them or if there was a better OEM replacement solution without installation difficulties. All the brake related parts are in good shape, I just don't know what pads will work. Thanks much in advance. The second link may also be a possibility, but does anyone know if a pad holder is part of the setup? I sent a similar e-mail to the Harris Cyclery address.
Thanks much for any assistance.
05-29-03, 08:57 PM
Do you mean the brake that has one mount to the bike frame, with a pivot at each end of the arm? Cheap replacemant caliper pads will work on them and look more correct.
05-30-03, 08:18 AM
Thank you very much for the reply. Yes, I believe. The brake is attached to the frame at one point with a pivot at the end of each arm. Cheap replacement pads would be great. Would a LBS typically stock them, or do you know of an on-line source, i.e. are this size replacement pads common? I'm not sure due to age of bike and size/shape etc. of the pad.
I'm somewhat skeptical regarding the LBS that is conveniently located in that I was having problems with blow-outs, and they replaced one rim and built me another wheel, yet left the current pads in place. The brakes make a lot of noise and upon closer inspection, are worn to the shape/angle of the prior rims, thus the contact point to the new rim is just that, a point that is wearing a line into the new rim. I would've preferred that the LBS ask me if I want the pads replaced with the new rim and taken care of it at one time. It would have been money well spent in my opinion-and not too much of it at that. Thanks for letting me rant.
05-31-03, 09:28 PM
Any shop should carry them. Depending on the shop they will be $4 to$6 a pair. You can get fancy ones but these seem to work well and look "right"
They are what we call Huffy pads, becausewe use them on the inexspensive bikes a lot.
I'm with Rev on this one too. You sure don't need $25.00 Kool Stops.
You can get really cheap brake pads from X-Mart, but the composition is too hard and does not brake well.
Like Rev says, go to a bike shop and get a good pair for around $6.00.
I have the real deal salmon colored brake pads (used, but nice) if you need to stay true to the bike.
You might consider changing from center pulls to side pulls. I can sell you some used side-pulls too. Contact me through the forums.
06-02-03, 07:38 AM
Thanks for the input. I went by the LBS on Fri. and they had pads ranging from the $2.99/Pair (I think) all the way up to the $25 ones. I asked for their advice and they basically told me it was my call. I figured I'd start w/the cheapest ones and go from there. Got them installed and braking is much better. I believe the age of the old pads had a lot to do with their lack of performance (kind of hard compared with the new ones) I believe I need to toe-in the front pads slightly more as I've still got a little noise, but overall I believe these will be fine. (I hope I didn't just jinx myself) Thanks again for the advice.
I want a new bike - even though this one is really all I need.
Powered by vBulletin® Version 4.1.12 Copyright © 2014 vBulletin Solutions, Inc. All rights reserved.