Clydesdales/Athenas (200+ lb / 91+ kg) - Clipless help
Bikeforums.net is a forum about nothing but bikes. Our community can help you find information about hard-to-find and localized information like bicycle tours, specialties like where in your area to have your recumbent bike serviced, or what are the best bicycle tires and seats for the activities you use your bike for.
05-15-08, 08:25 PM
So I made the switch to clipless pedals from clips and straps. Crankbrothers eggbeaters and specialized comp mountain shoes. I tried clipping in on the trainer for a couple days and got very frustrated. I rode them on my commute today. Once I got clipped in I loved them. The problem was getting clipped in. I tried rolling in from the front, and rolling in from the back. After trying this several times I resorted to blindly stabbing at the pedals hoping to get lucky. So does anyone have any advice for clipping into eggbeaters? On a positive note I didn't have any trouble getting unclipped:).
This issue is the reason I have resisted moving to eggbeaters. I know people that swear by them, some people have had issues clipping in and wanted to throw them in the trash. I've stuck with my SPD's for the moment.
05-15-08, 10:28 PM
When I first started using them it was a little tough to clip in. Now it seems effortless and very easy. I am not sure if it really is any easier of if I just got used to the location of the clips/pedal etc. I find them quite comfortable and have forgotten to unclip when I stop a couple of times. I am using the Candy C version so it might be a little different for just the egg beaters.
05-16-08, 12:29 AM
I use the Crank Brothers Eggbeater pedals on both my road and commute bike. I'm using them with the Shimano MT31 shoe. I found them a bit difficult to get used to at first, but now I love them. Here are a few suggestions:
1) If you're having trouble getting clipped in, or staying clipped once you are in, think about using the shims provided with the pedal. The shim isn't very thick, but it may raise the cleat just enough to make clipping easier. I tried my shoes with and without the shims and eventually settled on not using the shims.
2) Keep practicing! When I first got the pedals, I had quite a bit of trouble using them while on the trainer. For some strange reason, I found it easier to clip in when I was out riding. It probably took me the better part of two weeks, riding 4-5 days/week before I felt truly comfortable with the pedal.
3) Play around with the placement and angle of the cleat. All placements are not created equal! I had to futz around with this before I found a position that was easy to clip. In my case, I push the cleat as far forward in the mounting area as possible and angle it slightly. I found it helps to look at the bottom of the shoe and then try to visualize which way the cleat would be pointing when I tried to clip in. I noticed I have a tendency to point my toe toward the frame, so it helped to rotate the cleat slightly. It might also help to clip the shoes in, step out of them, then take a look at where they're positioned in relation to the pedal.
4) The cleat is further back on the shoe than you think! If you look at the bottom of the shoe, it looks like the cleat is pretty far forward. It isn't. Or perhaps I should say: my biggest mistake was thinking that the cleat was further forward than it actually was.
5) I only clip and unclip one foot while riding. It's one less thing to worry about. My right foot tends to stay clipped in for an entire ride. If I need to stop, I unclip my left foot. I don't even bother to practice clipping and unclipping with my right foot! If worse comes to worst and I can't get the left foot clipped, I can still ride pretty effectively with the right foot clipped and the left just resting on the top of the pedal. I'll do this until I reach a place where it's convenient to try to re-clip the left foot or look down at the pedal to figure out what's going wrong.
Now that I've told you all the important, but useless, background stuff here's the secret: you need to catch the front of the clip with the front of the cleat then step down hard. If this doesn't work and you're sure you've caught the front of the clip with the cleat, move your heal left and right a bit (like you're squashing a bug or putting out a cigarette butt) while still stepping down hard. These pedals, especially when brand-new, need some real force to make the cleat seat. If you're trying to, say, clip-in at the top of a pedal stroke you may have difficulty. Give 'em a good stomp! The nice thing is: if you give them a hard stomp and the cleat is anywhere close to being in the right place, you'll end up clipped in.
05-16-08, 03:00 AM
It took me a little while to get used to clipping in them as well. I sat in my bathroom on the bike for about 2 hours, clipping in and out... getting used to it.
Eventually you'll get it, sooner than later.
Powered by vBulletin® Version 4.1.12 Copyright © 2013 vBulletin Solutions, Inc. All rights reserved.