Lets_roll
03-18-09, 10:27 PM
I'm looking a decent clamp that fits the 606a. I'm ordering from DE.
This light will be mounted to a MTB bars if it matters.
Thanks
This light will be mounted to a MTB bars if it matters.
Thanks
Electronics, Lighting, & Gadgets - ~+~+~Help choosing WF-606a bike Clamp ~+~+~
Bikeforums.net is a forum about nothing but bikes. Our community can help you find information about hard-to-find and localized information like bicycle tours, specialties like where in your area to have your recumbent bike serviced, or what are the best bicycle tires and seats for the activities you use your bike for.View Full Version : ~+~+~Help choosing WF-606a bike Clamp ~+~+~
Unknown Cyclist
03-19-09, 03:33 AM
I've got a 606A and these:
http://www1.dealextreme.com/productimages/sku_13004_1_small.jpg
The 606A fits the Fenix well, but the mount does take up a lot of barspace.
http://www1.dealextreme.com/productimages/sku_15642_2_small.jpg
This one is much too large.
http://www1.dealextreme.com/productimages/sku_0792_2_thumb.jpg
Pivot pins and centrebolt were rusty, didn't seem well made, I threw it away so can't check the fit.
My favourite for the 606A is this one:
http://www1.dealextreme.com/productimages/sku_15342_2_small.jpg
Universal Bicycle Mount (http://www.dealextreme.com/details.dx/sku.15342)
Most of the mounts are too large for the 606A, but this one fits well with a little bit of tape around the torch. Sideways adjust is a little bit slack but can be tightened - it's a self tapping screw, after experimenting and taking it apart a few times I replaced the screw with a nut and bolt. :)
http://www1.dealextreme.com/productimages/sku_13004_1_small.jpg
The 606A fits the Fenix well, but the mount does take up a lot of barspace.
http://www1.dealextreme.com/productimages/sku_15642_2_small.jpg
This one is much too large.
http://www1.dealextreme.com/productimages/sku_0792_2_thumb.jpg
Pivot pins and centrebolt were rusty, didn't seem well made, I threw it away so can't check the fit.
My favourite for the 606A is this one:
http://www1.dealextreme.com/productimages/sku_15342_2_small.jpg
Universal Bicycle Mount (http://www.dealextreme.com/details.dx/sku.15342)
Most of the mounts are too large for the 606A, but this one fits well with a little bit of tape around the torch. Sideways adjust is a little bit slack but can be tightened - it's a self tapping screw, after experimenting and taking it apart a few times I replaced the screw with a nut and bolt. :)
seeker333
03-19-09, 12:08 PM
you can attach one with duct tape, plastic tie strap and old inner tube rubber or bar grips for shock absorption - if you don't intend to remove it
they're not that heavy or hard to retain.
be sure to pad it somehow - many of the DE lights are built kinda crappy, tolerance-wise - the lightest shock will break circuit momentarily, causing it to shut off or advance mode.
i doubt the store-bought flashlight holders offer much in the way of shock absorption
they're not that heavy or hard to retain.
be sure to pad it somehow - many of the DE lights are built kinda crappy, tolerance-wise - the lightest shock will break circuit momentarily, causing it to shut off or advance mode.
i doubt the store-bought flashlight holders offer much in the way of shock absorption