Folding Bikes - Brompton hub gear maintenance
Bikeforums.net is a forum about nothing but bikes. Our community can help you find information about hard-to-find and localized information like bicycle tours, specialties like where in your area to have your recumbent bike serviced, or what are the best bicycle tires and seats for the activities you use your bike for.
02-27-05, 02:32 AM
My Brompton L3 has become a 2-speed, I can no longer adjust the cable tension in such a way that all 3 gears are usable. When tension is loose enough to use 3rd (direct drive?) I can't get into 1st. When the cable is tight enough to use 1st, it won't drop into 3rd. This started after I'd had the bike about 4 months (commuting 50 miles a week).
I don't seem to be the only person who's had this problem, I found someone on the Bromptontalk group on Yahoo with same issue:
I'm in 2 minds about whether to try stripping down & lubing the hub myself or take the complete bike back to LBS where I bought it and ask them to fix it or replace the hub under warranty. Reluctant to use latter option as I suspect it would mean the bike being off the road for a lengthy period and I use it every day.
Anyone heard of this type of problem with SRAM Spectro T3 or other 3-speed hubs?
02-27-05, 04:26 AM
I do not believe that lubrication is the issue on not getting gear change and on such a new bike. I have a Brompton but it is a Sturmey Archer, I have a lot of mileage up with no problems.
I would not be very tempted to open the rear hub myself. I would bring it back to the shop and if they take longer than 1 week look for a loan or replacement back wheel with hub from them.
As an aside I have 3 bikes running, the Brompton, A Sirrus and a Mountain bike.
Although I don't use the Brompton every day I do go through phases of using it for 100 miles a week commute. It is very low maintenance. I have practically rebuilt the Sirrus but have only changed chain and spring tensioner on Brompton.
About 4 years ago I researched heavily the Brompton hub etc before buying. Your hub should run for many many many miles without adjustment.
Bottom line - take it back and get it fixed. The downside to the Brompon if that can be called a downside is that true Brompton users - that use them everyday invariably buy a second one for when problems occur with first.
02-27-05, 11:49 PM
This was my experience as well, except I caused it.
When I first purchased my Brompton, I rode it and never had a problem. As I got used to it, I read that a rear tire change could be tricky the first time if you've never taken the rear wheel off, so I thought I would practice to make sure I got the hang of it.
In my case, my 3 --> 2 speed was caused because I pushed the chain indicator too far into the plastic adjustor when I replaced the wheel. Not only that, but when I put it in the adjustor, it looked too loose to me, so I loosened the adjustor and pushed it up the cable. That's when my problems started, but I didn't know how to fix my mistakes.
When I finally had an LBS guy check it out, he said I only had to push the chain indicator into the adjustor until I heard two clicks - the cable is supposed to be rather slack. But he did other things as well:
- When he first examined the problem, he kept looking at the cable, not the hub.
- He unscrewed the adjustor and took it off, then he re-seated the cable over the pulley housing.
- He inspected the cable and rewove the cable end by hand as it was beginning to unthread.
- He screwed the adjustor closer to the end of the cable, then pushed the chain indicator into it a couple of clicks and tested the gear shifting.
It worked. Now I have all my gears working.
Did you, by any chance, unseat the adjustor while you were adjusting the cable tension? How far did you push in the chain indicator?
Powered by vBulletin® Version 4.1.12 Copyright © 2013 vBulletin Solutions, Inc. All rights reserved.