Presta valve issues
06-21-17, 05:48 PM
#26
Senior Member
Join Date: Apr 2007
Posts: 6,760
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1109 Post(s)
Liked 1,200 Times
in
760 Posts
I've only scanned the responses but:
(1) it certainly does not take more than 20 psi to "seal" a presta valve. A presta valve will totally hold air in a tube that is slightly pumped up outside of a tire, and that's less than 20 PSI.
(2) make sure the valve core is tight into the valve stem. Some (most?) presta valves cores can be tightened and loosened and removed. Make sure it's tight. I'm talking about the valve core, not the valve closing mechanism. I've had many a tube with slow leaks solved by tightening the valve core. Hope that makes sense. In the attached picture you can see little flat areas that you'd use to loosen and tighten the valve core. They also show a special tool, but a needle nose pliers would work fine.
(3) tube outside of the tire - submerse it bit by bit, slowly, in a sink of water. Even at the low pressures needed to expand an innertube outside of a tire, it will show bubbles at the leak. Sometimes you you have to look very carefully and move the tube around its circumference very slowly. It certainly doesn't take more than 20 PSI for the valve to hold air and to show bubbles. I'd start at the valve since it might be the problem area. If so, see #1 above.
(1) it certainly does not take more than 20 psi to "seal" a presta valve. A presta valve will totally hold air in a tube that is slightly pumped up outside of a tire, and that's less than 20 PSI.
(2) make sure the valve core is tight into the valve stem. Some (most?) presta valves cores can be tightened and loosened and removed. Make sure it's tight. I'm talking about the valve core, not the valve closing mechanism. I've had many a tube with slow leaks solved by tightening the valve core. Hope that makes sense. In the attached picture you can see little flat areas that you'd use to loosen and tighten the valve core. They also show a special tool, but a needle nose pliers would work fine.
(3) tube outside of the tire - submerse it bit by bit, slowly, in a sink of water. Even at the low pressures needed to expand an innertube outside of a tire, it will show bubbles at the leak. Sometimes you you have to look very carefully and move the tube around its circumference very slowly. It certainly doesn't take more than 20 PSI for the valve to hold air and to show bubbles. I'd start at the valve since it might be the problem area. If so, see #1 above.
06-21-17, 07:32 PM
#27
Senior Member
Join Date: Nov 2009
Location: Pasco county, Florida
Posts: 74
Bikes: Cannondale R600 Triple, Me-Mover FIT 2.0
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 19 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Do you mean you switched to a Silca chuck?
I've got the Nashbar L'Orange V2 pump, and I like the concept but man is it hard to pull the chuck off! I've gotten into the habit of spitting into the chuck every time I use it so there's a little lubrication in there.
I once ripped a schraeder valve right out of a tire!
I've got the Nashbar L'Orange V2 pump, and I like the concept but man is it hard to pull the chuck off! I've gotten into the habit of spitting into the chuck every time I use it so there's a little lubrication in there.
I once ripped a schraeder valve right out of a tire!
I called the Serface home office, they didn't believe I was destroying the presta valves with a new chuck they sent to replace a well worn one. I was going through tubes every 4 to 6 weeks until I changed to Silca valve cores.
