Worn out hex screw!
04-08-06, 11:40 PM
#1
Senior Member
Thread Starter
Join Date: Dec 2005
Location: San Diego
Posts: 605
Bikes: Batavus Old Dutch
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Worn out hex screw!
I was trying to install new thumbies for my gear shifters but the hex screw on my right grip shifter won't come off! I think it is worn out, because the left one came off just fine. It still retains its shape, though. I tried the next biggest size and that won't fit at all. Any suggestion on how to remove a tightly screwed hex that has a worn out head? Thanks!
04-09-06, 05:51 AM
#2
Senior Member
Join Date: Oct 2005
Location: Fresno, CA
Posts: 4,454
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 128 Post(s)
Likes: 0
Liked 12 Times
in
10 Posts
So it sounds as if the hex hole is rounded out. You could try an "american"-measurement hex wrench set, to see if there's one slightly bigger than the metric one, that'll fit in the enlarged hole. But I think this is unlikely anyway. If you can get anything to work with hex wrenches, it'll probably have to involve
(a) soaking the threads in question in WD-40 or liquid wrench
(b) very careful turning of the wrench while pressing the wrench head full-force into the bolt - think of a phillips screw that you're worried about stripping
If this doesn't work, best thing to do is use a power tool to drill a flat groove into the hex bolt head, so you can use a flathead screwdriver on it. This method is sometimes used with hex bolts on SPD-style cleats, where the surface has worn down and a hex wrench is no longer usable to loosen the cleats.
(a) soaking the threads in question in WD-40 or liquid wrench
(b) very careful turning of the wrench while pressing the wrench head full-force into the bolt - think of a phillips screw that you're worried about stripping
If this doesn't work, best thing to do is use a power tool to drill a flat groove into the hex bolt head, so you can use a flathead screwdriver on it. This method is sometimes used with hex bolts on SPD-style cleats, where the surface has worn down and a hex wrench is no longer usable to loosen the cleats.
__________________
"c" is not a unit that measures tire width
"c" is not a unit that measures tire width
04-09-06, 08:51 AM
#3
Senior Member
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225
Bikes: Catrike 559 I own some others but they don't get ridden very much.
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 643 Times
in
364 Posts
Originally Posted by chicbicyclist
I was trying to install new thumbies for my gear shifters but the hex screw on my right grip shifter won't come off! I think it is worn out, because the left one came off just fine. It still retains its shape, though. I tried the next biggest size and that won't fit at all. Any suggestion on how to remove a tightly screwed hex that has a worn out head? Thanks!
04-09-06, 09:06 AM
#4
Senior Member
Join Date: Dec 2005
Location: northern California
Posts: 5,603
Bikes: Bruce Gordon BLT, Cannondale parts bike, Ecodyne recumbent trike, Counterpoint Opus 2, miyata 1000
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
If all else fails could the bolt be removed by first using a drill of slightly smaller diameter than the original hole to drill out most of the bolt, using a slightly undersized tap to chase out the fragments, then a correct tap to re-chase the threads? Any machinists to advise on this?
04-09-06, 09:12 AM
#5
Gone, but not forgotten
Join Date: Jul 2002
Location: Newtonville, Massachusetts
Posts: 2,301
Bikes: See: https://sheldonbrown.org/bicycles
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 24 Post(s)
Likes: 0
Liked 6 Times
in
5 Posts
Originally Posted by Retro Grouch
Try a brand new allen wrench. That'll work more often than you'd think.
Sheldon "Sparky" Brown
Code:
+------------------------------------+ | Immigrants are not our burden, | | They are our wealth --Jane Adams | +------------------------------------+
04-09-06, 09:19 AM
#6
Klaatu barada nikto
Join Date: Sep 2004
Location: Southern NH
Posts: 1,453
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Screw extractors ("easy outs") are always an option, if all else fails. Unfortunately, they are hardly ever "easy" to use. But, they do work.
04-09-06, 09:20 AM
#7
Senior Member
Join Date: Jun 2005
Location: Kentucky
Posts: 2,599
Bikes: 06 Lemond Reno, 98 GT Timberline mtn.bike
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 427 Post(s)
Liked 699 Times
in
436 Posts
Another option is to use some JB Weld (available at any auto store and some X-marts), and expoxy the wrench to the bolt. Allow it to dry solid and just unscrew the bolt. Just be careful not to get any on any other parts! You can then cut the wrench off where it was expoxyed, and still have use of the hex wrench, it will just be a bit shorter.
