Lemond Bikes and Ticking @ Headset/Stem Area??
#1
Banned.
Thread Starter
Join Date: Dec 2005
Location: Upland Ca
Posts: 19,895
Bikes: Lemond Chambery/Cannondale R-900/Trek 8000 MTB/Burley Duet tandem
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 4 Times
in
3 Posts
Lemond Bikes and Ticking @ Headset/Stem Area??
I have this ticking near my stem/ headset area. Had it when my bike was a Tourmalet. Broken frame was replaced with a Chambery (partial cf and alum). I still hear the ticking so I'm puzzled. Though it might have been the low end fork or headset, but I guess not. The fork was also replace so that leaves that out. HS too! Ihave replace d the front wheel with another, still the tick.
More of a tick and not a pop, can't feel it! Happens whne I plac pressure on the hb's as if to stand. Ticking is more frequent now. I tried lubing the stem bolts on both ends. I've loosened the HS, tightened the HS but still the tick.
SO I'm thinkin gmaybe it the stem. But run into a bud today on teh bike. I ask about his stem as he has nice Tomson on his Lemond BA. Looks sweet and snug. I mention the tick and he says he hears the same noise in his stem HS area when he stands applying pressure on the HB's.
Only thin I can figure is that they both have Bontrager bars (mine are, I think his too). I've taken my bars off, cleaned, lubed, tried it both ways, still the tick!
Has anyone heard of such a thing on Lemond bikes, maybe even Treks since they use the same components? I've cleanded, lubed, then cleaned agin every friggin' thing I can imagine. Cleanded spacers, tried it without a spacer, test ride with very loose setting on the berings.
I'm thinking maybe use some sort of a coating on the hb's under the sem clamp? A gasket seal of some sort?
I hate that friggin tick!
More of a tick and not a pop, can't feel it! Happens whne I plac pressure on the hb's as if to stand. Ticking is more frequent now. I tried lubing the stem bolts on both ends. I've loosened the HS, tightened the HS but still the tick.
SO I'm thinkin gmaybe it the stem. But run into a bud today on teh bike. I ask about his stem as he has nice Tomson on his Lemond BA. Looks sweet and snug. I mention the tick and he says he hears the same noise in his stem HS area when he stands applying pressure on the HB's.
Only thin I can figure is that they both have Bontrager bars (mine are, I think his too). I've taken my bars off, cleaned, lubed, tried it both ways, still the tick!
Has anyone heard of such a thing on Lemond bikes, maybe even Treks since they use the same components? I've cleanded, lubed, then cleaned agin every friggin' thing I can imagine. Cleanded spacers, tried it without a spacer, test ride with very loose setting on the berings.
I'm thinking maybe use some sort of a coating on the hb's under the sem clamp? A gasket seal of some sort?
I hate that friggin tick!
#2
Banned.
Thread Starter
Join Date: Dec 2005
Location: Upland Ca
Posts: 19,895
Bikes: Lemond Chambery/Cannondale R-900/Trek 8000 MTB/Burley Duet tandem
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 4 Times
in
3 Posts
Well, not the hb's. Took 'em out and still the tick!....Thanks for all the suggestions so far!
Did take out the lil shim/race? that sits on the bearing set. Greased it so we'll see tomorrow. Keep the ideas coming boys!
Did take out the lil shim/race? that sits on the bearing set. Greased it so we'll see tomorrow. Keep the ideas coming boys!