Polish dull paint - car wax, Pledge, spit?
#1
Senior Member
Thread Starter
Join Date: Nov 2004
Location: Belgium
Posts: 664
Bikes: ca.1975 Gitane Interclub - 90's Colnago Master Competition- ca.'84 Merckx Corsa - '77 Groene Leeuw - ca. '78 Guerciotti - ca.1984 L'Express - 1974 Gitane 'Super Olympic' - Peugeot 1981 PXN10 - 1975 Peugeot PR10 -1974 Norta -1974 Peugeot PX10 LE
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Polish dull paint - car wax, Pledge, spit?
Talking 'bout this kind of 'satin'-look paint; is it possible to get a glossy finish
or is it a lost cause (don't know a lot about paint, I'm afraid):
or is it a lost cause (don't know a lot about paint, I'm afraid):
Last edited by joe v; 10-03-06 at 03:33 PM.
#2
Senior Member
Join Date: May 2006
Location: Denver, CO
Posts: 750
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
You might be able to shoot it with a clear gloss coat. If the paint is just oxidized, go to an auto paint store and get some buffing compound and buff it out.
#3
Senior Member
Join Date: Jul 2005
Posts: 3,268
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 118 Post(s)
Likes: 0
Liked 50 Times
in
25 Posts
Finesse II by DuPont. Its the final buff compound they use for shining up show paind jobs. If it doesn't work, your paint is probably too far gone. You can get it at auto paint supply stores.bk
#4
Senior Member
Progressive abrasives, applied by hand. Start out with some mild cleaner/wax, like Meguirs, on a small section. If it doesn't work, move up to polishing compound, followed by cleaner wax. If that doesn't work, go to rubbing compound, polishing compound, cleaner wax. Be careful with the rubbing compound, it will go right through the paint on any sharp edges, like lugs, etc. And of course, don't use harsh abrasives on decals.
If the rubbing compound doesn't do it, I would give up.
If the rubbing compound doesn't do it, I would give up.
__________________
Il faut de l'audace, encore de l'audace, toujours de l'audace
1980 3Rensho-- 1975 Raleigh Sprite 3spd
1990s Raleigh M20 MTB--2007 Windsor Hour (track)
1988 Ducati 750 F1
Il faut de l'audace, encore de l'audace, toujours de l'audace
1980 3Rensho-- 1975 Raleigh Sprite 3spd
1990s Raleigh M20 MTB--2007 Windsor Hour (track)
1988 Ducati 750 F1
#5
Senior Member
Join Date: Feb 2005
Location: Tampa
Posts: 96
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Just to follow up on Rensho's excellent advice, once you have stepped up the aggressiveness scale to achieve the results you desire, you'll want to step back down the scale using the products in reverse order to get optimal results.
From what I can tell from your photo, I think you'll be pleased with the results. Of course, with metallics paints, it can be hard to predict how they'll respond to polishing.
BTW, what's with the vintage Campy decals and the Suntour shifters? Not judging, just curious.
From what I can tell from your photo, I think you'll be pleased with the results. Of course, with metallics paints, it can be hard to predict how they'll respond to polishing.
BTW, what's with the vintage Campy decals and the Suntour shifters? Not judging, just curious.
#6
Senior Member
Join Date: Nov 2005
Location: Hobart
Posts: 126
Bikes: Schwinn, National, Tassie Cycle, Avanti, Standish
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Any brand of automotive 'cut & polish' should make a big difference. The 'cut' removes oxidised paint that causes dullness along with scuffs, dirt and minor scratches, and the 'polish' does just that - a nice new shine and a protectice coat of silicone wax.
#7
Mr. Maximan1
Join Date: Sep 2006
Location: Anaheim and Fullerton (SoCal)
Posts: 1,300
Bikes: Puch Superleicht, Nishiki moutain project, Trek 2300 carbon composite
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Buy some Rubbing Compound in Wal*Mart or wherever and polish it off. Make sure the paint is dust free first .
__________________
www.olgapetrovart.com
www.olgapetrovart.com
#8
Senior Member
Thread Starter
Join Date: Nov 2004
Location: Belgium
Posts: 664
Bikes: ca.1975 Gitane Interclub - 90's Colnago Master Competition- ca.'84 Merckx Corsa - '77 Groene Leeuw - ca. '78 Guerciotti - ca.1984 L'Express - 1974 Gitane 'Super Olympic' - Peugeot 1981 PXN10 - 1975 Peugeot PR10 -1974 Norta -1974 Peugeot PX10 LE
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Originally Posted by Toyman991
BTW, what's with the vintage Campy decals and the Suntour shifters? Not judging, just curious.
Anyways, thanks for the replies!
#9
Banned.
Join Date: Feb 2003
Location: Fort Wayne, Indiana
Posts: 4,761
Bikes: 84 Trek 660 Suntour Superbe; 87 Giant Rincon Shimano XT; 07 Mercian Vincitore Campy Veloce
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
Originally Posted by San Rensho
Progressive abrasives, applied by hand. Start out with some mild cleaner/wax, like Meguirs, on a small section. If it doesn't work, move up to polishing compound, followed by cleaner wax. If that doesn't work, go to rubbing compound, polishing compound, cleaner wax. Be careful with the rubbing compound, it will go right through the paint on any sharp edges, like lugs, etc. And of course, don't use harsh abrasives on decals.
If the rubbing compound doesn't do it, I would give up.
If the rubbing compound doesn't do it, I would give up.
Don't listen to these other people telling you to go to the rubbing compound first...THAT IS WRONG!!
You always take the less aggressive path first then work your way up. I have classic cars and this is what I do with any car I'm trying to get dullness out of the paint. In fact with modern clear coats you can't even use a rubbing compound on it because once you strip off the clear coat your paint is screwed. And bike paint jobs are not as good as car paint jobs so you really have to be careful you don't get to aggressive. I would try the cleaner wax first as Rensho mentions and buff lightly, if that didn't work then use the cleaner wax again but buff harder and do this approach throughout his steps.
And the Mequirs product that Rensho mentions is very good stuff; it's what I use on my cars, and I don't throw whatever dime store schit I can find on my cars!!
Also you have a silver bike, silver and red are the two fastest colors to oxidize or fade. Once you have the shine back then lay down a protective wax coating using Mequirs Gold Class which has UV protection built in, and reapply about every 3 months.
Last edited by froze; 10-05-06 at 12:29 AM.
#10
Guest
Posts: n/a
Mentioned: Post(s)
Tagged: Thread(s)
Quoted: Post(s)
After looking at the picture, I would say lost cause!
You'd be better off either just waxing it and call it good, or take it apart and have a powdercoat finish applied. PC would be a better return on your $$$. Good waxes/polishing compounds aren't cheap. Around here a powdercoating is $100, give or take.
note; if you use the heavier cut compounds on metallic paint, you will scratch the metal flakes and end up about where you started.
Or you could try your hand at a rattle can paint job for less than $50.
Just my 2 cents. Good luck with that!
You'd be better off either just waxing it and call it good, or take it apart and have a powdercoat finish applied. PC would be a better return on your $$$. Good waxes/polishing compounds aren't cheap. Around here a powdercoating is $100, give or take.
note; if you use the heavier cut compounds on metallic paint, you will scratch the metal flakes and end up about where you started.
Or you could try your hand at a rattle can paint job for less than $50.
Just my 2 cents. Good luck with that!
#11
Banned.
Join Date: Feb 2003
Location: Fort Wayne, Indiana
Posts: 4,761
Bikes: 84 Trek 660 Suntour Superbe; 87 Giant Rincon Shimano XT; 07 Mercian Vincitore Campy Veloce
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
Originally Posted by Dr.Deltron
After looking at the picture, I would say lost cause!!
Don't let negative people influence your decision, do the cleaner/wax program Rensho outlined and you might be surprised. And so what if you spend money on wax products that don't work? Worst case is that you use those products on your car!! Except don't use the rubbing compound on your car. Just buy the first step first and try it over and over and over, if nothing happens then buy the next step and so on.
Try the first step several times because it's the least aggressive and it might just work. Be careful around decals. You may have to expend some physical energy, but that's free.
#12
Guest
Posts: n/a
Mentioned: Post(s)
Tagged: Thread(s)
Quoted: Post(s)
Originally Posted by froze
1) I looked at the same pix as you and I don't see it as a lost couse because in a picture you can't really tell.
2) Don't let negative people influence your decision,
3) You may have to expend some physical energy, but that's free.
2) Don't let negative people influence your decision,
3) You may have to expend some physical energy, but that's free.
2A) Not negative, just realistic.
3A) FREE??? Time IS money!
AND what about the decals/stickers? Unless you want to lose those anyway.
WAX that frame & call it good. Until it DOES need a refinish. Unless you have WAY too much time on your hands AND a gallon or two of elbow grease!
#13
Banned.
Join Date: Feb 2003
Location: Fort Wayne, Indiana
Posts: 4,761
Bikes: 84 Trek 660 Suntour Superbe; 87 Giant Rincon Shimano XT; 07 Mercian Vincitore Campy Veloce
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
Originally Posted by Dr.Deltron
1A) From THAT picture I can pretty much tell.
2A) Not negative, just realistic.
3A) FREE??? Time IS money!
AND what about the decals/stickers? Unless you want to lose those anyway.
WAX that frame & call it good. Until it DOES need a refinish. Unless you have WAY too much time on your hands AND a gallon or two of elbow grease!
2A) Not negative, just realistic.
3A) FREE??? Time IS money!
AND what about the decals/stickers? Unless you want to lose those anyway.
WAX that frame & call it good. Until it DOES need a refinish. Unless you have WAY too much time on your hands AND a gallon or two of elbow grease!
#14
Banned.
Join Date: Feb 2003
Location: Fort Wayne, Indiana
Posts: 4,761
Bikes: 84 Trek 660 Suntour Superbe; 87 Giant Rincon Shimano XT; 07 Mercian Vincitore Campy Veloce
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
Originally Posted by joe v
Talking 'bout this kind of 'satin'-look paint; is it possible to get a glossy finish
or is it a lost cause (don't know a lot about paint, I'm afraid):
or is it a lost cause (don't know a lot about paint, I'm afraid):
#15
"Purgatory Central"
Join Date: May 2005
Location: beautiful "Cypress Gardens" florida
Posts: 1,757
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 3 Times
in
2 Posts
Originally Posted by joe v
Talking 'bout this kind of 'satin'-look paint; is it possible to get a glossy finish
or is it a lost cause (don't know a lot about paint, I'm afraid):
or is it a lost cause (don't know a lot about paint, I'm afraid):
Yeah I've also worked with faded/oxidized paint for 30 years too. The advice given by 'San Rensho' and 'froze' is very good. But you need to be patient. My advice is to cover the decals with a good automotive masking tape, then try the steps 'Rensho' advised, being careful around the decals. Use only your fingers and no machine. Test on the underside of the downtube or lower seattube until you find out what works good. Go slow and have fun bringing new life into that old paint.
#16
Junk Collector
Join Date: Jun 2005
Location: Chicago IL
Posts: 973
Bikes: 1987 Schwinn Circuit, 2012 Colnago M10, 1990 Schwinn CrissCross
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 34 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Is it definitely oxidized? Or was it a satin finish from the factory? If t's the latter, then a 'flattening agent' was added to the finish when it was sprayed, and it'll never shine properly. If it's just oxidized, but has NO clearcoat over it, then I'd go with Dr Del on this one. Trying to shine a metallic that has oxidized is a true hassle. If it DOES have a clear over it, there's some hope, but it may be too far gone.
#17
Banned.
Join Date: Feb 2003
Location: Fort Wayne, Indiana
Posts: 4,761
Bikes: 84 Trek 660 Suntour Superbe; 87 Giant Rincon Shimano XT; 07 Mercian Vincitore Campy Veloce
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
Originally Posted by duane041
Is it definitely oxidized? Or was it a satin finish from the factory? If t's the latter, then a 'flattening agent' was added to the finish when it was sprayed, and it'll never shine properly. If it's just oxidized, but has NO clearcoat over it, then I'd go with Dr Del on this one. Trying to shine a metallic that has oxidized is a true hassle. If it DOES have a clear over it, there's some hope, but it may be too far gone.
#18
Guest
Posts: n/a
Mentioned: Post(s)
Tagged: Thread(s)
Quoted: Post(s)
OK...I guess the point I was try to make is, that polishing a bike is
A ROYAL PAIN IN THE ELBOW! (and finger!)
especially a bike with what appear to be a number of stickers/decals. How much is YOUR time worth?
At $10/hour, a hundred dollars for a NEW powdercoat is probably a better way to go. If your time is worth MORE than $10/hr, even MORE reason to refinish. But if you'd rather work on your bike than WATCH TV, then definetly try to polish it out. Good luck with whatever you decide.
A ROYAL PAIN IN THE ELBOW! (and finger!)
especially a bike with what appear to be a number of stickers/decals. How much is YOUR time worth?
At $10/hour, a hundred dollars for a NEW powdercoat is probably a better way to go. If your time is worth MORE than $10/hr, even MORE reason to refinish. But if you'd rather work on your bike than WATCH TV, then definetly try to polish it out. Good luck with whatever you decide.
#20
Junk Collector
Join Date: Jun 2005
Location: Chicago IL
Posts: 973
Bikes: 1987 Schwinn Circuit, 2012 Colnago M10, 1990 Schwinn CrissCross
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 34 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
[QUOTE=froze As far as the bike manufacture using a flattening agent on the paint, that I wouldn't know without physically seeing the bike; but I can't remember any bike coming from a manufacture painted like that, but I guess that's possible.[/QUOTE]
I happen to have am "Outfitters" (?) MTB that is finished in a god-awful flat green. It's really ugly. But I doubt a road bike would be finished this way.
an Yeah, you're right, any oxidized paint is a drag. Especially when red goes pink
I happen to have am "Outfitters" (?) MTB that is finished in a god-awful flat green. It's really ugly. But I doubt a road bike would be finished this way.
an Yeah, you're right, any oxidized paint is a drag. Especially when red goes pink
#21
Banned.
Join Date: Feb 2003
Location: Fort Wayne, Indiana
Posts: 4,761
Bikes: 84 Trek 660 Suntour Superbe; 87 Giant Rincon Shimano XT; 07 Mercian Vincitore Campy Veloce
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
Originally Posted by Lossy
Or you could watch t.v. and work on the bike at the same time.
#22
Guest
Posts: n/a
Mentioned: Post(s)
Tagged: Thread(s)
Quoted: Post(s)
Originally Posted by froze
With what Dr Deltorn said about time is money, makes me wonder just how much money I spent watching TV or listening to the stereo!
Only job I've ever had that involved relaxing was driving a taxi!