Just popped a spoke - can I fix this?
#1
Senior Member
Thread Starter
Join Date: Jan 2006
Location: San Francisco
Posts: 77
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Just popped a spoke - can I fix this?
I've never done wheel work before and am wondering if it's a good idea for me to try and fix my wheel. I was actually just noticing it was out of true and this morning a spoke popped...so much for preventative maintenance!
It's just one spoke that popped, so if I bought a pack of spokes could I just replace the one spoke? From reading on the Park Tool website it seems a truing stand might be in order. Would it be easier to just take it to the shop? I'm not a bike mechanic newbie but as I mentioned I've never done wheel work.
Thanks,
--Illah
It's just one spoke that popped, so if I bought a pack of spokes could I just replace the one spoke? From reading on the Park Tool website it seems a truing stand might be in order. Would it be easier to just take it to the shop? I'm not a bike mechanic newbie but as I mentioned I've never done wheel work.
Thanks,
--Illah
#2
*
Join Date: Jan 2007
Posts: 3,458
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Front or rear? If you have to remove the cassette it means tools. Did the spoke break or just pop out of the nipple? If that's the case you may just have to replace the nipple (more common with aluminum). But you can handle this even without a stand by watching your wheel next to the brake pads. And you can buy just one spoke from your LBS, and buy a good spoke wrench.
#3
Senior Member
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225
Bikes: Catrike 559 I own some others but they don't get ridden very much.
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 643 Times
in
364 Posts
Returning your wheel to what it was before it broke the spoke is a relatively simple job. What it was before, however, was a wheel that was about to break a spoke. I doubt that's what you want.
The RIGHT way to fix it is to replace the broken spoke then to equalize the tension of all the spokes. Often the non-drive spokes have inadequate tension so the tension on every spoke has to be increased. Finally, the wheel will need to be retrued by tightening and loosening opposing pairs of spokes by an equal amount.
The RIGHT way to fix it is to replace the broken spoke then to equalize the tension of all the spokes. Often the non-drive spokes have inadequate tension so the tension on every spoke has to be increased. Finally, the wheel will need to be retrued by tightening and loosening opposing pairs of spokes by an equal amount.
#4
Senior Member
Thread Starter
Join Date: Jan 2006
Location: San Francisco
Posts: 77
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
So would you say that's a do-able job for me given my intermediate skills? A truing stand and spoke wrenches is about $50 which is probably in the range of what it would cost to have a mechanic do it for me, so I can go either way (though obviously learning to do it myself means I can fix it in the future). Would I need a spoke tensioner or is that more of an optional piece?
--Illah
--Illah
#5
*
Join Date: Jan 2007
Posts: 3,458
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Go for it! Desire is 90% of it, right? The tension meter's going to double your expenditure, would be nice to have, but I've built about 1/2 dozen wheelsets without one and have yet to have a spoke break or follow-up truing problems. Others swear by them, though, probably for good reason.
#6
Senior Member
Thread Starter
Join Date: Jan 2006
Location: San Francisco
Posts: 77
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Yeah, the meter alone would be $60+ so it's more than double Good to know it's do-able without...I'm probably going to go for it. As they say, teach a man to fish...
Wish me luck!
--Illah
Wish me luck!
--Illah
#7
Senior Member
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225
Bikes: Catrike 559 I own some others but they don't get ridden very much.
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 643 Times
in
364 Posts
Originally Posted by Illah
Would I need a spoke tensioner or is that more of an optional piece?
#8
Senior Member
Thread Starter
Join Date: Jan 2006
Location: San Francisco
Posts: 77
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I actually sissy'ed out and took it to the shop. Since it was a drive side spoke I'd need to get cassette removal tools too and adding it all up started to take it near $100. Maybe one day, but a LBS quoted me $25 so I figured I'd save myself the trouble.
Thanks for the help though - I definitely plan to do this myself at some point. Might still pickup the spoke wrenches and truing stand just to maintain trueness to hopefully prevent popped spokes in the future. Wheels are the 'final frontier' so to say in my bike tuning skillset so I should learn it eventually, I can handle pretty much every other part of the bike except these
--Illah
Thanks for the help though - I definitely plan to do this myself at some point. Might still pickup the spoke wrenches and truing stand just to maintain trueness to hopefully prevent popped spokes in the future. Wheels are the 'final frontier' so to say in my bike tuning skillset so I should learn it eventually, I can handle pretty much every other part of the bike except these
--Illah
Last edited by Illah; 03-28-07 at 05:35 PM.