remove a stripped crank arm?
#1
Member
Thread Starter
Join Date: Aug 2005
Posts: 29
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
remove a stripped crank arm?
Due to inattention on my part, I managed to strip the threads of my Campy crank where the removal tool threads in. This means I can't remove the crank arm, and naturally it's on the drive side.
Any hints how to remove it non-destructively?
I thought of an automotive pulley puller, but since the crank spider has five spindles, the pully puller won't grab.
I've tried propping the bike up and resting the spider on a couple of 2x4s and gently tapping on the bb axle with a rubber mallet and a bolt. Didn't work, and maybe I'm too afraid of bending or breaking something to give it adequate force.
It doesn't look like a job for a helicoil.
Help?
Any hints how to remove it non-destructively?
I thought of an automotive pulley puller, but since the crank spider has five spindles, the pully puller won't grab.
I've tried propping the bike up and resting the spider on a couple of 2x4s and gently tapping on the bb axle with a rubber mallet and a bolt. Didn't work, and maybe I'm too afraid of bending or breaking something to give it adequate force.
It doesn't look like a job for a helicoil.
Help?
#2
Asshat
Join Date: Jul 2005
Location: Atlanta, GA
Posts: 333
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I have the same problem on one of my bikes, but I still haven't had to pull the crank (sealed BB). A two prong puller wouldn't work?
#3
Your mom
Join Date: Aug 2006
Posts: 2,544
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
There have been 3-4 threads on this in the past 9 months. Do a search. Options include: Bearing puller, destruction, and a crazy technique with a socket on a cement floor.
#4
uberNEWB
Join Date: Jun 2007
Location: Montreal, Quebec
Posts: 528
Bikes: Haro V2 [rip / stolen], PEUGEOT '93 SELECT
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#5
Senior Member
Originally Posted by tellyho
There have been 3-4 threads on this in the past 9 months. Do a search. Options include: Bearing puller, destruction, and a crazy technique with a socket on a cement floor.
Hey, I resemble that comment. By the way, the method works very well.
Find a socket that just fits inside the square of the crank arm.
Put the socket on a cement floor.
Place the bike over the socket so the socket is inside the square of the crank arm. Have someone hold the bike.
With a flat punch and a BFH (big f@cking hammer), hammer on the crank arm as close as you can to the bottom bracket. Put a big flat washer between the punch and the crank arm to protect the soft metal.
__________________
Il faut de l'audace, encore de l'audace, toujours de l'audace
1980 3Rensho-- 1975 Raleigh Sprite 3spd
1990s Raleigh M20 MTB--2007 Windsor Hour (track)
1988 Ducati 750 F1
Il faut de l'audace, encore de l'audace, toujours de l'audace
1980 3Rensho-- 1975 Raleigh Sprite 3spd
1990s Raleigh M20 MTB--2007 Windsor Hour (track)
1988 Ducati 750 F1
#6
Hammer Time
Join Date: Mar 2007
Location: Australia
Posts: 258
Bikes: Paconi, Hillman, Sun Tourer + Mongoose Tetra SX
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Another way is to ride the bike until the crank comes loose... Just make sure you check every once and a while to see whether it is loose, as riding with a loose crank can damage it even more - that is if you want to keep the crank.
Make sure you leave the screw in, so the crank doesn't just fall off - and ride carefully. I have never had to do this, but I read somewhere that it works.
Make sure you leave the screw in, so the crank doesn't just fall off - and ride carefully. I have never had to do this, but I read somewhere that it works.