Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Hints and tricks thread

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Hints and tricks thread

Old 09-16-10, 04:42 AM
  #276  
Junior Member
 
constant mesh's Avatar
 
Join Date: Aug 2010
Location: Pannonia
Posts: 22

Bikes: SCOTT Tampico

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Just remember these two:

#1
Guitar picks are best tools for removing/disassembling/prying rubber and plastic components. In heat of the moment we usually take a screwdriver and partially destroy the stuff with it. Won't happend with a nylon pick. They are up to 2mm thick.

#2
Cantilever braking surface on your rim can be easily clean with a 'gator grit'. It's a synthetic steel wool, give it a good rub, then degrease it with a degreaser (something like M600 or similar, you can get it in any auto body shop, usually the call it "silicone spot remover", it's for prep before painting - won't destory any rubber or plastics, it's very mild but effective) or soapy water.
constant mesh is offline  
Old 09-29-10, 01:12 AM
  #277  
Junior Member
 
Join Date: Sep 2010
Posts: 8
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Another destructive method of removing a freewheel

I needed to remove a Maillard freewheel. The tool
needed to remove this freewheel was the CT-3 from bicycletool.com (https://www.bicycletool.com/normandym...wheeltool.aspx) or the Normandy Maillard tool. The freewheel has 24 splines where the tool should fit. I didn't have the possibilitty to acquire the tool. To remove the freewheel I used a 27 milimeters hex bolt with two nuts. The head of the bolt fits perfectly in the splines of the freewheel, the freewheel as an inside diameter of 31 milimeters. The two nuts where strongly screwed against each other. One of the nuts was clamped in a benchwise and the head of the bolt was used as the freewheel removal tool.
Some images of the nut and the freewheel after removal.

https://i53.tinypic.com/w2obuo.jpg
https://i51.tinypic.com/25frlon.jpg
https://i52.tinypic.com/jf9so5.jpg
https://i56.tinypic.com/2lnwa69.jpg


If the nuts slide against each other, than they are not sufficiently tighten. I used a bolt with the strength of 8.8. The head of a weaker bolt might have been deformed. https://www.roymech.co.uk/Useful_Tabl...s/Strength.htm is a table with the strength of bolts. I think this method can be used to remove other types of freewheels. In my case the freewheel splines are intact, but the bolt head was deformed.

Last edited by spm40; 09-29-10 at 01:49 AM.
spm40 is offline  
Old 09-29-10, 12:29 PM
  #278  
aka Tom Reingold
 
noglider's Avatar
 
Join Date: Jan 2009
Location: New York, NY, and High Falls, NY, USA
Posts: 40,691

Bikes: 1962 Rudge Sports, 1971 Raleigh Super Course, 1971 Raleigh Pro Track, 1974 Raleigh International, 1975 Viscount Fixie, 1982 McLean, 1996 Lemond (Ti), 2002 Burley Zydeco tandem

Mentioned: 510 Post(s)
Tagged: 0 Thread(s)
Quoted: 7287 Post(s)
Liked 2,362 Times in 1,381 Posts
What unusual tools or supplies do you like to carry on the road for unanticipated repairs? I've heard of pieces of cut-up inner tube, lengths of duct tape, lengths of wire...

What else?
__________________
Tom Reingold, tom@noglider.com
New York City and High Falls, NY
Blogs: The Experienced Cyclist; noglider's ride blog

“When man invented the bicycle he reached the peak of his attainments.” — Elizabeth West, US author

Please email me rather than PM'ing me. Thanks.
noglider is offline  
Old 10-02-10, 05:06 PM
  #279  
Senior Member
 
rpenmanparker's Avatar
 
Join Date: Dec 2009
Location: Houston, TX
Posts: 28,682

Bikes: 1990 Romic Reynolds 531 custom build, Merlin Works CR Ti custom build, super light Workswell 066 custom build

Mentioned: 109 Post(s)
Tagged: 1 Thread(s)
Quoted: 6556 Post(s)
Likes: 0
Liked 58 Times in 36 Posts
When building wheels with very light gauge spokes like DT Revolutions, spoke windup can be a real pain. There are tools to hold the spoke from rotating, but usually good technique (overturning the nipple then backing off) will avoid the windup. The trick is to see the twist. I use "flags" made out of short strips of masking tape stuck to each spoke about in the middle of the length. If you line these up on every spoke all facing in the direction of the rotation of the wheel or all across the rotation direction, it is easy to see when a spoke is turning and correct the twist. I got the idea from building a wheel with aero spokes which act as their own indicators of twist. You can easily see when the flat of the aero spoke is not facing forward. So I figured I could make a simialr indicator for round spokes out of the masking tape. Hope this helps.
rpenmanparker is offline  
Old 10-02-10, 06:44 PM
  #280  
aka Tom Reingold
 
noglider's Avatar
 
Join Date: Jan 2009
Location: New York, NY, and High Falls, NY, USA
Posts: 40,691

Bikes: 1962 Rudge Sports, 1971 Raleigh Super Course, 1971 Raleigh Pro Track, 1974 Raleigh International, 1975 Viscount Fixie, 1982 McLean, 1996 Lemond (Ti), 2002 Burley Zydeco tandem

Mentioned: 510 Post(s)
Tagged: 0 Thread(s)
Quoted: 7287 Post(s)
Liked 2,362 Times in 1,381 Posts
That's excellent! I'll try it. I guess post-it flags would work, too, but they would cost more.
__________________
Tom Reingold, tom@noglider.com
New York City and High Falls, NY
Blogs: The Experienced Cyclist; noglider's ride blog

“When man invented the bicycle he reached the peak of his attainments.” — Elizabeth West, US author

Please email me rather than PM'ing me. Thanks.
noglider is offline  
Old 11-03-10, 12:37 PM
  #281  
Senior Member
 
joejack951's Avatar
 
Join Date: May 2004
Location: Wilmington, DE
Posts: 12,098

Bikes: 2016 Hong Fu FM-079-F, 1984 Trek 660, 2005 Iron Horse Warrior Expert, 2009 Pedal Force CX1, 2016 Islabikes Beinn 20 (son's)

Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 1240 Post(s)
Liked 94 Times in 65 Posts
For my sanity, please don't credit the above spammer with the tip he posted. It's a cut and paste from page 1 of a post I made over 3 years ago. I've reported the post as spam.
joejack951 is offline  
Old 11-03-10, 12:49 PM
  #282  
Throw the stick!!!!
 
LowCel's Avatar
 
Join Date: Apr 2003
Location: Charleston, WV
Posts: 18,150

Bikes: GMC Denali

Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 176 Post(s)
Liked 92 Times in 31 Posts
Originally Posted by joejack951
For my sanity, please don't credit the above spammer with the tip he posted. It's a cut and paste from page 1 of a post I made over 3 years ago. I've reported the post as spam.
Thanks for the report, spammer is no longer among us.
__________________
I may be fat but I'm slow enough to make up for it.
LowCel is offline  
Old 11-06-10, 03:34 AM
  #283  
Newbie
 
Join Date: Jul 2010
Location: Seattle, WA
Posts: 4

Bikes: 1986 Schwinn Passage, 80's Takara SS/Fixed

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Cold Weld for braze-ons and other attachments

I have a tutorial on my blog for repairing broken braze-ons and eyelets at home for under $6. This process works for pretty much any frame material.click here
passage86 is offline  
Old 11-06-10, 11:37 AM
  #284  
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,935

Bikes: Several, mostly not name brands.

Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3571 Post(s)
Liked 3,367 Times in 1,916 Posts
Originally Posted by passage86
I have a tutorial on my blog for repairing broken braze-ons and eyelets at home for under $6. This process works for pretty much any frame material.click here
Looks pretty good. If you pass e.g. a piece of welding rod through the intact braze on and into the other side, it can hold the repair in proper alignment while the epoxy dries.
JohnDThompson is offline  
Old 11-12-10, 10:30 AM
  #285  
Friendship is Magic
 
3alarmer's Avatar
 
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,932

Bikes: old ones

Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26247 Post(s)
Liked 10,229 Times in 7,098 Posts
This is a cut and paste from a recent stuck cotter
thread. I did not invent this, but honestly don't
recall where or when or from whom I learned it.
Somewhere in the vast Internet universe somewhere
I think. If it is out of place, let me know and I will
remove it:


I've had pretty good luck lately on several cottered
cranks with fairly old and rusty cotters by using a
twenty dollar drill press vise as the press with a
9/16 ( or thereabouts) socket as the negative space.

First you oil up the buggers with Triflow, PB Blaster
(as seen on TV), or your favorite penetrating oil,
having loosened the nuts to provide access for
squirting the oil. Now the hard part .. wait ten
of fifteen minutes for the magic of chemistry to
do its thing. Leave the nuts on, but with about
an eighth to a quarter inch of space so the cotter
can move as you press it.

Put the drill press vise on the crank with one face
pressing on the nutted pin end, and the socket
on the other face to provide negative space for
the pin to move into. Crank it down hard .. wait,
crank it down hard again.. wait again. They usually
pop free by about the third application of force.

You may need to put a short cheater on the drill
press vise handle as they are too short to provide
much leverage. Make sure the vice screw is well oiled
or greased.

These are readily available at Home Depot or any
of the chinese tool import places. They work as well
as specialty cotter presses at a fraction of the price.

I have hammered out a few over the years and always
found it to be a somewhat risky and problematic
procedure. This works better, although I am forced
to agree with Tom and Bikeman that it is not nearly
as satisfying as pounding on something with a hammer.



Mike Larmer

Last edited by 3alarmer; 11-12-10 at 10:30 AM. Reason: Punctuation
3alarmer is online now  
Old 11-22-10, 12:15 PM
  #286  
Sir Fallalot
Thread Starter
 
wroomwroomoops's Avatar
 
Join Date: Jul 2006
Posts: 5,286
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 9 Post(s)
Likes: 0
Liked 13 Times in 11 Posts
Dear moderators:

I started this thread a few years back, hoping it would be a valuable resource for cyclists, with all sorts of neat tricks that would augment one's bicycle mechanics arsenal of knowledge.

It seems that the seed has borne fruits - and so, the "(hopefully)" is not anymore necessary.


Could you please edit the title of the thread so that "(hopefully)" doesn't feature anymore?




Thanks,



mario/wroomwroomoops
wroomwroomoops is offline  
Old 11-22-10, 02:20 PM
  #287  
Senior Member
 
CbadRider's Avatar
 
Join Date: Sep 2008
Location: On the bridge with Picard
Posts: 5,935

Bikes: Specialized Allez, Specialized Sirrus

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 17 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by wroomwroomoops
Dear moderators:

I started this thread a few years back, hoping it would be a valuable resource for cyclists, with all sorts of neat tricks that would augment one's bicycle mechanics arsenal of knowledge.

It seems that the seed has borne fruits - and so, the "(hopefully)" is not anymore necessary.


Could you please edit the title of the thread so that "(hopefully)" doesn't feature anymore?




Thanks,



mario/wroomwroomoops
Done.
__________________
Originally Posted by Xerum 525
Now get on your cheap bike and give me a double century. You walking can of Crisco!!

Forum Guidelines *click here*
CbadRider is offline  
Old 12-22-10, 10:31 AM
  #288  
Junior Member
 
slide23's Avatar
 
Join Date: Nov 2007
Location: Portland OR
Posts: 129
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by rs1101
tire wont seat correctly on your old rims? spray some pledge or simple green along the bead!
Do not use Simple Green on aluminum. It attacks aluminum. If you absolutely must use SG on aluminum, there is a version specifically formulated for such use, Simple Green Aircraft if I recall correctly.
slide23 is offline  
Old 12-22-10, 11:03 AM
  #289  
Junior Member
 
slide23's Avatar
 
Join Date: Nov 2007
Location: Portland OR
Posts: 129
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by Mr Zippy
Put a few disposable hand /wet/alcohol based wipes/sachets (i.e. the sealed ones you get from fast food restaurants that have a chemical smell) in your saddle bag, to use clean your hands if you have to put your chain back on the gears, or after any other dirty work you might need to do on a ride.

Unfortunately I worked this out the hard way yesterday, and my white handle bar tape now isn't as white as it used to be.
Don't get the grease on you in the first place. Pack a bunch of latex gloves in your repair bag. Put them in a ziploc bag so that nothing in your toolkit pokes holes in them. They compress down to nothing.

And when you're done working on the bike on the roadside, the gloves serve well as a trash container: hold whatever dirty/greasy/nasty garbage in your hand and pull the glove off, turning it inside-out over the trash. Repeat with the other hand. Now it won't funkify your toolbag either.
slide23 is offline  
Old 01-05-11, 08:25 PM
  #290  
Lost Again
 
gitarzan's Avatar
 
Join Date: Jul 2009
Location: Columbus, Oh!
Posts: 1,044

Bikes: Soma Saga, 1991 Sirrus, Specialized Secteur Elite, Miele Umbria Elite.

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 2 Times in 2 Posts
Found this on the web.
https://bike.shimano.com/publish/cont...ty%20Chart.pdf

I found it useful.
gitarzan is offline  
Old 01-05-11, 10:36 PM
  #291  
aka Tom Reingold
 
noglider's Avatar
 
Join Date: Jan 2009
Location: New York, NY, and High Falls, NY, USA
Posts: 40,691

Bikes: 1962 Rudge Sports, 1971 Raleigh Super Course, 1971 Raleigh Pro Track, 1974 Raleigh International, 1975 Viscount Fixie, 1982 McLean, 1996 Lemond (Ti), 2002 Burley Zydeco tandem

Mentioned: 510 Post(s)
Tagged: 0 Thread(s)
Quoted: 7287 Post(s)
Liked 2,362 Times in 1,381 Posts
Wow, that's complicated.
__________________
Tom Reingold, tom@noglider.com
New York City and High Falls, NY
Blogs: The Experienced Cyclist; noglider's ride blog

“When man invented the bicycle he reached the peak of his attainments.” — Elizabeth West, US author

Please email me rather than PM'ing me. Thanks.
noglider is offline  
Old 01-29-11, 12:05 PM
  #292  
Friendship is Magic
 
3alarmer's Avatar
 
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,932

Bikes: old ones

Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26247 Post(s)
Liked 10,229 Times in 7,098 Posts
Originally Posted by gitarzan
Found this on the web.
https://bike.shimano.com/publish/cont...ty%20Chart.pdf

I found it useful.
Thanks. Incredibly valuable and, of course
it goes without saying, absolutely insane.

That one company could smilingly offer such
a wide range of confusion in interchangeability
says volumes about where we find ourselves
these days in Bicycle World.
__________________
3alarmer is online now  
Old 01-31-11, 06:26 PM
  #293  
Godbotherer
 
dwellman's Avatar
 
Join Date: Jan 2011
Location: Hermitage, TN
Posts: 1,322

Bikes: 1986 Cannondale SR300 (full SRAM Apex) 1996 Cannondale R800 (Full SRAM Rival), 1997 Cannondale R200 (Shimano Tiagra), 2012 Cannondale CAAD 10-5, 1992 Bridgestone RB-1 (SRAM Force)

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Cosmetic tip:

I found the grey/white-ish scuff marks in my saddle (badly scuffed) a bit annoying. If the leather is black (as in my case), you can "dye" the off-color leather with a black permanent marker and follow up with a leather wipe such as Weiman.
dwellman is offline  
Old 02-01-11, 08:23 PM
  #294  
Cottered Crank
 
Amesja's Avatar
 
Join Date: Aug 2010
Location: Chicago
Posts: 3,493

Bikes: 1954 Raleigh Sports 1974 Raleigh Competition 1969 Raleigh Twenty 1964 Raleigh LTD-3

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Likes: 0
Liked 11 Times in 7 Posts
Originally Posted by noglider
That's excellent! I'll try it. I guess post-it flags would work, too, but they would cost more.
Silk rag. Packs SMALL and light for a large rag. It makes cleaning up after a roadside repair job easier. I also carry a "wet nap" alcohol wipe for the times when you get even greasier than just patching a tube.

A silk rag can be made out of an old silk blouse. If you don't have an old silk blouse that you need to throw away then buy a whole silk shirt from Goodwill, Salvation Army, or other resale shop for $2 and re-purpose it. You can make at least a half-dozen rags out of a $2 blouse -more if it was a size 20 blouse...
Amesja is offline  
Old 02-10-11, 05:19 PM
  #295  
Junior Member
 
Join Date: Feb 2011
Posts: 23
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
My bike didn't come with reflectors on the front and back, so after a snowplow knocked some off of the road, I took them and pried the reflector bits off of their cases and glued them onto my bike. They've since fallen off, but if I you use a better adhesive than Dollar Tree superglue, it makes a great free repair.
Feral Slug is offline  
Old 02-10-11, 07:48 PM
  #296  
Godbotherer
 
dwellman's Avatar
 
Join Date: Jan 2011
Location: Hermitage, TN
Posts: 1,322

Bikes: 1986 Cannondale SR300 (full SRAM Apex) 1996 Cannondale R800 (Full SRAM Rival), 1997 Cannondale R200 (Shimano Tiagra), 2012 Cannondale CAAD 10-5, 1992 Bridgestone RB-1 (SRAM Force)

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by Feral Slug
My bike didn't come with reflectors on the front and back,
I've used 3M reflective tape (r.g Conspicuity Film / Scotchlite. . also marketed as "Sidelights" in the early to mid 1990's). Not as good as a real light, but pretty good.
dwellman is offline  
Old 02-10-11, 08:11 PM
  #297  
Junior Member
 
Join Date: Feb 2011
Posts: 23
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I debated on getting some reflective tape, but then I realized that I hardly ever ride in the dark so I didn't want to pay for it.
Feral Slug is offline  
Old 02-13-11, 12:45 AM
  #298  
Senior Member
 
Captain Blight's Avatar
 
Join Date: Oct 2009
Location: Minneapolis
Posts: 2,473

Bikes: -1973 Motobecane Mirage -197? Velosolex L'Etoile -'71 Raleigh Super Course

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times in 2 Posts
(1) Set properly-toed brake pads very close to a very true rim, and 90% of brake problems go away

(2) Cable tension is what actually moves the derailleur, and the derailleur will move just as far as the shifter tells it to

(3) Pre-load bearings slightly (ca. 10% of expected load) when setting cups, cones, etc.

(4) If all you're doing is enduring, you're not enjoying

(5) keep it clean.
Captain Blight is offline  
Old 02-14-11, 09:11 AM
  #299  
Peripheral Visionary
 
spock's Avatar
 
Join Date: Oct 2008
Location: Jax, FL
Posts: 1,157
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 5 Times in 5 Posts
My tire levers



Works like a charm. I use the smooth side, and yes those are from forks (or spoons, don't remember)
spock is offline  
Old 02-16-11, 10:29 AM
  #300  
Member
 
Join Date: Dec 2009
Posts: 41
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Vertical drops and fixed gear do not a happy bike make - my tip is forget about the imprecise half links, and skid-free tensioners/derailers, either suck it up and find a framebuilder to change your drops or get a new frame!
j-quix is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.