Quill stem & steerer tube problem
08-21-07, 01:16 AM
#1
Senior Member
Thread Starter
Join Date: Jul 2007
Posts: 1,039
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 75 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Quill stem & steerer tube problem
I got a Nitto Technomic Deluxe stem today and am having some trouble with it. I can only get it in to about the minimum insertion mark. The original stem will go in farther. I figured that maybe I had slightly bulged the steerer tube or something, but seeing the thread on tapered steerer tubes makes me wonder if that is what is coming into play. The wedge of the original stem is shorter overall and rounded at the bottom while the Nitto's is more squared off. The short side of the original wedge is also very short while the Nitto's short side is maybe .75 cm. Wish I'd seen the tapered steerer tube thread earlier because I've already taped up the handlebar. Are wedges interchangeable between stems? I didn't think to try the wedge from the original stem on the Nitto stem, so I don't know if it would make a difference anyway, but if it's safe to switch them I'll give it a try.
Last edited by Pendergast; 08-21-07 at 01:50 AM.
08-21-07, 06:55 AM
#2
Senior Member
Can you see down inside the steerer tube with a flashlight? There might be a bunch of corrosion/crud inside that had built up right below the wedge on the old stem. You could probably get in there with some sand paper or even a bearing scraper and remove the corrosion/crud.
Before swapping wedges, measure the angle on the wedge and the stem and make sure they match up like the original combo did. This will be an easy task if you have an optical comparator available but you could probably get a decent estimate with a protractor.
Before swapping wedges, measure the angle on the wedge and the stem and make sure they match up like the original combo did. This will be an easy task if you have an optical comparator available but you could probably get a decent estimate with a protractor.
08-21-07, 04:50 PM
#3
Senior Member
Join Date: May 2005
Location: La La Land (We love it!)
Posts: 6,301
Bikes: Gilmour road, Curtlo road; both steel (of course)
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 273 Post(s)
Likes: 0
Liked 10 Times
in
9 Posts
An optical comparitor..?
__________________
Today, I believe my jurisdiction ends here...
Today, I believe my jurisdiction ends here...
08-21-07, 06:54 PM
#4
Senior Member
But, I'd hate to see a half to 1 degree angle difference that someone missed using the eyeball method ruin the guy's steerer tube. I just happen to have a comparator readily available at work so the suggestion came naturally. I realize not everyone has these things around though.
08-21-07, 09:22 PM
#5
Senior Member
Join Date: Dec 2005
Location: Boulder, Colorado
Posts: 1,383
Bikes: Cinelli Supercoursa 69, Ritchey Breakaway Cross, Mondonico Diamond Extra 05, Coors Light Greg Lemond (built by Scapin) 88, Scapin MTB, Stumpjumper 83, Specialized Stumpjumper M4, Lemond Poprad 2001
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Liked 2 Times
in
1 Post
You know, you have a good point considering I did suggest eyeballing the angle using a protractor But, I'd hate to see a half to 1 degree angle difference that someone missed using the eyeball method ruin the guy's steerer tube. I just happen to have a comparator readily available at work so the suggestion came naturally. I realize not everyone has these things around though.
But, I'd hate to see a half to 1 degree angle difference that someone missed using the eyeball method ruin the guy's steerer tube. I just happen to have a comparator readily available at work so the suggestion came naturally. I realize not everyone has these things around though.