trek 920 chainring removal
#1
Junior Member
Thread Starter
Join Date: Nov 2007
Posts: 8
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
trek 920 chainring removal
Hi All,
I just got myself an old (but don't know how old) Trek 920. It just seems like a sturdy little bike that I want to use for around town biking. It looks like it hasn't been maintained at all, so it requires a firm cleaning, and perhaps some new parts here and there. I'm not very familiar with mountain bikes (I road bike mostly) and kind of got stuck on the chainring removal.
It seems like the chainrings are stamped together, and there aren't just a couple of bolts I can remove to take them off (like on my road bike). Seems like I first need to remove the cranks to get to the chainrings? True? Does anybody know what type of crankset is fitted on the trek 920? What type of crankpuller do I need (if I need one)? In other words, how do I remove these chainrings???
I don't know what year the bike is, I estimate about 10 years old or so, and it's got the stx front and rear derailleur.
Not sure if I can post pics, but if yes, I'll try to make one, so that you can perhaps see what I mean.
Thanks for any input, appreciate it!
Tim
I just got myself an old (but don't know how old) Trek 920. It just seems like a sturdy little bike that I want to use for around town biking. It looks like it hasn't been maintained at all, so it requires a firm cleaning, and perhaps some new parts here and there. I'm not very familiar with mountain bikes (I road bike mostly) and kind of got stuck on the chainring removal.
It seems like the chainrings are stamped together, and there aren't just a couple of bolts I can remove to take them off (like on my road bike). Seems like I first need to remove the cranks to get to the chainrings? True? Does anybody know what type of crankset is fitted on the trek 920? What type of crankpuller do I need (if I need one)? In other words, how do I remove these chainrings???
I don't know what year the bike is, I estimate about 10 years old or so, and it's got the stx front and rear derailleur.
Not sure if I can post pics, but if yes, I'll try to make one, so that you can perhaps see what I mean.
Thanks for any input, appreciate it!
Tim
#2
Spin Forest! Spin!
Join Date: Sep 2007
Location: Arrid Zone-a
Posts: 5,956
Bikes: I used to have many. And I Will again.
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 11 Times
in
10 Posts
If it's a stamped crank, you can't disassemble the chainrings.
Low-cost cranks are stamped units usually. Once the teeth wear out, you toss it.
Low-cost cranks are stamped units usually. Once the teeth wear out, you toss it.
#4
Junior Member
Thread Starter
Join Date: Nov 2007
Posts: 8
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Ok, thanks a lot guys! That explains it! I'll toss it then.
So do you perhaps know what types of crankset I can get for this type of bike? In other words how do I measure if it's gonna be compatible with the bottom bracket. Preferably inexpensive, but I do want removable chainrings this time.
Also, what type of crankpuller do I need to remove this crank?
I will post a picture later today.
So do you perhaps know what types of crankset I can get for this type of bike? In other words how do I measure if it's gonna be compatible with the bottom bracket. Preferably inexpensive, but I do want removable chainrings this time.
Also, what type of crankpuller do I need to remove this crank?
I will post a picture later today.
#5
Spin Forest! Spin!
Join Date: Sep 2007
Location: Arrid Zone-a
Posts: 5,956
Bikes: I used to have many. And I Will again.
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 11 Times
in
10 Posts
Chances are you have either a Shimano Alivio, or Suntour XC-E stamped crank utilizing a square taper bottom bracket.
Check Sheldon Brown's/Harris Cyclery site for bottom bracket spindle length info once you've verified the model. Then you can check if a new crank will work with the old BB.
Personally, I'd buy a new matching BB for the new crank.
Check out Nashbar.com for some deals.
I picked up a Shimano FC-M340 triple crankset for $10 new. It is steel rings, but are bolted to an alumimum spider.
You need a thread-on crankarm puller.
Go to Park Tool site for pics and how-to info.
Check Sheldon Brown's/Harris Cyclery site for bottom bracket spindle length info once you've verified the model. Then you can check if a new crank will work with the old BB.
Personally, I'd buy a new matching BB for the new crank.
Check out Nashbar.com for some deals.
I picked up a Shimano FC-M340 triple crankset for $10 new. It is steel rings, but are bolted to an alumimum spider.
You need a thread-on crankarm puller.
Go to Park Tool site for pics and how-to info.
#6
Junior Member
Thread Starter
Join Date: Nov 2007
Posts: 8
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Chances are you have either a Shimano Alivio, or Suntour XC-E stamped crank utilizing a square taper bottom bracket.
Check Sheldon Brown's/Harris Cyclery site for bottom bracket spindle length info once you've verified the model. Then you can check if a new crank will work with the old BB.
Personally, I'd buy a new matching BB for the new crank.
Check out Nashbar.com for some deals.
I picked up a Shimano FC-M340 triple crankset for $10 new. It is steel rings, but are bolted to an alumimum spider.
You need a thread-on crankarm puller.
Go to Park Tool site for pics and how-to info.
Check Sheldon Brown's/Harris Cyclery site for bottom bracket spindle length info once you've verified the model. Then you can check if a new crank will work with the old BB.
Personally, I'd buy a new matching BB for the new crank.
Check out Nashbar.com for some deals.
I picked up a Shimano FC-M340 triple crankset for $10 new. It is steel rings, but are bolted to an alumimum spider.
You need a thread-on crankarm puller.
Go to Park Tool site for pics and how-to info.
I added a picture of the bottom bracket and the cranks/chainrings as promised.
Now what do I measure on the bottom bracket to make sure I get the right one? The tapered squares are about 1.3 cm wide halfway, the frame width over the bb is 7.35 (with outer diameter of the cylinder holding the BB roughly 4.09 cm). Measured across the end of the square tapered pins I have 11.38cm. Apart from the measurement of the ends of the square pins, I doubt whether these measures have any universal meaning.
Anyway, maybe the picture will help here. If I measures irrelevant measures (which is more than likely), please let me know what to be measuring before I order new parts.
Thanks again guys!
Tim
#7
Junior Member
Thread Starter
Join Date: Nov 2007
Posts: 8
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Ok, did a little quick reading on the matter (sorry, should have done that before).
I realize now that the distance across the square tapered pins that I measured is the spindle length, right? Can anybody tell from the picture in the previous post whether this is a shimano cardridge-style bb? I've been looking at some pictures and drawings and that's what it looks like the most. But there seem to be so many different kinds that I am not positive.
So what tools do I need to succesfully remove this BB and install a new one? Any suggestions on what I should get (inexpensive) is great!
Thanks again!
I realize now that the distance across the square tapered pins that I measured is the spindle length, right? Can anybody tell from the picture in the previous post whether this is a shimano cardridge-style bb? I've been looking at some pictures and drawings and that's what it looks like the most. But there seem to be so many different kinds that I am not positive.
So what tools do I need to succesfully remove this BB and install a new one? Any suggestions on what I should get (inexpensive) is great!
Thanks again!
#8
Really Old Senior Member
Is there actually anything wrong with the current BB / chain rings.
#9
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times
in
741 Posts
Right, they are a "use it up and discard" component. A conventional crank puller works to remove the entire crank from the bb spindle but after than there is no service other than cleaning.
#10
Junior Member
Thread Starter
Join Date: Nov 2007
Posts: 8
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Open to suggestions though!
Anybody identified the type of BB in the picture?
Tim
#11
Really Old Senior Member
It appears to be a standard cartridge type-
https://sheldonbrown.com/harris/botto...s.html#shimano
https://sheldonbrown.com/harris/botto...s.html#shimano
#12
Spin Forest! Spin!
Join Date: Sep 2007
Location: Arrid Zone-a
Posts: 5,956
Bikes: I used to have many. And I Will again.
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 11 Times
in
10 Posts
That looks like a Shimano BB and crank. You require a splined cup tool: Shimano TL-UN74-S
All the major bike tool makers have a compatible tool available as well.
The spindle length is dependent on the model crank to be used. So, if you buy Crank X, it'll require BB Y for an English spec BB shell. Or BB Z for an Italian spec BB shell. etc.
All the major bike tool makers have a compatible tool available as well.
The spindle length is dependent on the model crank to be used. So, if you buy Crank X, it'll require BB Y for an English spec BB shell. Or BB Z for an Italian spec BB shell. etc.