Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Sqeaky brakes

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Sqeaky brakes

Old 01-19-08, 01:03 PM
  #1  
Senior Member
Thread Starter
 
Join Date: Dec 2007
Posts: 100
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Sqeaky brakes

I have the avid shorty 6 contis with drop bar levers (tektros) and the front brakes squeal!! what is the best way to fix??
breaking away is offline  
Old 01-19-08, 01:39 PM
  #2  
Non Tribuo Anus Rodentum and off to the next adventure (RIP)
 
Stacey's Avatar
 
Join Date: Dec 2002
Posts: 9,161
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 2 Times in 2 Posts
You can clean the rim, sand and toe in the shoes. I've wondered if spoke tension might have something to do with it as well... sympathetic vibrations of the spokes and all that.

I've tried all the 'fixes'. A disc finally did it for me.
__________________
Stacey is offline  
Old 01-19-08, 01:57 PM
  #3  
Senior Member
 
graybeard's Avatar
 
Join Date: Jan 2008
Location: Ladysmith, (Vancouver Island) British Columbia
Posts: 59

Bikes: Surly Disc trucker, Surly Troll, Valence Carbon Road, Haro Zeon Dually, GT Dyno Criuser

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
maybe a fix

Always make sure rim is clean and no reside oil , waxes etc. Make sure pads are new enough to still be soft rubber and not dried out and hard. Generally a soft compound brake shoe is better than a cheaper hard compound. Also check to make sure the cantis do not have excess pivot wear. It is important that the shoe touch the rim with the leading (front) edge before the tail end when applying the brakes. If shoe is not toed in at the front by at least 1mm , it will usually squeal. Obviously, worn pivots on the cantis would exacerbate the problem by allowing the back of the shoe to hit rim harder than the front.
Good luck ,
graybeard is offline  
Old 01-19-08, 02:42 PM
  #4  
Senior Member
Thread Starter
 
Join Date: Dec 2007
Posts: 100
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
brakes

Whats the best way to toe in the shoe??
breaking away is offline  
Old 01-19-08, 02:49 PM
  #5  
cab horn
 
Join Date: Jun 2004
Location: Toronto
Posts: 28,353

Bikes: 1987 Bianchi Campione

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 42 Post(s)
Likes: 0
Liked 25 Times in 18 Posts
Originally Posted by breaking away
Whats the best way to toe in the shoe??
With your hand.

The other trick that nobody ever does unless it's a last resort is sanding a 45 degree trailing edge to the pad. That and gently sanding the rim down with sandpaper pressed up against the rim surface with the brakes on.

There is no squeak that cannot be fixed.
operator is offline  
Old 01-19-08, 04:02 PM
  #6  
Senior Member
 
onbike 1939's Avatar
 
Join Date: Dec 2004
Location: Fife Scotland
Posts: 2,053

Bikes: Airnimal Chameleon; Ellis Briggs; Moulton TSR27 Moulton Esprit

Mentioned: 37 Post(s)
Tagged: 0 Thread(s)
Quoted: 3291 Post(s)
Liked 827 Times in 583 Posts
My Tektros with soft pads squealed for months and nothing I could do would stop them. Eventually I took a rough file to the pads and this did the trick.
onbike 1939 is offline  
Old 01-19-08, 04:47 PM
  #7  
Triathlon in my future???
 
flip18436572's Avatar
 
Join Date: Jun 2007
Location: Southwest Iowa
Posts: 2,193

Bikes: Junk, that is why I am here. :-)

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Usually clean the rims and/or the pads. Filing the pads will sometimes fix it, and one person cut small grooves with a file across the pad to reduce the squeal.
__________________
2007 Jamis Ventura Comp
2006 Jamis Explorer 2.0
2000 Specialized Hardrock (bought used)
Swim, Bike, Run and sounds like fun
flip18436572 is offline  
Old 01-19-08, 04:50 PM
  #8  
♋ ☮♂ ☭ ☯
 
-=(8)=-'s Avatar
 
Join Date: Feb 2005
Location: 40205 'ViLLeBiLLie
Posts: 7,902

Bikes: Sngl Spd's, 70's- 80's vintage, D-tube Folder

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times in 2 Posts
How about disks ?
The front disks of my new bike sing like rubbing the rim of a wine glass
with wine on your finger.....Its driving me nuts
__________________
-ADVOCACY-☜ Radical VC = Car people on bikes. Just say "NO"
-=(8)=- is offline  
Old 01-19-08, 05:35 PM
  #9  
Senior Member
 
graybeard's Avatar
 
Join Date: Jan 2008
Location: Ladysmith, (Vancouver Island) British Columbia
Posts: 59

Bikes: Surly Disc trucker, Surly Troll, Valence Carbon Road, Haro Zeon Dually, GT Dyno Criuser

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
sqeeeelers

Sqealing disc brakes are usually caused by contaminated brake pads. Try cleaning the disc rotors with rubbing alcohol and a clean cloth. remove pads and make sure they are clean also, light wire brush and alcohol work well on pads also.
Check to make sure the caliper is centered and parallel to the rotor. Road test bike for sqeeeel.
One trick that sometimes helps is to take a water bottle and apply substantial water to the caliper on the road test while braking.
If all above fails , dig out a $20 bill and buy some new pads and instal . Always use caution when installing pads and working on disc brakes.. Be careful with fingers getting into the rotor ..ouch ouch..
As mentioned contamination is the cause 90 % of the time, so dont spray lubes , cleaners, waxes on your rotors/calipers. Using the coin op car wash is bad because so often there is wax in the hose when you first turn it on. Using spray chain lubes & spray waxes is also a problem. Washing your bike in the driveway with car wash soap can be bad as many Auto soaps also have a wax in them. The best soap to wash your bicycle with is blue" Dawn "dishwashing soap. (regular dish wash soaps have oil emolients in them to make hour hands soft and pretty. Doug Dye, (Cannondale N.W. sales Rep) recommended the blue Dawn years ago, and I use it all the time. it works.
good luck
graybeard is offline  
Old 01-19-08, 05:41 PM
  #10  
Senior Member
 
graybeard's Avatar
 
Join Date: Jan 2008
Location: Ladysmith, (Vancouver Island) British Columbia
Posts: 59

Bikes: Surly Disc trucker, Surly Troll, Valence Carbon Road, Haro Zeon Dually, GT Dyno Criuser

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
setting toe

I often use a shim inserted under the back of the shoe to hold it out the thickness I want. The more worn the calipers are the more toe in you need. Small piece of thin folded cardboard works well (Matchbook?) or used whatever you have handy. Get another person to squeeze the brakes on with the shim under the back of the pad , while you align and tighten. If you dont have a helper to hold on the brakes , use a big rubber band.( old inner tube cut up Etc)
graybeard is offline  
Old 01-19-08, 05:48 PM
  #11  
Non Tribuo Anus Rodentum and off to the next adventure (RIP)
 
Stacey's Avatar
 
Join Date: Dec 2002
Posts: 9,161
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 2 Times in 2 Posts
Originally Posted by -=£em in Pa=-
How about disks ?
The front disks of my new bike sing like rubbing the rim of a wine glass
with wine on your finger.....Its driving me nuts
In that case just jam your Converse between the seat tube and the back tire. With practice you'll be able to modulate braking force easily.
__________________
Stacey is offline  
Old 01-20-08, 10:30 PM
  #12  
Mad bike riding scientist
 
cyccommute's Avatar
 
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,251

Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones

Mentioned: 149 Post(s)
Tagged: 1 Thread(s)
Quoted: 6133 Post(s)
Liked 4,067 Times in 2,310 Posts
Originally Posted by graybeard
Always make sure rim is clean and no reside oil , waxes etc. Make sure pads are new enough to still be soft rubber and not dried out and hard. Generally a soft compound brake shoe is better than a cheaper hard compound. Also check to make sure the cantis do not have excess pivot wear. It is important that the shoe touch the rim with the leading (front) edge before the tail end when applying the brakes. If shoe is not toed in at the front by at least 1mm , it will usually squeal. Obviously, worn pivots on the cantis would exacerbate the problem by allowing the back of the shoe to hit rim harder than the front.
Good luck ,
In this case it's a probably not contamination. Avids are known wide and far as squealers even with new pads that have been properly toed. I've battled with mine to the point were I ditched them for a while. I had to go back to them but this time I used Kool Stop dual compound MTB brakes.



So far the problem has been solved. Even in cold weather, the brakes haven't squealed.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!



cyccommute is offline  
Old 01-20-08, 10:57 PM
  #13  
Senior Member
 
graybeard's Avatar
 
Join Date: Jan 2008
Location: Ladysmith, (Vancouver Island) British Columbia
Posts: 59

Bikes: Surly Disc trucker, Surly Troll, Valence Carbon Road, Haro Zeon Dually, GT Dyno Criuser

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Don't you just love all this good advise. Next time I'm going to try those dual compound pads. Sounds like they work. Let us know how it works for you.
Thanx
graybeard is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.