Handlebar Questions: disadvantages with using shims and cutting down bars
#1
Junior Member
Thread Starter
Join Date: Sep 2005
Posts: 17
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Handlebar Questions: disadvantages with using shims and cutting down bars
2 questions on the stock noah's arc-like bars set up on a Specialized Langster Seattle.
Are there any disadvantages to cutting down the bars a bit to fit my shoulder width a bit better? I like the idea of going thru busy downtown streets with narrower bars. However, I am not sure if this is psychological but sometimes, I feel like I am getting some decent shock absorption when I grip near the end of the bars now. By trimming an inch on the ends, would I lose some of that?
Secondly, does anyone know if there are disadvantages to mounting a 26mm bullhorns on a 31.8 stem with the appropriate shims (ie: Problem Solvers 26>31.8 shim). It'd be nice if I can switch up the bars depending on the type of riding that I'll be doing.
Thanks!
Are there any disadvantages to cutting down the bars a bit to fit my shoulder width a bit better? I like the idea of going thru busy downtown streets with narrower bars. However, I am not sure if this is psychological but sometimes, I feel like I am getting some decent shock absorption when I grip near the end of the bars now. By trimming an inch on the ends, would I lose some of that?
Secondly, does anyone know if there are disadvantages to mounting a 26mm bullhorns on a 31.8 stem with the appropriate shims (ie: Problem Solvers 26>31.8 shim). It'd be nice if I can switch up the bars depending on the type of riding that I'll be doing.
Thanks!
#2
Year-round cyclist
Join Date: Apr 2002
Location: Montréal (Québec)
Posts: 3,023
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
1. If they are comfortable, leave them that way. On the other hand, if you feel like you have the arms or elbows stretched too far apart, cut them. Cut only 1/4 inch at a time. Better be safe than sorry.
As for the width vs busy downtown streets :
– In theory, unless the bars are almost twice wider than your shoulders, your elbows will be slightly wider apart anyways.
– While I don't always agree to the all "purist" ideas of vehicular cycling, I think that cyclists need to drive their vehicle responsibly. Since we tend to find that we should keep away from the door zone (i.e. ride 3-4 ft away from parked cars) and from sewer grades, and that cars should pass at least 3 ft away, I generally don't squeeze in between cars unless it's safe and unless I have at least 6 ft of space to do it safely and predictably.
As for using a shim : it should be equally rigid, but the more surfaces there are, the more squeaking there will be.
As for the width vs busy downtown streets :
– In theory, unless the bars are almost twice wider than your shoulders, your elbows will be slightly wider apart anyways.
– While I don't always agree to the all "purist" ideas of vehicular cycling, I think that cyclists need to drive their vehicle responsibly. Since we tend to find that we should keep away from the door zone (i.e. ride 3-4 ft away from parked cars) and from sewer grades, and that cars should pass at least 3 ft away, I generally don't squeeze in between cars unless it's safe and unless I have at least 6 ft of space to do it safely and predictably.
As for using a shim : it should be equally rigid, but the more surfaces there are, the more squeaking there will be.
#3
Senior Member
Join Date: Mar 2005
Location: Pinole, CA, USA
Posts: 17,392
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 443 Post(s)
Likes: 0
Liked 27 Times
in
25 Posts
Why not just "choke up" on the bars until you find a width that feels good and cut them to that width. It seems silly to me to cut a bunch of 1/4" slices. Use the the piece you cut off of one side to mark for the cut on the other side. I've shortened a few bars. It doesn't hurt them.
I've used Nitto stainless steel shims with no problems and no noises, but never a shim as thick as you're talking about.
I've used Nitto stainless steel shims with no problems and no noises, but never a shim as thick as you're talking about.