Please help me out with a brake problem
#1
Senior Member
Thread Starter
Join Date: Apr 2008
Posts: 860
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 17 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Please help me out with a brake problem
Hello all - I finally bought my new bike, much thanks to advice I got on this forum. Well, the bike is new to me. It's a 2005 Kona Jake cyclocross bike that I bought used. It pretty much looks like a new bike and am told it has very low miles and has pretty much been sitting in a basement for a couple years.
When I bought it the tires were flat (back tube needed replacing) and the brakes and gears were loose (from disuse I assume). I dropped it off for a tune up and picked it up tonight. I should mention that although I very much want to learn how to tune up this bike myself, I just don't have the knowledge yet.
The components are all low-end, but passable stuff. Sora components and Avid Shorty 4 brakes. To me it is all bling because I'm not a pro. I thought I was stepping way up from my old bike. At least my old bike F-ing stopped.
So I just got back inside from what I thought was going to be a long first night of riding. Everything works great, except the stupid thing won't stop. The brake cables are tight, and if I really squeeze them there is plenty of room left between the brake levers and the bike handles. It's just that it feels like I'm pressing a hard piece of plastic (say, like a toothbrush handle) against the metal of my tire. It's like there is no friction.
What do I do? I want to enjoy my new bike but this is pretty much the one thing that I can't deal with. The streets around here are pretty busy.
Like I said before, I don't have much knowledge about the mechanics of bikes, I'm a noobie. I really would like to learn though. But I also spent my budget on the bike itself. Is this an expensive fix?
They are Avid Shorty 4 brakes. They also have the second pair of brakes on the front. Those are to help me transition from the apparently awesome mtn bike that I gave up for this.
That is all I know. Here is the bike: https://www.konaworld.com/shopping_ca...3&parentid=182
ANY help is appreciated. Even if it is just to log on and hurl an insult or two!
Thanks in advance!
-B
When I bought it the tires were flat (back tube needed replacing) and the brakes and gears were loose (from disuse I assume). I dropped it off for a tune up and picked it up tonight. I should mention that although I very much want to learn how to tune up this bike myself, I just don't have the knowledge yet.
The components are all low-end, but passable stuff. Sora components and Avid Shorty 4 brakes. To me it is all bling because I'm not a pro. I thought I was stepping way up from my old bike. At least my old bike F-ing stopped.
So I just got back inside from what I thought was going to be a long first night of riding. Everything works great, except the stupid thing won't stop. The brake cables are tight, and if I really squeeze them there is plenty of room left between the brake levers and the bike handles. It's just that it feels like I'm pressing a hard piece of plastic (say, like a toothbrush handle) against the metal of my tire. It's like there is no friction.
What do I do? I want to enjoy my new bike but this is pretty much the one thing that I can't deal with. The streets around here are pretty busy.
Like I said before, I don't have much knowledge about the mechanics of bikes, I'm a noobie. I really would like to learn though. But I also spent my budget on the bike itself. Is this an expensive fix?
They are Avid Shorty 4 brakes. They also have the second pair of brakes on the front. Those are to help me transition from the apparently awesome mtn bike that I gave up for this.
That is all I know. Here is the bike: https://www.konaworld.com/shopping_ca...3&parentid=182
ANY help is appreciated. Even if it is just to log on and hurl an insult or two!
Thanks in advance!
-B
#4
Senior Member
Join Date: May 2007
Posts: 703
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
No...many people seem to like the Kool Stop pads...
The Avid pads might have just gotten hard from age...even though they aren't all that old. Strange.
The Avid pads might have just gotten hard from age...even though they aren't all that old. Strange.
#5
Senior Member
Thread Starter
Join Date: Apr 2008
Posts: 860
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 17 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Ok, thanks for the responses. I'll pick up a new pair. Out of curiosity, road bikes stop like every other bike, correct? Meaning I should be able to lock them up if I want. This is my first road bike.
#6
Senior Member
Join Date: Jul 2007
Posts: 2,114
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
The Avids you have are fine.
What do you mean by this? You have two sets of brakes in the front? Are you trying to stop with only the rear brakes?
Originally Posted by bryoth
They also have the second pair of brakes on the front. Those are to help me transition from the apparently awesome mtn bike that I gave up for this.
#7
Senior Member
Thread Starter
Join Date: Apr 2008
Posts: 860
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 17 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Sorry, I should have been more clear on that. I have four brake levers. Two brifters on the drop bar and two of the "cyclocross" type on either side of the stem, on the flat part of the drop bars. I think I've heard them referred to as safety brakes, although I might be wrong about that.
#8
Senior Member
Join Date: Jul 2007
Posts: 2,114
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Ahh right, you have a cyclocross bike. Take the bike back to the shop that did the tune up. Those Avids should stop you just fine. Either they did not adjust the brakes well or something is wrong with the pads. That is if you are using the front brake to stop. I'm still not sure because I can't skid my front brake. Either I stop or do an endo, no skidding. The rear brake only, yes I can skid.
#9
Senior Member
Join Date: Mar 2008
Posts: 8,688
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 295 Times
in
222 Posts
Your front OTOH will go heavier, and the heavier it goes the more available friction you get.
For the average rider this means that you'll endo before the front breaks loose on a good surface. It's not really a loss though, since I don't think I've met anyone ready to claim that they could do a controlled front skid...
If you do manage to get the front to break loose(by careful positioning and/or riding on a slick/loose surface) you usually go down quite fast as it is terribly difficult to keep the front wheel horizontal while it's sliding.
#10
Senior Member
Join Date: Mar 2003
Location: Beaufort, South Carolina, USA and surrounding islands.
Posts: 8,521
Bikes: Cannondale R500, Motobecane Messenger
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 11 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
The brake pads need to be adjusted to get the proper mechanical advantage to allow them to work. You can have too much leverage, which will prevent the brakes from working.
#11
Hypoxic Member
Join Date: Oct 2005
Location: Colorado Springs
Posts: 545
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 2 Times
in
1 Post
I've had problems glazing Avid pads when stopping from high speeds down hills.
Light sanding may be a temporary solution if the pads aren't dried out. I've had
no problems with Kool Stops.
Light sanding may be a temporary solution if the pads aren't dried out. I've had
no problems with Kool Stops.
#12
Senior Member
Join Date: Apr 2007
Posts: 6,760
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 1109 Post(s)
Liked 1,200 Times
in
760 Posts
On the other hand, he paid good money for a tune up. If the quick fix above doesn't do it, take it back. In fact, I'd take it back anyway. They didn't do what you paid them to do.
Part of the tuneup should have been brakes, and all adjustments should have been tested by the mechanic with a quick spin around the parking lot. The brakes are the LAST thing any competent shop would fail to test - IMHO.
#13
Senior Member
Join Date: Apr 2008
Location: A Latvian in Seattle
Posts: 1,020
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
...
On the other hand, he paid good money for a tune up. If the quick fix above doesn't do it, take it back. In fact, I'd take it back anyway. They didn't do what you paid them to do.
Part of the tuneup should have been brakes, and all adjustments should have been tested by the mechanic with a quick spin around the parking lot. The brakes are the LAST thing any competent shop would fail to test - IMHO.
On the other hand, he paid good money for a tune up. If the quick fix above doesn't do it, take it back. In fact, I'd take it back anyway. They didn't do what you paid them to do.
Part of the tuneup should have been brakes, and all adjustments should have been tested by the mechanic with a quick spin around the parking lot. The brakes are the LAST thing any competent shop would fail to test - IMHO.
#14
Senior Member
Thread Starter
Join Date: Apr 2008
Posts: 860
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 17 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Yeah, unfortunately they didn't take the bike out for a spin. The pads had already glazed over apparently from disuse. I had sanded them down last night but didn't get very good results. I'm a little let down in that I live in Charlotte, NC which is a very corporate little city and I only go to the single privately owned bike shop that I can find. In fact I have been going to this same guy for nearly 20 years now and he's somehow managed to hang with BikeSource, Bicycle Sport, REI, Dick's, Bike Line and all the chains around here while still giving me tune-ups for only $30 (as opposed to the $100 Bike Sport quoted). Cool old Italian guy. His new mechanic was the one that apparently messed up. That and I need to learn to change my own brake pads I guess. I was sorry to see them drop the ball.
I like this guy so much that I didn't want to make waves. I brought it to a chain and had the pads replaced with some expensive Shimano pads. I'll pick up some Kool Stops next time. Of course the chain I went to shafted me on the price, but what can you do. Brakes work like a charm now. Well- as good as a cyclocross brakes are supposed to work it seems. Still can't stop on a dime but why would I have to I suppose? I'm not taking it downhill. And if my original bike store messes up again I'll take it up with them.
Thanks for all the advice! One more thing I know about my bike.
-B
I like this guy so much that I didn't want to make waves. I brought it to a chain and had the pads replaced with some expensive Shimano pads. I'll pick up some Kool Stops next time. Of course the chain I went to shafted me on the price, but what can you do. Brakes work like a charm now. Well- as good as a cyclocross brakes are supposed to work it seems. Still can't stop on a dime but why would I have to I suppose? I'm not taking it downhill. And if my original bike store messes up again I'll take it up with them.
Thanks for all the advice! One more thing I know about my bike.
-B
#15
Senior Member
Join Date: May 2007
Posts: 703
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Did you get the Jake on craigslist? I'm up in Salisbury, I remember seeing a Jake posted on the Charlotte CL...
Kind of strange that the brakes still aren't stopping very well...
Kind of strange that the brakes still aren't stopping very well...
#17
Senior Member
Thread Starter
Join Date: Apr 2008
Posts: 860
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 17 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Yeah, I got the Jake on craigslist. That's cool that you recognize the ad. I paid $400 ultimately, which I thought was a pretty good deal, minus the tuneup and new brake pads required. It's an allright bike, especially for a beginner like myself.