KMC missing link connector
#1
Senior Member
Thread Starter
Join Date: Jul 2008
Location: Indiana
Posts: 166
Bikes: 85 Fuso, 86 Peloton, 84,88 Paramount
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
KMC missing link connector
I am trying to install a KMC chain with a 'missing link' connector. This one has both pins attached to one side plate and the other side of it is an oval shaped connector that is supposed to somehow slide onto the pins on the other side. It does not seem to me that the oval connector is long enough to slide on and over the pins. What's the trick ???? I have used the ones where there is one pin on each side plate and you squeeze them together to release, this one is definitely different.
#3
Elitist Troglodyte
Join Date: Jun 2006
Location: Dallas
Posts: 6,925
Bikes: 03 Raleigh Professional (steel)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
The face of the connector shown in the pic above should be facing outward.
__________________
Stupidity got us into this mess - why can't it get us out?
- Will Rogers
Stupidity got us into this mess - why can't it get us out?
- Will Rogers
#4
Full Member
Join Date: May 2008
Location: Tampa
Posts: 311
Bikes: Gunnar Sport 105/UDi2, previous: Lambert, Giant FCR3, Cannondale Synapse Carbon 105, Specialized Roubaix SL4 Comp UDi2
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 29 Post(s)
Likes: 0
Liked 18 Times
in
11 Posts
Here is how I did it. Put the plate with the two attached pins through the two ends of the chain. On the loose flat plate side of the “missing link,” note that there is a slightly wider part of the slot that is big enough for a pin to go through. Next take the flat piece of the “missing link” and put it over one of the pins on the part of the missing link that you have used to join the chain. Then slide the flat plate all the way down the slot so that the pin you put through is on the opposite end of the slot part that is enlarged. Grasp the chain and slightly bend the “missing link” so the ends of its pins move slightly closer to each other. Move the slotted plate so the other pin goes through the enlarged portion of the slot. Finally, grab the chain and bend it back the other way so the two pins of the “missing link” are at the extreme ends of the slot.
#5
cab horn
Join Date: Jun 2004
Location: Toronto
Posts: 28,353
Bikes: 1987 Bianchi Campione
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 42 Post(s)
Likes: 0
Liked 26 Times
in
19 Posts
I am trying to install a KMC chain with a 'missing link' connector. This one has both pins attached to one side plate and the other side of it is an oval shaped connector that is supposed to somehow slide onto the pins on the other side. It does not seem to me that the oval connector is long enough to slide on and over the pins. What's the trick ???? I have used the ones where there is one pin on each side plate and you squeeze them together to release, this one is definitely different.
#7
Senior Member
Thread Starter
Join Date: Jul 2008
Location: Indiana
Posts: 166
Bikes: 85 Fuso, 86 Peloton, 84,88 Paramount
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Not a SS -this is going on an 86 Paramount with a 6 speed freewheel. The 'trick' appears to be that my side plate with the two pins is bent so the pins angle out slightly. I have not tried to straighten it out but certainly seems to be the reason it doesn't fit.
#8
Senior Member
Join Date: Apr 2008
Posts: 93
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
That's intentional. You put in one pin through the hole in the oval, slide and then rotate the oval so that the hole in the oval lines up near the other pin, and then bend the opposite direction (bring the pins closer together) to get it to snap in place. Once you let go the spring in the pin-plate spreads them again and you're gold.
#9
Senior Member
Join Date: Apr 2008
Location: Maidstone, Kent, England
Posts: 2,637
Bikes: 1970 Holdsworth Mistral, Vitus 979, Colnago Primavera, Corratec Hydracarbon, Massi MegaTeam, 1935 Claud Butler Super Velo, Carrera Virtuoso, Viner, 1953 Claud Butler Silver Jubilee, 1954 Holdsworth Typhoon, 1966 Claud Butler Olympic Road, 1982 Claud
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 10 Post(s)
Liked 11 Times
in
10 Posts
+1, You said it before I saw the post! These are good connectors!