balance tires
#1
Junior Member
Thread Starter
Join Date: Sep 2002
Posts: 23
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
balance tires
does anyone know how to balance a tire. When I spin the tire it makes the whole bike move up and down. Is there a certain way to mount the tire on the rim so it is balanced?
Thanks Mike
Thanks Mike
#2
hello
Firstly, is your rim completely true and round? I usually find that a rim with a high or low spot will cause an unbalance when spun at a high rate. As for tires, I don't know if there's anything much you could do about them.
George
George
#3
Senior Member
Join Date: Feb 2004
Location: Cleveland, OH
Posts: 2,304
Bikes: 2004 Trek 4600 SS, 2016 Cannondale Cujo 2 SS
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 13 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
What kind of tire? Knobbie, slick? It could have a flat spot from skidding. Other than that, i dunno
#4
Senior Member
Join Date: Oct 2002
Posts: 217
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
As George said, check the rim-take the tire and tube off and see if that is the problem. If it is not the rim, it could be the tube. If the tube is not the right size for the rim, or if it is stretched and somehow doubled over, it would push the tire up. Befor this though, check first whether the bead of the tire ( the part that should set into the rim wall) is uniformly set in all around the wheel. If it is not, deflate it, and set it properly, and re-inflate. If it pushes the bead out again, see if the tube is correct and not out of shape. If the tube is not out of shape, and if the bead keeps coming out, it is either the tire or the rim with a faulty side wall.
#5
Elitist Jackass
Join Date: Oct 2003
Location: Georgia
Posts: 3,262
Bikes: Cannondale 2.8, Specialized S-works E5 road, GT Talera
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Take that big white reflector out of the spokes.
Seriously though,
Assuming you have the bike upside down, and when you spin the wheel the bike bounces a bit?
Its probably the extra weight of the valve stem and cap, since there is no counter weight across from it, accept maybe some stickers. If you pull the tube out then the other side of the rim will be slightly heavier since there is no hole in that side.
You can remove the cap or add a counter weight and see if that helps, but frankly I don't think that little of an off balance wheel is going to make any difference.
Seriously though,
Assuming you have the bike upside down, and when you spin the wheel the bike bounces a bit?
Its probably the extra weight of the valve stem and cap, since there is no counter weight across from it, accept maybe some stickers. If you pull the tube out then the other side of the rim will be slightly heavier since there is no hole in that side.
You can remove the cap or add a counter weight and see if that helps, but frankly I don't think that little of an off balance wheel is going to make any difference.
#6
Senior Member
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225
Bikes: Catrike 559 I own some others but they don't get ridden very much.
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 643 Times
in
364 Posts
Originally Posted by Smoothie104
Its probably the extra weight of the valve stem and cap, since there is no counter weight across from it, accept maybe some stickers. If you pull the tube out then the other side of the rim will be slightly heavier since there is no hole in that side.
#7
newbie newbie
Join Date: Mar 2003
Location: Happy to be in FLORIDA
Posts: 633
Bikes: Titanium Indy Fab 29" mtb
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
You know this almost sounds as if he has the tube pinched between the tire and the wheel bead. Try remounting the tire and see if that helps. If it is pinched you are headed for a flat.
#8
Senior Member
Join Date: Dec 2003
Location: Huntsville, AL
Posts: 157
Bikes: Sano, Raleigh
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by Retro Grouch
Actually, the rim opposite the valve stem is usually the heaviest point. Rim manufacturers use steel pins to pin the extrusion at the joint which is usually exactly opposite the valve hole. It's easy to tell on a front wheel just hold it off the ground and see where the wheel stops spinning. I usually put computer magnets on a spoke near the valve stem to minimize the imbalance.
I used about 4 inches of lead plumbers solder, wrapped around a spoke on both wheels, to bring them into balance. Not sure if that's recommended by anyone.
#9
Senior Member
Join Date: Nov 2003
Location: Home of the Homeless
Posts: 610
Bikes: Rustbuckets, the lot of them.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Does it make the bike move up and down while you're riding it? If yes, you have a serious problem. If no, then ignore it.