can't figure out where this headset spacer goes
09-26-08, 12:31 PM
#1
Full Member
Thread Starter
can't figure out where this headset spacer goes
just regreased the bearings in my headset but I've got a small spacer leftover and I can't figure out where it goes. No, I didn't pay attention when I took the thing apart a few months ago!!! the spacer doesn't seem to fit anywhere, it's too tight to fit under the locknut. The headset seems to be working on, no play, and moves freely. Is it a big deal if I leave the spacer off?
09-26-08, 12:48 PM
#2
Senior Member
Picture?
Some headsets have a plastic seal on top of the locknut to prevent water from dripping down the stem and corroding onto the steerer.
Some headsets have a plastic seal on top of the locknut to prevent water from dripping down the stem and corroding onto the steerer.
09-26-08, 05:02 PM
#4
Senior Member
Join Date: Sep 2008
Location: yreka, ca
Posts: 542
Bikes: like 15. my favorite a 1951 schwinn spitfire cruiser. also have a 1959 amf roadmaster, 1962 jch deluxe cruiser among others.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
did it go at the bottom of the fork? pictures would help a lot. sorry couldnt be more help.
09-26-08, 08:39 PM
#6
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
Is it a spacer or just a seal ring? Many headsets have a rubber or plastic seal between the bearing cups and the crown race or top cover.
09-27-08, 06:18 AM
#8
Senior Member
Join Date: Dec 2005
Location: Boulder, Colorado
Posts: 1,383
Bikes: Cinelli Supercoursa 69, Ritchey Breakaway Cross, Mondonico Diamond Extra 05, Coors Light Greg Lemond (built by Scapin) 88, Scapin MTB, Stumpjumper 83, Specialized Stumpjumper M4, Lemond Poprad 2001
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Liked 2 Times
in
1 Post
Spacers are only needed if the Threaded portion of the fork is long enough to require spacers to prevent the lock nut from bottoming out on the top of the steerer tube before locking the head set in position. There is a washer between the threaded cup and the locknut that makes it easier to lock down the 2 threaded parts with significant torque without causing damage to the 2 nuts. It us usually of a softer material and it may be keyed by a tooth or a flatted surface and is usually very tight on the steerer tube. It helps to prevent the nuts from loosening. It is important.
09-28-08, 06:56 AM
#10
Full Member
Thread Starter
There is a washer between the threaded cup and the locknut that makes it easier to lock down the 2 threaded parts with significant torque without causing damage to the 2 nuts. It us usually of a softer material and it may be keyed by a tooth or a flatted surface and is usually very tight on the steerer tube. It helps to prevent the nuts from loosening. It is important.
