152mm Triple Crankset - source needed
#1
Senior Member
Thread Starter
Join Date: Nov 2007
Posts: 237
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times
in
1 Post
152mm Triple Crankset - source needed
Looking to find a 152mm triple for my son's 24" mountain bike. It has a double now and he is riding harder.
I know SR Suntour makes one, because it is used on the Specialized Hotrock. But I can't seem to find a place that sells it. His current bike has a square taper BB. Anyone know a source
I know SR Suntour makes one, because it is used on the Specialized Hotrock. But I can't seem to find a place that sells it. His current bike has a square taper BB. Anyone know a source
#5
Senior Member
Thread Starter
Join Date: Nov 2007
Posts: 237
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times
in
1 Post
I went to a local used bike place and found a triple from an old Trek. Turns out that Suntour makes one, but it is only available in Europe! Go figure. Now a new Bottom Bracket...
#6
Senior Member
Join Date: Apr 2009
Location: Fresno, CA.
Posts: 227
Bikes: Mongoose XR-75
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#7
Senior Member
Join Date: Aug 2005
Location: Minneapolis, MN
Posts: 798
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 16 Post(s)
Likes: 0
Liked 24 Times
in
11 Posts
Do you know if they will work on a bike other than MTB? I am looking into shortened cranks because I cannot bend my right knee more than 60 degrees, and currently have to do all my pedaling with my left leg. If I could get the cranks short enough I might be able to pedal a full 360 degrees with my right leg.
The smaller rings are rarely a problem because you can really spin shorties when you need to.
If both legs are the same length, you need the same length cranks. Several people have asked for a specific length recommended by an Orthopedic Dr. or a Physical Therapist.
Another method is to use boards to add height to a step, to see how much higher you can place your limited foot above your good one, without tilting your pelvis. 1/2 this distance is crank length.
#8
Senior Member
Join Date: Apr 2009
Location: Fresno, CA.
Posts: 227
Bikes: Mongoose XR-75
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Very few of those shortened IsoFlows end up on mountain bikes. Most go on recumbents, but quite a few go to riders of non-'bents with range of motion issues. I recently sold a 95mm set to a guy who is fit, but has very restricted motion in one knee. Despite this he is able to be competitive in Brevets.
The smaller rings are rarely a problem because you can really spin shorties when you need to.
If both legs are the same length, you need the same length cranks. Several people have asked for a specific length recommended by an Orthopedic Dr. or a Physical Therapist.
Another method is to use boards to add height to a step, to see how much higher you can place your limited foot above your good one, without tilting your pelvis. 1/2 this distance is crank length.
The smaller rings are rarely a problem because you can really spin shorties when you need to.
If both legs are the same length, you need the same length cranks. Several people have asked for a specific length recommended by an Orthopedic Dr. or a Physical Therapist.
Another method is to use boards to add height to a step, to see how much higher you can place your limited foot above your good one, without tilting your pelvis. 1/2 this distance is crank length.
#9
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,778
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3583 Post(s)
Liked 3,395 Times
in
1,929 Posts
TA still makes cranks down to 155mm, if that would work for you.