cannondale with durac-ace bottom bracket?
#1
Junior Member
Thread Starter
Join Date: Mar 2006
Posts: 12
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
cannondale with durac-ace bottom bracket?
OK guys, forgive my ignorance! Recently got a system six cannondale road bike (used). It has dura-ace cranks. Does that mean it also has a dura-ace BB? Or could it be the cannondale SI or BB30? It has the new "exo" style and around the edge is labeled BC1.37x24? Is this dura-ace? Also, I haven't overhauled a new one like this. Any web-site with good info would be appreciated. I assume it's some type of sealed cartridge bearing. Any special tools needed? Thanks in advance for info.
#2
cab horn
Join Date: Jun 2004
Location: Toronto
Posts: 28,353
Bikes: 1987 Bianchi Campione
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 42 Post(s)
Likes: 0
Liked 25 Times
in
18 Posts
If it doesn't have an adapter to take it down to regular english (1.37x24) then it's mos def not BB30. BG30 for the ****ing win. I'm going to asume some sort of shimano cart bb, or more likely 16 nocth ect bb tht takes 16 thingy bb.
Give us a picture.
Give us a picture.
#3
Senior Member
Join Date: Jul 2007
Location: San Jose, Ca
Posts: 1,213
Bikes: 09 Specialized Tricross Sport
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
If it looks anything like this..
It should be a shimano bb cup.
I coulda sworn my 105 bb cup had "5600" written on it. If I'm right, a dura ace cup will have "7800" written on it.
The cdale system six bb should look like this:
It should be a shimano bb cup.
I coulda sworn my 105 bb cup had "5600" written on it. If I'm right, a dura ace cup will have "7800" written on it.
The cdale system six bb should look like this:
#4
Junior Member
Thread Starter
Join Date: Mar 2006
Posts: 12
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Yup, it's dura-ace. Thanks.
I went to the shimano site and saw the expanded view along with tools needed, and torque specs.
I remember with the older style brackets, you had to really get the fixed cup tight in the frame. I don't know if this was a problem with my specific frame, etc. Is there anything special about installing these "adapters" as they are called, other than following the torque specs?
I went to the shimano site and saw the expanded view along with tools needed, and torque specs.
I remember with the older style brackets, you had to really get the fixed cup tight in the frame. I don't know if this was a problem with my specific frame, etc. Is there anything special about installing these "adapters" as they are called, other than following the torque specs?
#5
Senior Member
Join Date: Jul 2007
Location: San Jose, Ca
Posts: 1,213
Bikes: 09 Specialized Tricross Sport
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Thus, I installed it again, this time not tightening just one side but instead, tightening each cup about 50 in lb at at time, alternatingly, until each one had reached shimano's torque spec. This has left the bb completely noise free, no matter how hard I sprint or climb out of saddle.
So at least in my experience, it has to be done a particular way.