Lacing a 32h hub to a 36h rim
#1
Junior Member
Thread Starter
Join Date: May 2008
Posts: 23
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Lacing a 32h hub to a 36h rim
Is this possible? I thought it was by skipping two spoke holes on the rim. You would have to lace the top half and bottom halves of the wheel separately. Any ideas?
-- Boris
-- Boris
#2
Senior Member
Join Date: Jun 2007
Location: A Coffin Called Earth. or Toronto, ON
Posts: 12,257
Bikes: Bianchi, Miyata, Dahon, Rossin
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 5 Times
in
5 Posts
https://www.sheldonbrown.com/rinard/
the fun part is calculating the spoke length required for that.
the fun part is calculating the spoke length required for that.
__________________
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
#5
Luddite
Join Date: Jan 2007
Location: Portland, OR
Posts: 276
Bikes: Univega Gran Turismo, Cannondale Synapse, Bianchi Aquiletta Folder
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I wouldn't recommend it- assuming the rim isn't offset-drilled, you would still need to skip a hole every 8,which would leave 4 spots on the rim with no spoke. It would be murder to get it straight and tensioned and the spots with no spoke would be weaker. Better to lace a 32 hole rim to a 36 hole hub- then it's just a matter of getting the spoke lengths right. I once laced a 40 hole hub to a 36 hole rim- I needed 9 different spoke lengths (no dish on the wheel- otherwise it would have been 18 lengths). An interesting geometry problem.
#6
Senior Member
Join Date: Mar 2008
Posts: 8,688
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 295 Times
in
222 Posts
Possible, but inadvisable. I'm no stranger to experimenting, but I wouldn't try that unless:
- I was desperate for something to do
- I couldn't get any other parts
- I really needed a wheel
- That rim is also available in 20-24 H drilling, to have some indication that it'd survive the increased span between spokes
- That the rim isn't drilled with a serious offset angle between spokes
You "can't" skip two holes consecutively, you'd want them spaced out. but that means that half the wheel will be built with the spokes in lateral cross. Doable, but only if there isn't much offset in the drilling.
- The other way around is much safer, if a bit tedious to build
- Ride with extreme care and attention to changes
- Don't expect too much
- Assume full responsibility for your mismatched build
If I was desperate to use those bits I'd make myself a pair of adapter flanges. Basically two big washers, with two rows of holes. The holes closest to the inside edge would let the washer be screwed onto the the 16H hub flange while the outside row would hold 18 holes to match the rim. Might require some extra tweaking if it's on the DS of an externally geared hub.
- I was desperate for something to do
- I couldn't get any other parts
- I really needed a wheel
- That rim is also available in 20-24 H drilling, to have some indication that it'd survive the increased span between spokes
- That the rim isn't drilled with a serious offset angle between spokes
You "can't" skip two holes consecutively, you'd want them spaced out. but that means that half the wheel will be built with the spokes in lateral cross. Doable, but only if there isn't much offset in the drilling.
- The other way around is much safer, if a bit tedious to build
- Ride with extreme care and attention to changes
- Don't expect too much
- Assume full responsibility for your mismatched build
If I was desperate to use those bits I'd make myself a pair of adapter flanges. Basically two big washers, with two rows of holes. The holes closest to the inside edge would let the washer be screwed onto the the 16H hub flange while the outside row would hold 18 holes to match the rim. Might require some extra tweaking if it's on the DS of an externally geared hub.
#7
Senior Member
Join Date: May 2005
Location: SFBay
Posts: 2,334
Bikes: n, I would like n+1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 127 Post(s)
Likes: 0
Liked 133 Times
in
108 Posts
First of all, you don't need 8 spoke lengths. I've done this with a Shimano high flange mtb disc hub and a 20" DX32 rim (temporary for a recumbent project if you were wondering), and I used the spoke length which was correct for 36 hole. However, you're going to have to do the hub in 4 groups, not 2 to avoid a huge gap in the rim. As a result, half of your spokes will enter eyelets on the wrong side of the rim. Also, it's going to look really bad and people are probably going to write you off as not being is the sharper half of the tools, no matter how good you are on a bike.
So, in conclusion, and having actually done this myself, does it work, yes. Should you do it, no.
So, in conclusion, and having actually done this myself, does it work, yes. Should you do it, no.