Dishing wheel
#1
30mi/day commuter
Thread Starter
Join Date: Apr 2008
Location: Toronto, Canada
Posts: 797
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 5 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Dishing wheel
when you dish your rear wheel to make the rim sit evenly within your dropouts do you actually get it to sit evenly or do you just get it close?
Do you tighten the opposing spokes much?
Do you tighten the opposing spokes much?
#2
Bill
Join Date: May 2007
Location: HIGHLANDS RANCH, CO
Posts: 630
Bikes: Specialized Globe Sport, Specialized Stumpjumper FSR Pro
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Everything has its acceptible tolerance. Barnett uses a value of 2mm. In other words if the rim is offset less then 2mm from the perfect center it is acceptible. I'm sure one could set the dish more precisely but why? What is the benefit? There is a cost to any level of precision either in dollars or time.
#3
Senior Member
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225
Bikes: Catrike 559 I own some others but they don't get ridden very much.
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 643 Times
in
364 Posts
I get it pretty close. I wouldn't be happy with a wheel dish that was 2 mm off. I'm thinking that 1 mm is a little more like it.
I think that it's best to sneak up on fine adjustments like final wheel dishing. Assuming the wheel is true and round to begin with, I tighten all of the spokes on the side I want to pull the rim over to by 1/4 turn and loosen all of the spokes on the other side an equal amount. If you adjust every spoke an equal amount, it won't affect the trueness or roundness of the wheel.
I think that it's best to sneak up on fine adjustments like final wheel dishing. Assuming the wheel is true and round to begin with, I tighten all of the spokes on the side I want to pull the rim over to by 1/4 turn and loosen all of the spokes on the other side an equal amount. If you adjust every spoke an equal amount, it won't affect the trueness or roundness of the wheel.
#4
Senior Member
Join Date: Feb 2005
Location: Oklahoma
Posts: 9,438
Bikes: Trek 5500, Colnago C-50
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 7 Times
in
6 Posts
0.5 mm
Rear wheel dishing and final lateral truing should be done with the tire and tube fully inflated. The asymmetrical spoke tension causes the rim to move laterally with the change in air pressure.
Al
Rear wheel dishing and final lateral truing should be done with the tire and tube fully inflated. The asymmetrical spoke tension causes the rim to move laterally with the change in air pressure.
Al
Last edited by Al1943; 06-19-09 at 04:12 PM.
#5
Slow mechanic
Join Date: Jun 2007
Location: Calgary
Posts: 237
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I say 1mm but I don't have any claim to authority.
I wonder if Barnett is saying 2mm or a calls for a maximum 2mm gap shown by a dishing tool.
I wonder if Barnett is saying 2mm or a calls for a maximum 2mm gap shown by a dishing tool.
#6
Senior Member
Join Date: Jun 2007
Location: A Coffin Called Earth. or Toronto, ON
Posts: 12,257
Bikes: Bianchi, Miyata, Dahon, Rossin
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 5 Times
in
5 Posts
within 1mm each way off of center.
did you respace your hub or what?
did you respace your hub or what?
__________________
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
#7
30mi/day commuter
Thread Starter
Join Date: Apr 2008
Location: Toronto, Canada
Posts: 797
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 5 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
"did you respace your hub or what?"
actually my chain was popping off my cassette for 1 ride home when i shifted to my lowest gear. It happened 3 times on my way home and each time it popped off it would get stuck between my cassette and hub and i would grind (literally) to a stop. All the outside spokes on the cassette side were broken or about to break to I had to replace them all.
actually my chain was popping off my cassette for 1 ride home when i shifted to my lowest gear. It happened 3 times on my way home and each time it popped off it would get stuck between my cassette and hub and i would grind (literally) to a stop. All the outside spokes on the cassette side were broken or about to break to I had to replace them all.
#8
I have senior moments...
Join Date: Oct 2008
Location: Woodside, CA
Posts: 2,151
Bikes: Many
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
"did you respace your hub or what?"
actually my chain was popping off my cassette for 1 ride home when i shifted to my lowest gear. It happened 3 times on my way home and each time it popped off it would get stuck between my cassette and hub and i would grind (literally) to a stop. All the outside spokes on the cassette side were broken or about to break to I had to replace them all.
actually my chain was popping off my cassette for 1 ride home when i shifted to my lowest gear. It happened 3 times on my way home and each time it popped off it would get stuck between my cassette and hub and i would grind (literally) to a stop. All the outside spokes on the cassette side were broken or about to break to I had to replace them all.
#9
hello
#11
Senior Member
Join Date: Aug 2008
Location: Tucson, Arizona
Posts: 704
Bikes: '02 Lemond Buenos Aires, '98 Fuji Touring w/ Shimano Nexus premium, '06 Jamis Nova 853 cross frame set up as commuter, '03 Fuji Roubaix Pro 853 back up training bike
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
I'm building my first rear wheel now. I established the proper dish early on, after taking up the slack and initial truing. I'll finish the wheel, note the dish position according to the Park stand's calipers, then install the tube, tire, inflate, and see if or where things move.