Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Shimano 105 Brifter repair

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Shimano 105 Brifter repair

Old 07-23-09, 12:42 PM
  #1  
Senior Member
Thread Starter
 
Join Date: Mar 2005
Posts: 1,442
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Shimano 105 Brifter repair

I picked up Giant roadster from about 1994; one of those carbon-fiber/alluminum jobs. Pretty decent shape, but the left brifter is wonky.
I shot it full of WD-40 and restored some clicking, but it's not "catching" on the upshifts yet.
Are these critters serviceable, or should I forget it and start haunting eBay for a new one?
Bikewer is offline  
Old 07-23-09, 12:56 PM
  #2  
Senior Member
 
Join Date: Apr 2006
Posts: 3,653
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 380 Post(s)
Likes: 0
Liked 106 Times in 80 Posts
They are not serviceable so you buy a new one. Roger
rhenning is offline  
Old 07-23-09, 03:34 PM
  #3  
Senior Member
Thread Starter
 
Join Date: Mar 2005
Posts: 1,442
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Or use more WD-40.....Cures cancer, I hear.
Bikewer is offline  
Old 07-23-09, 04:14 PM
  #4  
Acetone Man
 
Join Date: Oct 2004
Location: PDX
Posts: 251
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
First generation STI's are readily serviceable. Remove the lever from the hood by unscrewing the set-screw holding the pivot in place, then drive the pivot out with a screwdriver. A round nut with four evenly spaced slots holds the shifter together from the backside of the lever. Remove this nut by using sharp needlenosed pliers clamped in a vise to engage two of the slots. Remove the dust cover, the return spring for the return paddle, and the return paddle shifter. Once you've done that, put a spacer of some sort back over the central post which is thick enough to take up all the slack before the threads at the top, then thread the round nut back on fingertight to the spacer. From the front, remove the faceplate with a 5mm allen key and the lever return spring will pop out along with a spacer. Thread the 5mm bolt back into its hole because a bushing may fall out later if you don't. On the backside again, remove the phillips head screw. Because you've threaded the round nut back on with the spacer, the shifter core will come out in one intact piece after you remove this screw. Loosen the round nut a little bit to put some play into the shifter internals and dunk it in some paint thinner. Use an old toothbrush to thoroughly clean the mechanism of any grease, thoroughly rinse with a high pressure hose attachment and aftersoak, and thoroughly dry. Drip some triflow into the deepest parts of the mechanism, wipe the surface clean, then brush fresh grease everywhere you can get with a small paintbrush. That's the quick and dirty way, at any rate. It really isn't all that difficult to completely take apart the shifter and reassemble, in which case you would use grease everywhere and no triflow. But that'll take at least an extra 1/2 hour. Line up each part that comes off the central post in the order in which it was removed as it will immensely help the return assembly. Clean and grease all the other parts then reassemble by reversing the disassembly. To get the lever return spring back in place engage the spring in both its holes, with the shifter cap at a 90 degree angle to its destination, then rotate it back into place. The paddle return spring is easy if you have a triple and horrible horrible horrible if you have a double. Either way, a small flathead screwdriver is the way to go. Use loctite on the round nut and the pivot set screw; you don't want this puppy coming loose on you in the middle of a ride.

Last edited by Thasiet; 07-23-09 at 04:28 PM.
Thasiet is offline  
Old 07-23-09, 04:16 PM
  #5  
Genius
 
FlatMaster's Avatar
 
Join Date: Jan 2008
Location: Auburn, AL
Posts: 324

Bikes: Specilized Sirrus

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I've taken one apart once, but it was a pain. I had a cable snap off within the brifter. I was able to get everything back together except the spring that holds the brake lever straight down, so the lever had a little bit of swing until it hit the spring that actually controlled the shifting. If you're mechanically savvy, go for it.
FlatMaster is offline  
Old 07-23-09, 05:58 PM
  #6  
Senior Member
Thread Starter
 
Join Date: Mar 2005
Posts: 1,442
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time in 1 Post
I'll play with it a bit more; I found that the cable was badly frayed and tended to catch in the frame guide, and the front DR was also extremely cruddy.
This is a 1994 bike that has likely been sitting for some years. By the look of the critter, it was not well-maintained.
Still, it's bike that retailed for about 1400.00, and I got it for nothing...
Bikewer is offline  
Old 07-23-09, 09:38 PM
  #7  
Junior Member
 
Join Date: Jul 2009
Posts: 17
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I had a 105 right brifter go bad. WD-40 didn't help. I'm cruising e-Bay now. I'm currently watching a pair of Ultegra units that are reasonable $$ so far.
vortexrob is offline  
Old 07-24-09, 12:23 PM
  #8  
Senior Member
 
Join Date: Sep 2006
Location: Layton, UT
Posts: 686

Bikes: 2004 Giant OCR, 2002 Specialized Stumpjumper, 2008 Trek 6500 Disc

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I tried to no avail to repair one. I opted for the ebay route.
gholt is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.