Handlebar tape - Old style brake levers
#1
Senior Member
Thread Starter
Join Date: Jan 2009
Posts: 99
Bikes: 2014 Trek 7.4 FX Hybrid - Early 80s Raleigh Rapide 10 Speed
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Handlebar tape - Old style brake levers
I've watched a few on-line videos on how to wrap handlebars but none of them I've found cover how to do it with the old style handlebars that have the secondary brake lever attached on the same pivot point as the main brake lever. (see attached photo...sorry it isn't very good....click on thumbnail to enlarge)
I bought some inexpensive foam bar tape and if I wrap it behind and around the brake lever mount, the secondary brake will rub the foam. Should I just wrap around the brake mount and then cut away part of the tape to make room for the other brake lever to pivot? I'm fearful of doing that because I think the tape might tear in that place or even break.
If I don't wrap around the back of the brake lever mount, it will leave an unsightly gap on the outside even if I use the 3" strips. It also wouldn't reverse directions on the tape at that point which goes against standard procedures from what I understand.
Also, I really can't use the 3" pieces that come with the kit that are to wrap aroudn the bottom of the break lever mount. There isn't enough room on the inside of the brake mount. I could use it on the outside and then stop just after the bottom. The bike doesn't have hoods either so I'm not sure what these pieces would look like anyway without a hood to cover up the ends.
The tape that was on the bike was original (early eighties) and was about as thick as electrical tape. I'm sure this has been encountered before with those wanting to put some thicker tape on the old style handlbars. Any suggestions would be appreciated.
Thanks
I bought some inexpensive foam bar tape and if I wrap it behind and around the brake lever mount, the secondary brake will rub the foam. Should I just wrap around the brake mount and then cut away part of the tape to make room for the other brake lever to pivot? I'm fearful of doing that because I think the tape might tear in that place or even break.
If I don't wrap around the back of the brake lever mount, it will leave an unsightly gap on the outside even if I use the 3" strips. It also wouldn't reverse directions on the tape at that point which goes against standard procedures from what I understand.
Also, I really can't use the 3" pieces that come with the kit that are to wrap aroudn the bottom of the break lever mount. There isn't enough room on the inside of the brake mount. I could use it on the outside and then stop just after the bottom. The bike doesn't have hoods either so I'm not sure what these pieces would look like anyway without a hood to cover up the ends.
The tape that was on the bike was original (early eighties) and was about as thick as electrical tape. I'm sure this has been encountered before with those wanting to put some thicker tape on the old style handlbars. Any suggestions would be appreciated.
Thanks
#2
Senior Member
Join Date: Jun 2007
Location: A Coffin Called Earth. or Toronto, ON
Posts: 12,257
Bikes: Bianchi, Miyata, Dahon, Rossin
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 5 Times
in
5 Posts
use a thinner bar tape, like cloth.
or use 4 pieces of rubber grips.
or use 4 pieces of rubber grips.
__________________
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
#3
You gonna eat that?
Those foam rubber grips get nasty. Just wrap it like normal, use the little piece on the outside only (and parallel to the bar, not around it), and try to leave as much room as possible around the suicide lever. I've managed to do it successfully.
#4
STFD
Join Date: Jul 2008
Location: North Bergen, NJ
Posts: 778
Bikes: '80 Windsor Carrera Sport, '02 Specialized Sirrus A1, '10 Giant Escape 2
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
If you want to keep the auxiliary levers (all us kool kids just took them off back in the day), you'll have to either use cloth bar tape, or so something kloojy.
If your goal is to do a vintage restoration of the bike, use cloth tape.
If your goal is to make the bike comfortable, either take the aux levers off, or spend $20-30 on some new levers, like basic Tektro ones, and wrap with the padded tape you have.
A klooj could be worked up, using some combination of padded tape, old fashioned cloth tape, and/or maybe something like gel padding. One way that comes to mind might be to wrap with padded tape from the stem to the point where the padded tape would start interfering with the aux lever. Then cut it and tape it down, and cut 2 or 3 or 4 3"-5" strips of the padded tape. From the point where you stopped wraping the padded tape, start wrapping with thin cloth tape, wraping over the strips of padded tape, which you're orienting parallel to the bar. When you get just past the brake lever clamp, cut and tape down the cloth tape, and start wrapping again with padded tape.
OK, that would be a pain to do, and might look ugly. I guess I'd attempt it, just to prove it could be done. Prove to whom? No one, I guess.
Yeah, I'd just take those aux levers right off and wrap with padded tape, I would.
If your goal is to do a vintage restoration of the bike, use cloth tape.
If your goal is to make the bike comfortable, either take the aux levers off, or spend $20-30 on some new levers, like basic Tektro ones, and wrap with the padded tape you have.
A klooj could be worked up, using some combination of padded tape, old fashioned cloth tape, and/or maybe something like gel padding. One way that comes to mind might be to wrap with padded tape from the stem to the point where the padded tape would start interfering with the aux lever. Then cut it and tape it down, and cut 2 or 3 or 4 3"-5" strips of the padded tape. From the point where you stopped wraping the padded tape, start wrapping with thin cloth tape, wraping over the strips of padded tape, which you're orienting parallel to the bar. When you get just past the brake lever clamp, cut and tape down the cloth tape, and start wrapping again with padded tape.
OK, that would be a pain to do, and might look ugly. I guess I'd attempt it, just to prove it could be done. Prove to whom? No one, I guess.
Yeah, I'd just take those aux levers right off and wrap with padded tape, I would.
#5
Great State of Varmint
Join Date: Sep 2008
Location: Dante's Third Ring
Posts: 7,476
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 15 Times
in
15 Posts
You can take a 6-inch or so rectangle of the tape (if it's cloth and has stick-um on one side) and place it on one side of the brake-fastener - around the bar - and onto the other side of the brake-fastener. Then wrap the bars. I wrap from stem - to - bottom. It doesn't come loose if you give it 2 1/2 wraps to start while pulling tight. Looks better than a encirclement of electrical-tape. And it's the way my friends & colleagues have always done this.
We always removed the 'suicide-levers' as they promote confidence in grabbing those things in a panic stop, and ending up on the hood of a car. Or worse.
We always removed the 'suicide-levers' as they promote confidence in grabbing those things in a panic stop, and ending up on the hood of a car. Or worse.
#6
Senior Member
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225
Bikes: Catrike 559 I own some others but they don't get ridden very much.
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 643 Times
in
364 Posts
"Tressostar" cotton tape is the period appropriate handlebar wrap. It'll leave you enough room for your levers to operate. Each roll is only long enough to do one side so you have to buy two. I find it faster and easier to remove the "suicide levers" and replace them after I'm done wrapping the bars.
#7
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
One comment; have you been wondering why many of the above posters have refered to the auxiliary levers as "suicide levers"? There is a reason.
#8
Senior Member
Join Date: Jun 2007
Location: A Coffin Called Earth. or Toronto, ON
Posts: 12,257
Bikes: Bianchi, Miyata, Dahon, Rossin
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 5 Times
in
5 Posts
speed adjusters is what I would call them.
if you combine them with modern calipers or cantis, they will work pretty decently if the pads are set really close to the rim.
if you combine them with modern calipers or cantis, they will work pretty decently if the pads are set really close to the rim.
__________________
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
#9
Senior Member
Thread Starter
Join Date: Jan 2009
Posts: 99
Bikes: 2014 Trek 7.4 FX Hybrid - Early 80s Raleigh Rapide 10 Speed
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
If you want to keep the auxiliary levers (all us kool kids just took them off back in the day), you'll have to either use cloth bar tape, or so something kloojy.
If your goal is to do a vintage restoration of the bike, use cloth tape.
If your goal is to make the bike comfortable, either take the aux levers off, or spend $20-30 on some new levers, like basic Tektro ones, and wrap with the padded tape you have.
If your goal is to make the bike comfortable, either take the aux levers off, or spend $20-30 on some new levers, like basic Tektro ones, and wrap with the padded tape you have.
One comment; have you been wondering why many of the above posters have refered to the auxiliary levers as "suicide levers"? There is a reason.
"Tressostar" cotton tape is the period appropriate handlebar wrap. It'll leave you enough room for your levers to operate. Each roll is only long enough to do one side so you have to buy two. I find it faster and easier to remove the "suicide levers" and replace them after I'm done wrapping the bars.
kloojy
I just had a thought....... What if I wrapped the bars with the foam tape and skipped going around the brake lever mount and just kept wrapping. Then If I came back with the cloth tape over it it would cover the uglyness caused by skipping around the brake lever mount. I've have comfort and cosmetics. Do you think it would be too thick? Would it even work?
Thanks everyone for your advice.
#10
Senior Member
Join Date: Sep 2007
Location: Vancouver
Posts: 1,437
Bikes: NOYB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
With brake levers like those, I just wrap up to the bottom of the lever bodies, cross over on the clamps, and continue wrapping above.
Since there's no hoods, and making sure there is clearance for the suicide levers is very important, there's no point in using an extra piece of tape or wrapping around the lever body to cover gaps or whatever.
Since there's no hoods, and making sure there is clearance for the suicide levers is very important, there's no point in using an extra piece of tape or wrapping around the lever body to cover gaps or whatever.
#11
Senior Member
Join Date: May 2005
Location: Queanbeyan, Australia.
Posts: 4,135
Mentioned: 85 Post(s)
Tagged: 0 Thread(s)
Quoted: 3450 Post(s)
Liked 420 Times
in
289 Posts
I had a look at your picture and thought to myself, where are your brake hoods?
Then I remembered that those levers with the suicide levers didn't come with hoods and to be honest that changes everything. All the instructions you have read so far on bar wrapping are assuming that you have rubber hoods and NO suicide levers.
Back in the day when those levers were common cheap bikes just used a thin plastic bar wrap and expensive bikes used cloth tape which wasn't much thicker. To do a really neat wrap job with those bars and levers I would make sure the levers were positioned where I wanted them, tape the underside of the lever body clamp in place, take the lever body off, wrap the bars and when you get to the lever clamp wrap as closely as you can without interfering with the bolt hole but definitely covering the underside of the clamp and then bolting the lever body back on.
Thats the best you will do with those levers. The technique of wrapping around the lever body with it bolted in place is assuming that you will cover them with rubber hoods.
EDIT: Ohh, and I forgot to mention. Modern cork tape may not be the best to use with such levers. It just wasn't part of their design considerations. Cloth tape would give the neatest result. You may be able to bolt the lever bodies back down onto cork tape although its possible that the bolt won't reach. You will just have to see.
Anthony
Then I remembered that those levers with the suicide levers didn't come with hoods and to be honest that changes everything. All the instructions you have read so far on bar wrapping are assuming that you have rubber hoods and NO suicide levers.
Back in the day when those levers were common cheap bikes just used a thin plastic bar wrap and expensive bikes used cloth tape which wasn't much thicker. To do a really neat wrap job with those bars and levers I would make sure the levers were positioned where I wanted them, tape the underside of the lever body clamp in place, take the lever body off, wrap the bars and when you get to the lever clamp wrap as closely as you can without interfering with the bolt hole but definitely covering the underside of the clamp and then bolting the lever body back on.
Thats the best you will do with those levers. The technique of wrapping around the lever body with it bolted in place is assuming that you will cover them with rubber hoods.
EDIT: Ohh, and I forgot to mention. Modern cork tape may not be the best to use with such levers. It just wasn't part of their design considerations. Cloth tape would give the neatest result. You may be able to bolt the lever bodies back down onto cork tape although its possible that the bolt won't reach. You will just have to see.
Anthony
Last edited by AnthonyG; 02-17-09 at 08:10 AM.
#12
Senior Member
Thread Starter
Join Date: Jan 2009
Posts: 99
Bikes: 2014 Trek 7.4 FX Hybrid - Early 80s Raleigh Rapide 10 Speed
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
To do a really neat wrap job with those bars and levers I would make sure the levers were positioned where I wanted them, tape the underside of the lever body clamp in place, take the lever body off, wrap the bars and when you get to the lever clamp wrap as closely as you can without interfering with the bolt hole but definitely covering the underside of the clamp and then bolting the lever body back on.
EDIT: Ohh, and I forgot to mention. Modern cork tape may not be the best to use with such levers. It just wasn't part of their design considerations. Cloth tape would give the neatest result. You may be able to bolt the lever bodies back down onto cork tape although its possible that the bolt won't reach. You will just have to see.
EDIT: Ohh, and I forgot to mention. Modern cork tape may not be the best to use with such levers. It just wasn't part of their design considerations. Cloth tape would give the neatest result. You may be able to bolt the lever bodies back down onto cork tape although its possible that the bolt won't reach. You will just have to see.
1. You say to leave the clamp on and wrap the underside of it without interfering with the bolt hole. The bolt hole is on top of the clamp. Are we talking about different types of clamps or am I just not understanding? (The clamp is a c shape with a nut connecting the two sides which is where the bolt connects just under where the brake lever mounts. If I understand you correctly, I would wrap close to the clamp, then on the under side of it and then continue on. The bolt couldn't interfer. ??
2. Assuming I wrap using your suggestion above instead of the methods described previously, I won't reverse directions at the brake lever which will mean the top of the bar is wrapped in reverse of the usual method. How likely is this to cause the tape to become lose?
3. If I clamp the brake lever down, it will be on top of the foam tape (assuming I use the foam tape I have instead of finding the cloth tape.) I am fearful the brake clamp might cut into the foam causing early failure.
4. You say to tape the clamp in place before starting. Are you meaning to tape it in place with the bar tape or some electrical tape?
Thanks
#13
Junior Member
Join Date: Sep 2006
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
i have a 74 le tour w those "suicide levers". i left the levers on and had no problem wrapping my bars. i like to be able to change hand positions from time to time. i converted it to a single speed. feel very safe when i ride. never got the flying over the handlebar feeling. i ride my bike in the country and the city in all conditions.
#14
Senior Member
Join Date: May 2005
Location: Queanbeyan, Australia.
Posts: 4,135
Mentioned: 85 Post(s)
Tagged: 0 Thread(s)
Quoted: 3450 Post(s)
Liked 420 Times
in
289 Posts
I hadn't thought of removing the brake levers before wrapping. Sounds like a good idea. I have a couple of concerns though.
1. You say to leave the clamp on and wrap the underside of it without interfering with the bolt hole. The bolt hole is on top of the clamp. Are we talking about different types of clamps or am I just not understanding? (The clamp is a c shape with a nut connecting the two sides which is where the bolt connects just under where the brake lever mounts. If I understand you correctly, I would wrap close to the clamp, then on the under side of it and then continue on. The bolt couldn't interfer. ??
2. Assuming I wrap using your suggestion above instead of the methods described previously, I won't reverse directions at the brake lever which will mean the top of the bar is wrapped in reverse of the usual method. How likely is this to cause the tape to become lose?
3. If I clamp the brake lever down, it will be on top of the foam tape (assuming I use the foam tape I have instead of finding the cloth tape.) I am fearful the brake clamp might cut into the foam causing early failure.
4. You say to tape the clamp in place before starting. Are you meaning to tape it in place with the bar tape or some electrical tape?
Thanks
1. You say to leave the clamp on and wrap the underside of it without interfering with the bolt hole. The bolt hole is on top of the clamp. Are we talking about different types of clamps or am I just not understanding? (The clamp is a c shape with a nut connecting the two sides which is where the bolt connects just under where the brake lever mounts. If I understand you correctly, I would wrap close to the clamp, then on the under side of it and then continue on. The bolt couldn't interfer. ??
2. Assuming I wrap using your suggestion above instead of the methods described previously, I won't reverse directions at the brake lever which will mean the top of the bar is wrapped in reverse of the usual method. How likely is this to cause the tape to become lose?
3. If I clamp the brake lever down, it will be on top of the foam tape (assuming I use the foam tape I have instead of finding the cloth tape.) I am fearful the brake clamp might cut into the foam causing early failure.
4. You say to tape the clamp in place before starting. Are you meaning to tape it in place with the bar tape or some electrical tape?
Thanks
As to wrapping direction you could start at the top and work your way down. That works quite well. You end with inserting some of the bar wrap into the handlebar and then fit the end cap. Its designed to work like that.
As to the sturdiness of foam/cork wrap? Well its nowhere near as sturdy as the old style cloth tape. Everyone here is re-wrapping bars more than they used.
Anthony
#15
Great State of Varmint
Join Date: Sep 2008
Location: Dante's Third Ring
Posts: 7,476
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 15 Times
in
15 Posts
I find good cycling-gloves - with padding where your nerves are - are better for promoting a comfortable grip than thick, spongy tape, multi-layer tape, or foam. I ride Pearl Izumi Attack gloves. There are many styles of gloves out there. These are my current favorites.
#16
Senior Member
Thread Starter
Join Date: Jan 2009
Posts: 99
Bikes: 2014 Trek 7.4 FX Hybrid - Early 80s Raleigh Rapide 10 Speed
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
i have a 74 le tour w those "suicide levers". i left the levers on and had no problem wrapping my bars.
I find good cycling-gloves - with padding where your nerves are - are better for promoting a comfortable grip than thick, spongy tape, multi-layer tape, or foam. I ride Pearl Izumi Attack gloves. There are many styles of gloves out there. These are my current favorites.
My wife is laughing at me for reconditioning the old bike. She asked me if it was going to fall apart after I get it back together. I'll show her......
#18
Senior Member
Join Date: Sep 2007
Location: Vancouver
Posts: 1,437
Bikes: NOYB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
i have a 74 le tour w those "suicide levers". i left the levers on and had no problem wrapping my bars. i like to be able to change hand positions from time to time. i converted it to a single speed. feel very safe when i ride. never got the flying over the handlebar feeling. i ride my bike in the country and the city in all conditions.
#19
Rustbelt Rider
Join Date: Oct 2008
Location: Canton, OH
Posts: 9,104
Bikes: 1990 Trek 1420 - 1978 Raleigh Professional - 1973 Schwinn Collegiate - 1974 Schwinn Suburban
Mentioned: 20 Post(s)
Tagged: 0 Thread(s)
Quoted: 261 Post(s)
Liked 372 Times
in
177 Posts
I had a look at your picture and thought to myself, where are your brake hoods?
Then I remembered that those levers with the suicide levers didn't come with hoods and to be honest that changes everything. All the instructions you have read so far on bar wrapping are assuming that you have rubber hoods and NO suicide levers.
Back in the day when those levers were common cheap bikes just used a thin plastic bar wrap and expensive bikes used cloth tape which wasn't much thicker. To do a really neat wrap job with those bars and levers I would make sure the levers were positioned where I wanted them, tape the underside of the lever body clamp in place, take the lever body off, wrap the bars and when you get to the lever clamp wrap as closely as you can without interfering with the bolt hole but definitely covering the underside of the clamp and then bolting the lever body back on.
Thats the best you will do with those levers. The technique of wrapping around the lever body with it bolted in place is assuming that you will cover them with rubber hoods.
EDIT: Ohh, and I forgot to mention. Modern cork tape may not be the best to use with such levers. It just wasn't part of their design considerations. Cloth tape would give the neatest result. You may be able to bolt the lever bodies back down onto cork tape although its possible that the bolt won't reach. You will just have to see.
Anthony
Then I remembered that those levers with the suicide levers didn't come with hoods and to be honest that changes everything. All the instructions you have read so far on bar wrapping are assuming that you have rubber hoods and NO suicide levers.
Back in the day when those levers were common cheap bikes just used a thin plastic bar wrap and expensive bikes used cloth tape which wasn't much thicker. To do a really neat wrap job with those bars and levers I would make sure the levers were positioned where I wanted them, tape the underside of the lever body clamp in place, take the lever body off, wrap the bars and when you get to the lever clamp wrap as closely as you can without interfering with the bolt hole but definitely covering the underside of the clamp and then bolting the lever body back on.
Thats the best you will do with those levers. The technique of wrapping around the lever body with it bolted in place is assuming that you will cover them with rubber hoods.
EDIT: Ohh, and I forgot to mention. Modern cork tape may not be the best to use with such levers. It just wasn't part of their design considerations. Cloth tape would give the neatest result. You may be able to bolt the lever bodies back down onto cork tape although its possible that the bolt won't reach. You will just have to see.
Anthony
https://www.raydobbins.com/molteni_replica/molteni_tip
Your clamps are probably not exactly the same but it should still work. I don't wear cycling clothes either, but I do have gloves that I wear. For what it's worth, I have cork tape on my newer bike and I don't think it is as cushy as most probably imagine.
Tressostar cloth is about 4 dollars per roll and cork is usually around 12. At those prices you can buy one, try it out and replace it if you don't like it.
__________________
|^^^^^^^^^^^^^^| ||
|......GO.BROWNS........| ||'|";, ___.
|_..._..._______===|=||_|__|..., ] -
"(@)'(@)"""''"**|(@)(@)*****''(@)
|^^^^^^^^^^^^^^| ||
|......GO.BROWNS........| ||'|";, ___.
|_..._..._______===|=||_|__|..., ] -
"(@)'(@)"""''"**|(@)(@)*****''(@)
Last edited by mkeller234; 02-18-09 at 03:32 AM.
#20
Senior Member
Thread Starter
Join Date: Jan 2009
Posts: 99
Bikes: 2014 Trek 7.4 FX Hybrid - Early 80s Raleigh Rapide 10 Speed
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
I think this would be the best route cosmetically and functionally. Here is a link where Ray Dobbins demonstrates this technique with pictures:
#21
Senior Member
I've done a couple of 70s Le Tours with foam tape and it works fine. I'm sure you have the same claps as I do. They are just a strip of metal around the bar with an insert on the front side for the screw that attaches the brake housing. As noted above, make sure the clamp is where you want it; cut a short strip of the wrap and wrap it around the clamp (no need to glue, you can tape it together in the front till you get the wrap done); then wrap the bars (I prefer stem to end myself as well) and try to have your wrap just miss the top of the clamp as you go around and then drop just below the clamp on the next wrap (no bare bar visible if done right); finish off the wrap; tuck the end in; pop in the plug; and remount the brake levers over the wrap (it may take a bit of force to compress the foam enough to get the crew started but once you do it looks really clean).
#23
don't be so angry
Join Date: Sep 2004
Posts: 612
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
How much thread do you have in the suicide lever bolts? Pull them out and install a small spacer. You may have to mod the suicide lever, or find a suicide lever from another bike with more "reach" to the hood.
The other option is to adjust the levers (read - bend them a bit) Could be done without looking sloppy if you have a vice and some patience.
The other option is to adjust the levers (read - bend them a bit) Could be done without looking sloppy if you have a vice and some patience.
Last edited by clancy98; 07-28-09 at 12:58 PM.
#25
Senior Member
Join Date: Mar 2009
Location: Colorado
Posts: 9,458
Bikes: Something Canadian, something Italian, something American, and something German
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 64 Post(s)
Likes: 0
Liked 16 Times
in
10 Posts
Protip: at the shop we always remove them, wrap the bars, and then put them back on.