? on STI to DT
#1
OnTheRoad or AtTheBeach
Thread Starter
Join Date: Aug 2005
Location: Weston, FL
Posts: 2,170
Bikes: Ridley Noah RS, Scott CR1 Pro
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
? on STI to DT
So I have a backup bike which is a 9spd triple with 105 components. I managed to blow the FD STI lever and I am looking at replacing it with a DT lever. Do I need a specific DT for 9spd triple or will any lever work since I am only looking at replacing the FD? Anyone know a good source, I would prefer to keep this under $50.
Thx
Thx
__________________
The problem with the gene pool is that there is no lifeguard and the shallow end is much too large
2013 Noah RS
The problem with the gene pool is that there is no lifeguard and the shallow end is much too large
2013 Noah RS
#2
Senior Member
Join Date: Apr 2006
Location: Orange County CA
Posts: 963
Bikes: Surly CC, Raleigh Team Pro, Specialized Rockhopper with an xtracycle
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Any downtube lever will work. Although it will be in friction.
Do downtube levers come in triple indexed??
Do downtube levers come in triple indexed??
#3
OnTheRoad or AtTheBeach
Thread Starter
Join Date: Aug 2005
Location: Weston, FL
Posts: 2,170
Bikes: Ridley Noah RS, Scott CR1 Pro
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Friction is fine for the FD, anyone know a good source?
__________________
The problem with the gene pool is that there is no lifeguard and the shallow end is much too large
2013 Noah RS
The problem with the gene pool is that there is no lifeguard and the shallow end is much too large
2013 Noah RS
#4
Senior Member
Join Date: Apr 2006
Location: Orange County CA
Posts: 963
Bikes: Surly CC, Raleigh Team Pro, Specialized Rockhopper with an xtracycle
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I'm sure you can get a nice set of suntour or simplex retrofriction shifters on ebay. They are supposed to be one of the best friction levers made. I recall in 89, Greg Lemond had a full Campy setup but didn't use the crappy Synchro II shifters but instead stuck with the simplex.
On a similar note, does your current ride have downtube braze-ons to accomodate a shifter? You might want to ask in the mechanics section about downtube compatibility. I've heard in the past of some sort of shimano propriorty braze-on mount where you would need an extra sleeve/washer if you went the suntour/simplex route. Then again, you can always find any shimano left dt shifter. If you don't have dt braze-ons but only brazed on barrels for your STIs, you might want to get a barend shifter instead...or even some sort of thumbshifter??
I dont think you need to replace your FD unless you damaged that as well.
Here you go..
https://cgi.ebay.com/SHIMANO-DOWN-TUB...d=p3286.c0.m14
On a similar note, does your current ride have downtube braze-ons to accomodate a shifter? You might want to ask in the mechanics section about downtube compatibility. I've heard in the past of some sort of shimano propriorty braze-on mount where you would need an extra sleeve/washer if you went the suntour/simplex route. Then again, you can always find any shimano left dt shifter. If you don't have dt braze-ons but only brazed on barrels for your STIs, you might want to get a barend shifter instead...or even some sort of thumbshifter??
I dont think you need to replace your FD unless you damaged that as well.
Here you go..
https://cgi.ebay.com/SHIMANO-DOWN-TUB...d=p3286.c0.m14