Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Building a super strong rear wheel

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Building a super strong rear wheel

Old 08-19-09, 12:37 AM
  #1  
Senior Member
Thread Starter
 
Join Date: Aug 2008
Posts: 536
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times in 1 Post
Building a super strong rear wheel

I have a canadian tire schwinn Izip, which is basically a Currie Ezip that Dorel Canada has stamped their own name on.

I have less than 1000 kms of commuting on it, and I noticed that there are 4 spokes broken on the rear wheel they are all right next to each other and broke at the hub, not the rim.

When I took it to the local bike shop, they told me that the spokes were already the strongest spokes that you can get, and they didn't seem optimistic that a different rim would help.

Has anyone had their rear wheel rebuild with specialty parts that make it super strong? what parts did you use?

There is a local bike shop in town that is also a good motorcycle shop, I'm thinking that the 2 shops can collaberate to make an extra strong wheel for me, but I am curious if someone can recommend their build?

thanks in advance.

TS
SeizeTech is offline  
Old 08-19-09, 02:19 AM
  #2  
AEO
Senior Member
 
AEO's Avatar
 
Join Date: Jun 2007
Location: A Coffin Called Earth. or Toronto, ON
Posts: 12,258

Bikes: Bianchi, Miyata, Dahon, Rossin

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 5 Times in 5 Posts
did the spokes snap on the drive side or the non-drive side?
snapping at the hub side usually means spoke metal fatigue, which leads to not enough spoke tension when the wheel was first built up.

I'd recommend having the wheel rebuilt with 2.0/1.8/2.0mm double butted spokes and brass nipples.
and if the wheel builder can do it, tie solder the non drive side spokes.
__________________
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
AEO is offline  
Old 08-19-09, 02:20 AM
  #3  
Senior Member
 
Join Date: Mar 2008
Posts: 8,688
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 295 Times in 222 Posts
Originally Posted by SeizeTech
I have a canadian tire schwinn Izip, which is basically a Currie Ezip that Dorel Canada has stamped their own name on.
Doing some googling but can't determine which bike it is that you have. Post a pic or a link to a pic. We need to know more about the wheel and the drive assembly to be able to say something specific.

Originally Posted by SeizeTech
I have less than 1000 kms of commuting on it, and I noticed that there are 4 spokes broken on the rear wheel they are all right next to each other and broke at the hub, not the rim.
That's where they usually break. Which side, drive side or non-drive side?

Originally Posted by SeizeTech
...When I took it to the local bike shop, they told me that the spokes were already the strongest spokes that you can get,
Strong in everyday terms is too fuzzy when you get down to detailed engineering questions. Since your spokes held up in the beginning the issue you're dealing with is fatigue - not "strength". When it comes to pure pulling power spokes are just about always more than strong enough. Nipples and rims tends to fail way before the spoke is torn apart.

Originally Posted by SeizeTech
..When I took it to the local bike shop, ... they didn't seem optimistic that a different rim would help.
If most characteristics of you, your bike and your riding are "average", then it's unlikely that it's the rim that's at fault.
What could happen though is if you have a rim that has a bad low spot, then the builder might have prioritized roundness above spoke tension. This can leave you with a group of spokes that are badly undertensioned, and they will fail due to fatigue rather rapidly. In this situation replacing the rim would help. What you need in that case isn't a stronger rim, but merely a rounder one.

Originally Posted by SeizeTech
Has anyone had their rear wheel rebuild with specialty parts that make it super strong?
Sure, but unless there's something "special" about the rest of the situation there's usually an easier fix to the problem. Most rear wheel issues is down to build quality rather than parts quality.
If your issue is fatigue related, then tension, tension and tension are the most important keywords. There is a bunch of tricks that can be used, but we need to kow more about the drivetrain and the wheel to be able to say which can be used by you.
Is it a stock hub?
How many spokes?
how many crosses?
what gauges?
how is the drive arranged?

What do you mean by "strong"? capable of taking endless mileage or capable of carrying huge loads w/o buckling? These two are kinda mutually exclusive.

Originally Posted by SeizeTech
There is a local bike shop in town that is also a good motorcycle shop, I'm thinking that the 2 shops can collaberate to make an extra strong wheel for me, but I am curious if someone can recommend their build?
Well I'm not saying it's impossible, but it'd probably be hopelessly expensive. A bicycle hub can't be drilled for motorcycle spokes, the flanges aren't big enough. There's nothing preventing a good metal fabricator from replacing the flanges, which'd immediately leave you with the issue of finding a rim that could be redrilled to take the thicker nipples. There are probably wide section DH rims that are meaty enough for such a procedure, but unless there's something extreme that you aren't telling us about your riding situation you really shouldn't need it to get a functional wheel.

My money is on a poor build quality. Get the wheel rebuilt to the proper spoke tension. If there's problem with the rim it should surface then and if needed you can have it replaced.
dabac is offline  
Old 08-19-09, 03:58 AM
  #4  
Senior Member
 
Retro Grouch's Avatar
 
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225

Bikes: Catrike 559 I own some others but they don't get ridden very much.

Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 642 Times in 363 Posts
I agree with dabac.

A tension spoked bicycle wheel has 4 components: hub, spokes, rim and build quality. The typical 32 spoke 3 cross wheel, when well constructed, is so reliable that manufacturers are generally looking for ways to make it lighter rather than to make it stronger.
Retro Grouch is offline  
Old 08-19-09, 05:39 AM
  #5  
All-round nice guy.
 
Mike T.'s Avatar
 
Join Date: May 2005
Location: Ontario Canada
Posts: 448

Bikes: Kish road bike, Seven mtb, Marinoni road and track bikes.

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Along with the other posters I agree that the problem lies with build quality rather than parts choice. The wheel would have had insufficient tension and unequal tensions. Those two things are the biggest factors in the longevity of a wheel and they are both as equal.

Machine-built wheels (as are on your bike) are notorious for poorly tensioned wheels. This leads to early metal fatigue.

2.0/1.8/2.0mm gauge of spoke will be ideal and will also absorb shock loads better than a 2.0mm plain gauge spoke and thus will give a wheel that can absorb better. Spokes like DT Competition and Sapim Race are ideal and very high quality.

Find a good wheelbuilder and get them to re-build with new spokes. Of course finding a wheelbuilder is easy but finding a good one is a lot harder. You could even do it yourself and with the correct information you could do a better job than a poor "wheelbuilder".

Read my wheelbuilding tips and you will gain the knowledge for what is needed in a search for a good builder or for doing the job yourself. The link to Roger Musson's wheelbuilding e-book at the end of my info would be the best click you could place.
Mike T. is offline  
Old 08-19-09, 11:17 AM
  #6  
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,934

Bikes: Several, mostly not name brands.

Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3571 Post(s)
Liked 3,366 Times in 1,915 Posts
Originally Posted by dabac
Strong in everyday terms is too fuzzy when you get down to detailed engineering questions. Since your spokes held up in the beginning the issue you're dealing with is fatigue - not "strength". When it comes to pure pulling power spokes are just about always more than strong enough. Nipples and rims tends to fail way before the spoke is torn apart.
Agreed. Unless this is a low spoke count wheel (doubtful from Canadian Tire) your spokes and rim are likely more than adequate strength. Fatigue failure of spokes is almost exclusively due to low spoke tension, and I suspect a Canadian Tire bike would have machine-built wheels and probably not retensioned since they left the factory.

AT this point my recommendation would be to tear the wheel down and rebuild it with all new spokes. Make sure the rim is not damaged, as this would be the ideal time to replace it if it is. If the rim (or hub) is damaged, you may wish to consider a replacement wheel, preferably built, or at least retensioned by your LBS staff.
JohnDThompson is offline  
Old 08-19-09, 12:52 PM
  #7  
Senior Member
 
Join Date: Feb 2005
Location: Oklahoma
Posts: 9,438

Bikes: Trek 5500, Colnago C-50

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 7 Times in 6 Posts
The DT Swiss Alpine III spokes are triple butted and thicker at the hub end, 2.34-1.8-2.0. I don't know if they are compatible with your hub though. https://www.dtswiss.com/getdoc/02e74b...Datasheet.aspx

And I agree with the others, your spoke failure sounds like insufficient tension.

Al

Last edited by Al1943; 08-19-09 at 12:57 PM.
Al1943 is offline  
Old 08-19-09, 02:47 PM
  #8  
Senior Member
Thread Starter
 
Join Date: Aug 2008
Posts: 536
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times in 1 Post
I'd like to thank everyone for their help and support.

I took the wheel to a specialty shop today, and I'm having them hand build the wheel with a new set of spokes and a double walled deep V rim that is rated for riders that like to take lots of jumps. My hub is a custom hub that has a sprocket on one side, and a 7 sprocket gear set on the other side, so it will be the only thing that will remain the same.

At the end of the day, I'll have spend about $200 but I'm commited to making are really good wheel.

I am totally ok with the possibility that this is all a waste of money, and maybe 4 new spokes and a retensioning would have sufficed. I'm expecting to be happy with my new wheel regardless.
SeizeTech is offline  
Old 08-19-09, 03:05 PM
  #9  
Type 1 Racer
 
rydaddy's Avatar
 
Join Date: Apr 2006
Location: Davis, CA
Posts: 2,579

Bikes: A dozen or so.

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by JohnDThompson
Fatigue failure of spokes is almost exclusively due to low spoke tension
Just to add a bit there... failure to stress relieve, or not correcting the spoke line will cause fatigue failures just as quickly. Just sayin, it's not always about low tension.
rydaddy is offline  
Old 08-19-09, 03:07 PM
  #10  
Type 1 Racer
 
rydaddy's Avatar
 
Join Date: Apr 2006
Location: Davis, CA
Posts: 2,579

Bikes: A dozen or so.

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by SeizeTech
I am totally ok with the possibility that this is all a waste of money
I'm thinking it won't be a waste of money.
rydaddy is offline  
Old 08-19-09, 04:58 PM
  #11  
Senior Member
 
Join Date: Mar 2008
Location: Chicago, IL, USA
Posts: 307

Bikes: 1974 Raleigh Sports

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Yeah, I've seen this happen before. I agree with all who say it's the build. My friend's rear wheel broke a few spokes, and she had the hack LBS replace them...and then even more broke than the first time, etc., etc. When she showed me the wheel, lots (10 or so) of spokes were broken. I took the wheel and rebuilt it (reusing rim and hub) with new DT 14/15/14 spokes. She paid me back the $40 for the two boxes of spokes and in brownie points for the labor. She's ridden the rebuilt wheel for over a year now with no complaints.

Build is super important.
FLYcrash is offline  
Old 08-19-09, 04:59 PM
  #12  
Real Men Ride Ordinaries
 
fuzz2050's Avatar
 
Join Date: Sep 2008
Posts: 3,723
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 17 Post(s)
Likes: 0
Liked 3 Times in 3 Posts
Originally Posted by SeizeTech
My hub is a custom hub that has a sprocket on one side, and a 7 sprocket gear set on the other side, so it will be the only thing that will remain the same.

Sounds like you have your problem solved, now can we get a photo of that hub?
fuzz2050 is offline  
Old 08-19-09, 10:39 PM
  #13  
Senior Member
Thread Starter
 
Join Date: Aug 2008
Posts: 536
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times in 1 Post
I don't have a photo of my hub, but I was able to find this pic on google. but
It is definitely the same as my hub.

I'm sorry for the lack of views. What you are seeing is the left side of the rear hub, on the right side there is a 7 sprocket gear set for human powered riding.
Attached Images
File Type: jpg
2853447852_d263f067ff.jpg (37.0 KB, 30 views)

Last edited by SeizeTech; 08-19-09 at 10:47 PM.
SeizeTech is offline  
Old 08-19-09, 10:44 PM
  #14  
Senior Member
Thread Starter
 
Join Date: Aug 2008
Posts: 536
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times in 1 Post
here's another view, but this guy has modified the electric bracket to accomodate 2 motors. The stock bikes only have 1 motor. In fact, I was shocked to see this. Its not something that I've seen before.
Attached Images
File Type: jpg
3006606858_31fe47d55c.jpg (50.7 KB, 24 views)
SeizeTech is offline  
Old 08-19-09, 11:10 PM
  #15  
Senior Member
Thread Starter
 
Join Date: Aug 2008
Posts: 536
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times in 1 Post
my invoice says "New DT Swiss Spokes 2.0 Silver Lace to new 721"

does that give you any indication of what he sold me?

edit: looks like DT Swiss spokes and a Mavic 721 downhill mtnbike rim

is it any good?

Last edited by SeizeTech; 08-19-09 at 11:14 PM.
SeizeTech is offline  
Old 08-19-09, 11:56 PM
  #16  
Senior Member
 
DannoXYZ's Avatar
 
Join Date: Jul 2005
Location: Saratoga, CA
Posts: 11,736
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 109 Post(s)
Liked 9 Times in 6 Posts
It should be fine. Would've been better to get double-butted spokes or the triple-butted ones Al1943 mentioned.


If you are using an electric motor to drive the bike, that's definitely a contributor to the broken spokes.

What's the HP-rating of the motor?
What's the gearing-ratio?
How is the throttle controlled?
Is it linked to the brakes?
DannoXYZ is offline  
Old 08-20-09, 03:08 AM
  #17  
Senior Member
 
Join Date: Mar 2008
Posts: 8,688
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 295 Times in 222 Posts
Originally Posted by SeizeTech
I don't have a photo of my hub, but I was able to find this pic on google. but
It is definitely the same as my hub.

Ther are any number of small reasons that might make it impossible, but a hub much like that could easily be put together by taking a stock disc brake (free)hub and then putting a tomicog (a special sprocket) in place of the brake rotor. Lace to a rim with with brake surfaces and you're good to go.
dabac is offline  
Old 08-20-09, 03:11 AM
  #18  
Senior Member
 
Join Date: Mar 2008
Posts: 8,688
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 295 Times in 222 Posts
Originally Posted by Retro Grouch
..A ....bicycle wheel has 4 components: hub, spokes, rim and build quality. ....
That's a very neat way of putting it
dabac is offline  
Old 08-20-09, 07:43 AM
  #19  
Senior Member
Thread Starter
 
Join Date: Aug 2008
Posts: 536
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times in 1 Post
Originally Posted by DannoXYZ
It should be fine. Would've been better to get double-butted spokes or the triple-butted ones Al1943 mentioned.


If you are using an electric motor to drive the bike, that's definitely a contributor to the broken spokes.

What's the HP-rating of the motor?
What's the gearing-ratio?
How is the throttle controlled?
Is it linked to the brakes?
thanks. 450W motor, I think my legs can deliver 600W but only for a short sprint. i would decribe my legs as 150W continous output. the motor adds an extra 5 mph to my speed, and provides me with a much wider range of comfotable cruising speed

the throttle is a twist grip, and the brake levers have a cut out switch which is so popular that it is considered a manditory safety feature in many areas of north america.

gear ratio, its a fixed gear as a dc motor can deliver a fair amount of torque even when it isn't at an efficient operating speed. the ratio reduces the 3000 rpm t0 about 260 rpm. (i think)
SeizeTech is offline  
Old 08-20-09, 01:16 PM
  #20  
Senior Member
 
rumrunn6's Avatar
 
Join Date: Jul 2008
Location: 25 miles northwest of Boston
Posts: 29,520

Bikes: Bottecchia Sprint, GT Timberline 29r, Marin Muirwoods 29er, Trek FX Alpha 7.0

Mentioned: 112 Post(s)
Tagged: 0 Thread(s)
Quoted: 5218 Post(s)
Liked 3,564 Times in 2,331 Posts
you might consider a rear wheel from a tandem bike. I hear they are wicked strong w/ 46 spokes cuz they're built to hold up 2 people!
rumrunn6 is offline  
Old 08-20-09, 03:06 PM
  #21  
AEO
Senior Member
 
AEO's Avatar
 
Join Date: Jun 2007
Location: A Coffin Called Earth. or Toronto, ON
Posts: 12,258

Bikes: Bianchi, Miyata, Dahon, Rossin

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 5 Times in 5 Posts
Originally Posted by rumrunn6
you might consider a rear wheel from a tandem bike. I hear they are wicked strong w/ 46 spokes cuz they're built to hold up 2 people!
that's either a 40 or 48 spoke.
spoke count is always a multiple of 4, not including 18h.
__________________
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
AEO is offline  
Old 08-21-09, 05:48 AM
  #22  
A little North of Hell
 
Join Date: Mar 2006
Posts: 4,892
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 71 Post(s)
Likes: 0
Liked 4 Times in 4 Posts
Originally Posted by AEO
that's either a 40 or 48 spoke.
spoke count is always a multiple of 4, not including 18h.
or, 21 and 27 on the rear.

or, 22 and 26 on the front.
Soil_Sampler is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.