what spoke length do i need?
09-26-09, 04:58 PM
#1
Member
Thread Starter
Join Date: Aug 2009
Posts: 37
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
what spoke length do i need?
I want to lace a weinmann dp-18 to a formula high flange track hub, 36 holes, 3 cross. what length spokes should i order?
09-26-09, 05:34 PM
#2
Senior Member
Join Date: Jun 2007
Location: A Coffin Called Earth. or Toronto, ON
Posts: 12,257
Bikes: Bianchi, Miyata, Dahon, Rossin
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 5 Times
in
5 Posts
you'll have to do a few measurements for the answer to that.
ERD for DP-18 is 585mm and you use 12mm nipples.
now all you need to figure out are flange diameter and center to flange.
ERD for DP-18 is 585mm and you use 12mm nipples.
now all you need to figure out are flange diameter and center to flange.
__________________
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
09-26-09, 06:27 PM
#4
Senior Member
Join Date: Dec 2007
Location: San Jose, California
Posts: 3,504
Bikes: 2001 Tommasini Sintesi w/ Campagnolo Daytona 10 Speed
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 145 Post(s)
Likes: 0
Liked 35 Times
in
30 Posts
Assuming front hub:
r = 62.0 mm
c = 34
Assuming rear hub (double fixie):
r = 62.0 mm
c = 31.5 mm
Front = 276.40 @ 276.00 mm
Rear = 276.10 @ 276.00 mm
=8-)
Assumes 14g or 14g/15g/14g spokes w/ 10mm threads and 12mm nipples or w/ 12mm threads and 16 mm nipples.
r = 62.0 mm
c = 34
Assuming rear hub (double fixie):
r = 62.0 mm
c = 31.5 mm
Front = 276.40 @ 276.00 mm
Rear = 276.10 @ 276.00 mm
=8-)
Assumes 14g or 14g/15g/14g spokes w/ 10mm threads and 12mm nipples or w/ 12mm threads and 16 mm nipples.
09-26-09, 06:29 PM
#5
Senior Member
Join Date: Dec 2007
Location: San Jose, California
Posts: 3,504
Bikes: 2001 Tommasini Sintesi w/ Campagnolo Daytona 10 Speed
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 145 Post(s)
Likes: 0
Liked 35 Times
in
30 Posts
16mm nipples will not work on 10mm threads in my calculation unless you verify the 16mm nipples actually allow 10mm threaded spokes all the way to the top of the nipple before assembling the wheel.
09-26-09, 06:41 PM
#6
Senior Member
Join Date: Dec 2007
Location: San Jose, California
Posts: 3,504
Bikes: 2001 Tommasini Sintesi w/ Campagnolo Daytona 10 Speed
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 145 Post(s)
Likes: 0
Liked 35 Times
in
30 Posts
ERD for Weinman DP-18:
Short (Aiming at or just below nipple flat) = 578 mm
Long (Aiming at or just past the nipple flat) = 579 mm
=8-)
Short (Aiming at or just below nipple flat) = 578 mm
Long (Aiming at or just past the nipple flat) = 579 mm
=8-)
