how NOT to remove a stuck seatpost
#1
Member
Thread Starter
Join Date: Nov 2009
Location: KS
Posts: 36
Bikes: fuji, specialized, sanwa
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
how NOT to remove a stuck seatpost
the worst part? ...it's still stuck. i stopped caring about the frame (obviously) or the post long ago, all i'm after now is victory.
DON'T TRY THIS AT HOME... or anywhere for that matter.
Anyway I'm michael from KS, nice to meet you all. Don't worry, I do know how to use a few tools besides hacksaws and hammers.
#2
spathfinder34089
Join Date: Jun 2007
Location: Washington State
Posts: 200
Bikes: fuji s12s, Schwiin Le Tour, Puegot mtn. bike, Hiawatha crusier
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
O.k. get a can of penetrating oil. Not WD40 and soak the post real good. If you can't get it to go down on top then take out the bottom bracket and go that way. Let it soak in for a few hours. Get a wrench like a large channel lock that reall grips the post and twist back and forth till it moves. If you don't care about the frame and just want victory get a torch and hit up the part that the post goes into and that will loosen it up. It will ruin your paint job though.
#4
Senior Member
Join Date: Jul 2005
Location: New Haven, CT area
Posts: 1,415
Bikes: Trek 7.5 Hybrid, Trek 1.1 Road, Holdsworth touring,Raleigh International,Ritchey Commando,Italvega Speciallissimo,et.al.
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 10 Times
in
10 Posts
I , also, have never ever seen this new and upgraded method of stuck seat post removal. My last resort always was to clamp the seat post in a vise and twist the frame from side to side, even if I had to crush the crap out of the seat post, just to get it out. Never seen the fork method, though.
#7
Senior Member
Join Date: Oct 2005
Location: Fresno, CA
Posts: 4,454
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 128 Post(s)
Likes: 0
Liked 12 Times
in
10 Posts
when you weren't looking, someone slipped epoxy into the seatpost-seat tube contact area
__________________
"c" is not a unit that measures tire width
"c" is not a unit that measures tire width
#10
Dave
Join Date: Jan 2006
Location: Homestead FL
Posts: 685
Bikes: Nashbar X-Cross 29r wheels front disc brake
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
What will you do when the extension tube on your repair stand gets stuck?
#11
Senior Member
Join Date: Oct 2005
Location: Fresno, CA
Posts: 4,454
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 128 Post(s)
Likes: 0
Liked 12 Times
in
10 Posts
but I think the OP's method looks more fun
__________________
"c" is not a unit that measures tire width
"c" is not a unit that measures tire width
#14
Senior Member
Join Date: Jul 2006
Location: Columbus, OH
Posts: 11,375
Bikes: '08 Surly Cross-Check, 2011 Redline Conquest Pro, 2012 Spesh FSR Comp EVO, 2015 Trek Domane 6.2 disc
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 5 Post(s)
Likes: 0
Liked 7 Times
in
6 Posts
I , also, have never ever seen this new and upgraded method of stuck seat post removal. My last resort always was to clamp the seat post in a vise and twist the frame from side to side, even if I had to crush the crap out of the seat post, just to get it out. Never seen the fork method, though.
__________________
"I feel like my world was classier before I found cyclocross."
- Mandi M.
"I feel like my world was classier before I found cyclocross."
- Mandi M.
#15
Super Moderator
Join Date: Jul 2004
Location: Ffld Cnty Connecticut
Posts: 21,845
Bikes: Old Steelies I made, Old Cannondales
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 1173 Post(s)
Liked 924 Times
in
610 Posts
Maybe a mechanic with a bottle of Elmer's glue ?
__________________
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
Bikes: Old steel race bikes, old Cannondale race bikes, less old Cannondale race bike, crappy old mtn bike.
FYI: https://www.bikeforums.net/forum-sugg...ad-please.html
#16
aka: Dr. Cannondale
Join Date: Jul 2009
Posts: 7,852
Mentioned: 234 Post(s)
Tagged: 0 Thread(s)
Quoted: 2151 Post(s)
Liked 3,380 Times
in
1,198 Posts
Use a Dremel or power grinder to slot the seat tube down the side for 6-8 inches. That'll loosen 'er up.
And I would not suggest wailing away with a hammer on a bike that's in a Park stand. Instead, support it on a workbench over a 2X4 or two. Your stand will last longer and the impact of your hammer will be more effective.
And I would not suggest wailing away with a hammer on a bike that's in a Park stand. Instead, support it on a workbench over a 2X4 or two. Your stand will last longer and the impact of your hammer will be more effective.
#17
Solo Rider, always DFL
Join Date: Jun 2006
Location: Beacon, NY
Posts: 2,004
Bikes: Cannondale T800, Schwinn Voyageur
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
That must be one hell of a nice seatpost to be worth that amount of effort
#18
Senior Member
Join Date: Jun 2007
Location: A Coffin Called Earth. or Toronto, ON
Posts: 12,258
Bikes: Bianchi, Miyata, Dahon, Rossin
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 5 Times
in
5 Posts
could have just tossed the thing into ammonia. (it'll dissolve the aluminum)
__________________
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
#19
Member
Thread Starter
Join Date: Nov 2009
Location: KS
Posts: 36
Bikes: fuji, specialized, sanwa
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I know, total stupid overkill. no it's not a nice post, and the frame is about 45% rust but everytime i walked by i could hear it... mocking me. i was after the post for my winter bike build so the priority was to preserve the post if possible at the frame's expense. tried soaking in ammonia, coca cola, pblaster, no luck. I did however find a little rusty piece of paper inside the seat tube after i cut it open with a previous owners name, address, ph # and serial #'s. Thinking about sending him a letter of apology
good advice rccardr. I will try that next, I haven't quite given up yet, even though the post is probably unusable at this point. I did actually get it to rotate a little bit with a pipe wrench on the head of the post and the headtube of another junk frame on the wrench for leverage (just moved in, vice isn't installed yet. frames make surprisingly good cheaters) and started the dance of victory when i realized... the clamp was just rotating on the post! Gar! I think that's when the saw came out.
And Gene, I should have some better cantilevers than those in the basement if you do need a set.
good advice rccardr. I will try that next, I haven't quite given up yet, even though the post is probably unusable at this point. I did actually get it to rotate a little bit with a pipe wrench on the head of the post and the headtube of another junk frame on the wrench for leverage (just moved in, vice isn't installed yet. frames make surprisingly good cheaters) and started the dance of victory when i realized... the clamp was just rotating on the post! Gar! I think that's when the saw came out.
And Gene, I should have some better cantilevers than those in the basement if you do need a set.
#20
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times
in
741 Posts
Had to do this with an '88 Trek 400 I salvaged from a dumpster around this time last year. Post was stuck solid and not moving; it was hard to believe it was the right size post to begin with... felt more like someone had just hammered a 27.2 into a 27.0 with how bad it was stuck. Many applications of WD40 and Liquid Wrench, plus generous brute force finally got the darned thing out.
#21
Senior Member
Join Date: Jul 2005
Location: New Haven, CT area
Posts: 1,415
Bikes: Trek 7.5 Hybrid, Trek 1.1 Road, Holdsworth touring,Raleigh International,Ritchey Commando,Italvega Speciallissimo,et.al.
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Likes: 0
Liked 10 Times
in
10 Posts
Now that I think about it, removing stuck seat posts was probably the most frustrating and incredibly time consuming repair jobs that I ever did. If a freewheel would not come off the hub, I could always just take off the individual cogs, clamp the body in a vise, and voila, get it off. However, stuck seat posts, like the original poster, sometimes became 3 to 5 day battles of wills, or wits. I guess it is sort of like man versus machine, sort of. You know that it is there, right in front of you, and challenging you to get it the heck out. Once you start removing the crankset and pouring various liquids down the seat tube, it starts getting might personal. By the way, I do recollect some very funky 27.0/27.2 Trek seat posts problems-bad fits. Could have been the seat post diameter being off a bit, but I really think that the problem was either the tubing/paint or contamination in the tubing, or seat post tubing not bored out correctly. Just enough of a problem to be a pain.
#22
Senior Member
Join Date: Sep 2009
Location: Grayslake, IL
Posts: 54
Bikes: '74 Ral SuperCourse II, '77? Ron Cooper, '82 Scapin Sprint?, '84 Ross Sig, '86 Voyageur, '86 Miy. 512, '87 Prologue, '87 Circuit, '91 MP21, '96? DeBernardi, '14 Dolan Mythos, Giordano Tandem, '18 Masi Alare.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Liked 1 Time
in
1 Post
Possiblecrit, THANK YOU for making my day! Now I'm ready to go out in that nasty Chicago weather!
Charles
Charles
#23
Friendship is Magic
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,932
Bikes: old ones
Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26249 Post(s)
Liked 10,231 Times
in
7,100 Posts
Classic Get A Bigger Hammer Situation
the worst part? ...it's still stuck. i stopped caring about the frame (obviously) or the post long ago, all i'm after now is victory.
DON'T TRY THIS AT HOME... or anywhere for that matter.
Anyway I'm michael from KS, nice to meet you all. Don't worry, I do know how to use a few tools besides hacksaws and hammers.
Also. it's a little difficult to tell from the photo,
but the physics of the situation would seem to
call for some other frame support?
If all that's holding it is the park clamp, you're
losing a great deal of your angry energy in
flex. And you started out with too small a
hammer anyway.
__________________
#24
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times
in
741 Posts
Also. it's a little difficult to tell from the photo,
but the physics of the situation would seem to
call for some other frame support?
If all that's holding it is the park clamp, you're
losing a great deal of your angry energy in
flex. And you started out with too small a
hammer anyway.
Also, note to CharlesP: If you are riding in the winter in the Chicago area, be sure to grease your seatpost thoroughly at least a couple of times a year so you don't have to start a new thread like this one.
#25
Friendship is Magic
Join Date: Nov 2010
Location: Sacramento, CA
Posts: 22,932
Bikes: old ones
Mentioned: 304 Post(s)
Tagged: 0 Thread(s)
Quoted: 26249 Post(s)
Liked 10,231 Times
in
7,100 Posts
Uh, you guys do realize this thread was started over two years ago don't you?
Also, note to CharlesP: If you are riding in the winter in the Chicago area, be sure to grease your seatpost thoroughly at least a couple of times a year so you don't have to start a new thread like this one.
Also, note to CharlesP: If you are riding in the winter in the Chicago area, be sure to grease your seatpost thoroughly at least a couple of times a year so you don't have to start a new thread like this one.
__________________