Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

36 Spoke lacing: 3 cross vs 4 cross?

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

36 Spoke lacing: 3 cross vs 4 cross?

Old 08-23-04, 02:38 PM
  #1  
Senior Member
Thread Starter
 
rykoala's Avatar
 
Join Date: May 2004
Posts: 2,013
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
36 Spoke lacing: 3 cross vs 4 cross?

Subject says it. When inquiring to the LBS about a stronger wheel, they suggested a 36 spoke wheel laced 4 cross. This being for a 26" rear wheel. According to them the 4 cross pattern is stronger. Any word on this, wheelbuilders among us?
rykoala is offline  
Old 08-23-04, 03:17 PM
  #2  
The Red Lantern
 
Rev.Chuck's Avatar
 
Join Date: Apr 2003
Location: Raleigh NC
Posts: 5,965
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Unless the hub flange is pretty big the spokes will make their first cross over the end of another spoke. This makes a high stress point( i have seen them break here) Three cross should be plenty strong.
__________________
Are you a registered member? Why not? click here to register. Its free, and only takes 27 seconds!
Help out the forums, abide by our community guidelines.

I am in the woods and I have gone crazy.
Rev.Chuck is offline  
Old 08-23-04, 03:34 PM
  #3  
Senior Member
 
Join Date: Mar 2004
Location: Colorado
Posts: 240
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
According to the wheel building book I have, yes cross four is stronger.

I have never seen one laced this way so I can't responed to the above post about the stress point.
karlfitt is offline  
Old 08-23-04, 04:06 PM
  #4  
cycles per second
 
Gonzo Bob's Avatar
 
Join Date: Oct 2003
Location: Minnesota
Posts: 1,930

Bikes: Early 1980's Ishiwata 022 steel sport/touring, 1986 Vitus 979, 1988 DiamondBack Apex, 1997 Softride PowerWing 700, 2001 Trek OCLV 110

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 44 Post(s)
Liked 71 Times in 48 Posts
My mountain bike wheels came 36 hole built cross 4. I don't recommend it. The spokes partially overlap the adjacent spoke head. In addition to weakening the overlapping spoke at this location, it also makes it really hard to remove a spoke when you break one.

A higher cross pattern for a given spoke count will make a wheel that's better at withstanding hub twist up forces but it will also be slightly weaker for side loads - i.e. may go out of true more.
Gonzo Bob is offline  
Old 08-23-04, 04:26 PM
  #5  
Senior Member
Thread Starter
 
rykoala's Avatar
 
Join Date: May 2004
Posts: 2,013
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Hmmm OK. Where does a guy get a wheel that can handle high weight, and be super strong still? I don't want to have to worry about knocking a wheel out of true anymore...
rykoala is offline  
Old 08-23-04, 09:07 PM
  #6  
Senior Member
 
Join Date: Sep 2001
Location: Montreal
Posts: 6,521

Bikes: Peugeot Hybrid, Minelli Hybrid

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 2 Times in 2 Posts
Get a deep (30 mm) double walled rim. Have it built up with 36 14/15 butted spokes, as the thinner middle section will stretch more under shock loads, to give a more resilient wheel.
AndrewP is offline  
Old 08-23-04, 09:18 PM
  #7  
feros ferio
 
John E's Avatar
 
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,764

Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;

Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1384 Post(s)
Liked 1,294 Times in 819 Posts
In the early 1970s, most European high-flange wheels were laced 3X, but the Japanese popularized 4X. (English 3-speeds traditionally had 32 spokes 3X, low flange, in front, and 40 spokes 4X, high flange, in back.)

On the front wheel, I doubt it makes any real difference, so I generally use 3X, which is slightly quicker to build. On the rear, 4X spokes are more nearly tangential to the hub flange than 3X, and are therefore theoretically subject to reduced windup/torque stress. Again, in practice, I am not convinced it makes any significant difference.

As to maximizing wheel strength-to-weight ratio, the more spokes, the better.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
John E is offline  
Old 08-23-04, 10:00 PM
  #8  
Senior Member
 
Join Date: Jun 2003
Posts: 16,771
Mentioned: 125 Post(s)
Tagged: 0 Thread(s)
Quoted: 1454 Post(s)
Liked 85 Times in 40 Posts
Originally Posted by rykoala
Hmmm OK. Where does a guy get a wheel that can handle high weight, and be super strong still? I don't want to have to worry about knocking a wheel out of true anymore...
An LBS with a wheel-builder who know what s/he is doing and talking about.
Rowan is offline  
Old 08-23-04, 10:09 PM
  #9  
Senior Member
 
shecky's Avatar
 
Join Date: Nov 2003
Location: Home of the Homeless
Posts: 610

Bikes: Rustbuckets, the lot of them.

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
If you must have stonger wheels, perhaps you could find some tandem 40 or 48 spoke rim/hub combos.

A 36/cross 3 wheel is pretty damn strong. I think much of that strength is compromised with modern 8+ gear clusters, when the wheel is dished so much.

I wonder if there are high end options for 12g spokes, like I've seen on some heavy duty Worksman bikes?
shecky is offline  
Old 08-23-04, 10:35 PM
  #10  
Senior Member
Thread Starter
 
rykoala's Avatar
 
Join Date: May 2004
Posts: 2,013
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
So is this an argument for a purpose built single speed wheel, with a bmx freewheel?
rykoala is offline  
Old 08-24-04, 08:08 AM
  #11  
feros ferio
 
John E's Avatar
 
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,764

Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;

Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1384 Post(s)
Liked 1,294 Times in 819 Posts
Originally Posted by rykoala
So is this an argument for a purpose built single speed wheel, with a bmx freewheel?
Regarding wheel strength: 1) The more spokes, the better. 2) The less dish offset/asymmetry, the better. The latter is why mountain bikes tend to have wider rear triangles than road bikes, for a given number of cogs. If you need maximum strength on a road wheel, without giving up your gears, consider custom-spacing and custom-dishing with, say, a 7-speed freewheel/freehub on a 130 or 135mm overlock axle, assuming your frame can safely handle the spacing. (Just be sure to tighten your low gear limit screw far enough to keep your rear derailleur and/or chain out of your spokes!)
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
John E is offline  
Old 08-24-04, 11:28 AM
  #12  
I drink your MILKSHAKE
 
Raiyn's Avatar
 
Join Date: Jul 2002
Location: St. Petersburg, FL
Posts: 15,061

Bikes: 2003 Specialized Rockhopper FSR Comp, 1999 Specialized Hardrock Comp FS, 1971 Schwinn Varsity

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 3 Times in 3 Posts
It would be better to do 4X with a disc hub due to it's larger flange, thereby mitigating the potential stress point. Having said that my 32 spoke Rhynolites laced up three cross have been just fine for this Clydesdale.
__________________
Raiyn is offline  
Old 08-24-04, 02:07 PM
  #13  
Breaker of Spokes
 
P. B. Walker's Avatar
 
Join Date: Aug 2002
Location: N. Virginia
Posts: 493
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I had a 4 cross road bike wheel and had nothing but trouble with it. Spokes were always coming loose or breaking. I was in the LBS every weekend to get the wheel fixed or spokes tightened. I went to another wheel builder who stated emphatically that I should have never gone with a 4 cross pattern. He then built me a set with 36 spokes and 3 cross pattern and they've been perfect for 7K+ miles. And I'm a clydesdale for sure, ~275lbs.

I agree with something one of the other posters stated, if you don't think a 36 hole, 3 cross pattern will work for you, then go with a 40h or 48h wheel. But with a mountain bike, a 36 h, 3 cross wheel should work. You might also look into finding a deep V rim so that the spokes are shorter.
P. B. Walker is offline  
Old 08-24-04, 07:44 PM
  #14  
The Red Lantern
 
Rev.Chuck's Avatar
 
Join Date: Apr 2003
Location: Raleigh NC
Posts: 5,965
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I have built several trials wheels, 32-3x, with never a problem. My first trials wheel, with ten years on it, shows no issues other than starting to break its alloy nipples at about eight years(since replaced with brass, still original spokes)
__________________
Are you a registered member? Why not? click here to register. Its free, and only takes 27 seconds!
Help out the forums, abide by our community guidelines.

I am in the woods and I have gone crazy.
Rev.Chuck is offline  
Old 08-24-04, 07:53 PM
  #15  
feros ferio
 
John E's Avatar
 
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,764

Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;

Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1384 Post(s)
Liked 1,294 Times in 819 Posts
Hey, Rev. Chuck, is 4X even possible on most 32-hole hubs?

I currently run 32/3x on the Bianchi and 36/3x on everything else, with no complaints or problems.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
John E is offline  
Old 08-24-04, 10:23 PM
  #16  
I drink your MILKSHAKE
 
Raiyn's Avatar
 
Join Date: Jul 2002
Location: St. Petersburg, FL
Posts: 15,061

Bikes: 2003 Specialized Rockhopper FSR Comp, 1999 Specialized Hardrock Comp FS, 1971 Schwinn Varsity

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 3 Times in 3 Posts
Originally Posted by John E
Hey, Rev. Chuck, is 4X even possible on most 32-hole hubs?
.
No It's not divisible by nine.
__________________
Raiyn is offline  
Old 08-25-04, 11:53 AM
  #17  
feros ferio
 
John E's Avatar
 
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,764

Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;

Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1384 Post(s)
Liked 1,294 Times in 819 Posts
Originally Posted by Raiyn
No It's not divisible by nine.
Neither is 40, but 40-4X was standard on the old English 3-speeds. Prime factorization of spoke count is irrelevant here, but the lower the total spoke count, the less radial the spokes become, for a given cross-number and hub flange diameter.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
John E is offline  
Old 08-25-04, 03:22 PM
  #18  
Junior Member
 
Join Date: Jun 2004
Posts: 16
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I don't think the previous poster meant divisible by 9. What he meant to say was the maximum number of crosses for a certain spoke count wheel is determined by the floor of dividing the number of spokes by 9.

48/9 5
40/9 4
36/9 4
32/9 3
28/9 3
24/9 2
etc.

With the right hub there is nothing wrong with 4 cross. If the flange is two small the spoke will travel over the head of the adjacent spoke. As mentioned this makes it harder to lace and can cause fatigue. Most of the Japaneese sport touring bikes I sold in the 1980's had 4x rear and 3x front wheels. Most rear hub flanges are large enough to avoid overlap while most fronts aren't. Certain brands of hubs make the front flange the same size as the rear (e.g. Bullseye, Specialized sealed bearing hubs, Phil Wood). With these hubs you can build the front 4x with no issues and in fact I normally did.

I do remember that you can go too large on the flange for 4x. I know Jobst Brandt cautioned against lacing drum brake and large flange hubs 4x. I don't remember the explination but I do remember him saying it wasn't good. Before I knew better I did build several 4x large flange wheels and I didn't notice any problems with them.
brucejackson is offline  
Old 08-25-04, 03:59 PM
  #19  
Senior Member
 
Retro Grouch's Avatar
 
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225

Bikes: Catrike 559 I own some others but they don't get ridden very much.

Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 642 Times in 363 Posts
I've built some hub brake wheels that had some really big hub flanges. When you try to cross too many spokes, the spokes seem to approach the rim at too much of an angle and eventually break at the nipple. I also rebuilt a rear internal hub geared wheel from a Bike Friday triple that had been replaced by Bike Friday once and rebuilt once by another wheel builder. It looked to me like it suffered from a similar problem due this time to the 20" wheels. I smoothed out the divots in the rim flange spoke holes with a dremel and relaced the hub cross 2 and, last I heard, hasn't broken a spoke since.
Retro Grouch is offline  
Old 08-25-04, 04:17 PM
  #20  
I drink your MILKSHAKE
 
Raiyn's Avatar
 
Join Date: Jul 2002
Location: St. Petersburg, FL
Posts: 15,061

Bikes: 2003 Specialized Rockhopper FSR Comp, 1999 Specialized Hardrock Comp FS, 1971 Schwinn Varsity

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 3 Times in 3 Posts
Originally Posted by brucejackson
I don't think the previous poster meant divisible by 9. What he meant to say was the maximum number of crosses for a certain spoke count wheel is determined by the floor of dividing the number of spokes by 9.

48/9 5
40/9 4
36/9 4
32/9 3
28/9 3
24/9 2
etc.

With the right hub there is nothing wrong with 4 cross. If the flange is two small the spoke will travel over the head of the adjacent spoke. As mentioned this makes it harder to lace and can cause fatigue. Most of the Japaneese sport touring bikes I sold in the 1980's had 4x rear and 3x front wheels. Most rear hub flanges are large enough to avoid overlap while most fronts aren't. Certain brands of hubs make the front flange the same size as the rear (e.g. Bullseye, Specialized sealed bearing hubs, Phil Wood). With these hubs you can build the front 4x with no issues and in fact I normally did.

I do remember that you can go too large on the flange for 4x. I know Jobst Brandt cautioned against lacing drum brake and large flange hubs 4x. I don't remember the explination but I do remember him saying it wasn't good. Before I knew better I did build several 4x large flange wheels and I didn't notice any problems with them.
That's the point I was tying to make.
__________________
Raiyn is offline  
Old 09-30-04, 06:27 AM
  #21  
Newbie
 
Join Date: Sep 2004
Posts: 1
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Hello all,

I am building an electric bike and the 20" rear wheel will be subjected to lots of torque. I have a Surly 36 hole single speed disk hub and had planed on lacing 14G spokes to a bmx rim 4 cross.

After reading your posts I am wondering if I would be better to use a 12G spoke (if I can get them) and lace them in the 3 cross pattern.

Any advice you guys can give me ?

Thanks
i8angus is offline  
Old 09-30-04, 03:20 PM
  #22  
Pro wheelbuilder UK
 
Join Date: Sep 2004
Posts: 127
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by rykoala
Subject says it. When inquiring to the LBS about a stronger wheel, they suggested a 36 spoke wheel laced 4 cross. This being for a 26" rear wheel. According to them the 4 cross pattern is stronger. Any word on this, wheelbuilders among us?
Hi
Go for 3x double-butted. They will be more than strong enough if tensioned properly,evenly and stress- relieved. Use 4x only for hubs with large flange hubs. Using 4x with small-flanged hubs means every spoke would tend to lie on the head of the adjacent spoke. Choose your wheelbulder with care!
wrench is offline  
Old 09-30-04, 05:41 PM
  #23  
legalize bikes
 
Join Date: May 2003
Location: bucks county, PA
Posts: 1,250

Bikes: too damn many

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
rykoala-

what rear hub are you using? hi or lo flange?
legalize_it is offline  
Old 10-01-04, 08:18 AM
  #24  
feros ferio
 
John E's Avatar
 
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,764

Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;

Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1384 Post(s)
Liked 1,294 Times in 819 Posts
Originally Posted by brucejackson
I don't think the previous poster meant divisible by 9. What he meant to say was the maximum number of crosses for a certain spoke count wheel is determined by the floor of dividing the number of spokes by 9.

48/9 5
40/9 4
36/9 4
32/9 3
28/9 3
24/9 2
etc. ...
Thanks for the clarification. Although I have built numerous 0X, 2X, 3X (my favourite by far), and 4X wheels over the years and have read several articles and postings on wheel building, I have to admit I have never before seen your equation, which does look like a very rational (so to speak) guideline.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
John E is offline  
Old 10-01-04, 08:30 AM
  #25  
Senior Member
Thread Starter
 
rykoala's Avatar
 
Join Date: May 2004
Posts: 2,013
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Well I am pretty shocked by the number of responses, and that this thread still lives! Its great info that has come of it. I ended up buying a new wheelset last night. Deore LX hubs on Mavic double wall rims, cant remember the model number. But, I plan on taking the bent wheel from my bike and re-using the hub (older XTR) to build my own wheel for the first time. So this info is VERY valuable to me.
rykoala is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.