Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Using a torquewrench/BBB Torquefix

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Using a torquewrench/BBB Torquefix

Old 09-08-10, 11:35 AM
  #1  
Junior Member
Thread Starter
 
cinecitta's Avatar
 
Join Date: Jul 2009
Location: NY, NY
Posts: 24

Bikes: LOOK, Motobecane

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Using a torquewrench/BBB Torquefix

I just received my torque wrench in the mail. I am familiar with beam style torque wrenches however I've never used this type with a 'rattle mechanism' before. There are very vague instructions that dont have illustrations or explanations so i have a few questions. newbie here so forgive my ignorance. I guess my biggest question is what exactly IS the 'rattle mechanism' followed by these questions in response to BBB's manual:

it states:
1 - "select the correct position of the shifter on the tool head." I have no idea what a shifter is in regards to torque wrenches.


2 - "Fasten the bolts by using the rattle mechanism" what does this mean? there is no illustration.

3 - lock position of the rattle mechanism. again, i don't know what this is.

4 - "unscrew the bolts by using the rattle mechanism." what bolts? i thought i was tightening bolts not unscrewing them...

5 - "When the head clicks through, the set torque is reached. be careful: push gently aginst the back handle with two fingers" I realize there should be an audible click when i reach the torque spec. but i don't understand where it's telling me to "push gently" against after i reach it.

why are these instructions so difficult for me to grasp? I've been wrenching for a while and have just started getting into carbon parts and feel like i should be able to deduce the correct procedures but i think english was not the first language of these writers...

Last edited by cinecitta; 09-08-10 at 11:58 AM.
cinecitta is offline  
Old 09-08-10, 12:00 PM
  #2  
Bianchi Goddess
 
Bianchigirll's Avatar
 
Join Date: Apr 2009
Location: Shady Pines Retirement Fort Wayne, In
Posts: 29,682

Bikes: Too many to list here check my signature.

Mentioned: 190 Post(s)
Tagged: 2 Thread(s)
Quoted: 2896 Post(s)
Liked 2,784 Times in 1,441 Posts
a pic of your wrench would help but it sounds like you have what is refered to 'snap' torque wrench like this. is the head where you put the socket like a regular ratchet?

you simply use the top like anyother ratchet. you are acorrect you should never loosen a bolt/nut with a torque wrench

you dial in the torque with the guage in the handle and then simply tighten until the wrench snaps or clicks.

__________________
One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"

Sugar "Kane" Kowalczyk
Bianchigirll is offline  
Old 09-08-10, 12:03 PM
  #3  
Junior Member
Thread Starter
 
cinecitta's Avatar
 
Join Date: Jul 2009
Location: NY, NY
Posts: 24

Bikes: LOOK, Motobecane

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Yeah, it is like a simple ratchet. however i've been setting the torque to 5nm on the first part that i'm tightening and I feel like I'm tightening it too much and the wrench isn't clicking. maybe i'm unfamiliar with what 5nm feels like?

thought maybe i was setting it up wrong. i twist the handle to reach the desired torque and then just start tightening? i thought maybe it had something to do with 'locking the rattle mechanism' which i'm not sure i understand.
cinecitta is offline  
Old 09-08-10, 12:06 PM
  #4  
Senior Member
 
Join Date: Apr 2008
Location: A Latvian in Seattle
Posts: 1,020
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
I think the "two fingers" part of the instructions refer to how you should apply turning pressure to the handle, so that you can more easily detect the "click". What's the torque range of your wrench? A number of click-style torque wrenches that I've used have only a very faint click when set at the low end of their range.
Mondoman is offline  
Old 09-08-10, 12:14 PM
  #5  
Junior Member
Thread Starter
 
cinecitta's Avatar
 
Join Date: Jul 2009
Location: NY, NY
Posts: 24

Bikes: LOOK, Motobecane

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
torque range is 2-24. will you feel the click or only hear it?
cinecitta is offline  
Old 09-08-10, 12:31 PM
  #6  
Recreational Commuter
 
Join Date: Apr 2006
Location: Central Ohio
Posts: 1,024

Bikes: One brand-less build-up, and a Connondale Synapse Carbon Ultegra Disc. A nicer bike than I need, but it was a good deal, so... ;-)

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 5 Times in 3 Posts
Originally Posted by Mondoman
I think the "two fingers" part of the instructions refer to how you should apply turning pressure to the handle, so that you can more easily detect the "click". What's the torque range of your wrench? A number of click-style torque wrenches that I've used have only a very faint click when set at the low end of their range.
I'd bet $ to doughnuts that the "click" is happening in the first littl ebit of movement, and you're missing it.
Kotts is offline  
Old 09-09-10, 01:38 AM
  #7  
Senior Member
 
Join Date: Aug 2007
Location: Belgium
Posts: 1,032
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 23 Post(s)
Likes: 0
Liked 1 Time in 1 Post
some torque wrenches of this type will not torque past the torque value the user sets it to and will continue to click/slip as the user continues to turn the wrench.

Others will click only once at the value the wrench is set to but then will continue to tighten as if it was not a torque wrench.

It is important to get a feel for how your torque wrench functions prior to using it on critical parts that may be destroyed at relatively low torque values.

Try playing with it on the lug nuts of your car or make something else that is beefier than you will find on a bike.

-j
Greenfieldja is offline  
Old 09-09-10, 10:16 AM
  #8  
Senior Member
 
BCRider's Avatar
 
Join Date: Mar 2008
Location: The 'Wack, BC, Canada
Posts: 5,556

Bikes: Norco (2), Miyata, Canondale, Soma, Redline

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 44 Post(s)
Liked 45 Times in 35 Posts
From your description "rattle" is the rachet mech in the head.

And yeah, sticking the square drive in a vise or on a car lug nut and playing with it first is a darn good idea. The click on my own torque wrench can be quite soft to hear and feel at lower torque ranges and hellishly sharp at the higher end. 5Nm is only 3.7 ft-lbs and very near the low end of your operating range. So it's likely going to be quite a soft click. All the more reason to play with it clamped or onto something that won't move so you can learn to feel the click of the wrench.
BCRider is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
maartendc
Bicycle Mechanics
15
02-09-18 08:38 AM
skids929
General Cycling Discussion
22
04-26-17 01:30 PM
deepakvrao
Bicycle Mechanics
12
04-12-16 06:58 AM
Foilnz
Bicycle Mechanics
9
11-18-14 01:52 PM
sngsndrms
Bicycle Mechanics
59
12-11-09 06:15 AM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.