How to remove frame rust?
#1
Senior Member
Thread Starter
Join Date: Jan 2011
Posts: 84
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
How to remove frame rust?
I have an old single-speed bicycle that has rust on the frame. The rust doesn't look like it ate through the frame. How do i remove rust from the frame?
Thanks.
Thanks.
#2
Senior Member
Join Date: Mar 2008
Posts: 8,688
Mentioned: 46 Post(s)
Tagged: 0 Thread(s)
Quoted: 1074 Post(s)
Liked 295 Times
in
222 Posts
Small spots just scrape down to bare metal with pretty much anything sharp, then seal off with a dab of nail varnish, car touch-up paint, or model builders enamel.
If you have a dremel you can use a small wire wheel or sanding stone as well.
Bigger areas need bigger tools, like wire wheel on angle grinder or electric drill.
If you have a dremel you can use a small wire wheel or sanding stone as well.
Bigger areas need bigger tools, like wire wheel on angle grinder or electric drill.
#8
Senior Member
Join Date: Jun 2009
Location: Montereyish
Posts: 2,306
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
OA-Oxalic Acid, it's the C&Vers best friend. It's commonly referred to as Wood Bleach. You can get it at many hardware and paint stores. It comes in a powdery crystal form that you mix into water and dunk your rusty metal stuff in. In a day or 2, the acid will have eaten the rust. It's amazing stuff. If your bike has significant rust, dunking it in this stuff would be what I'd do. Go to the Classic & Vintage Forum and type in Oxalic Acid in the search engine. You will get great advice about how others have used it, and it's limitations.
#9
Senior Member
Join Date: Jul 2008
Posts: 192
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
On my bianchi frame, the celeste paint and chrome got nicked in some places, and now rust is forming. Very small areas where filing will likely damage surrounding areas. What is the best procedure as to not cause any more damage to the paint? (I have a dremel). I know bianchi makes touch up celeste paint as well.
#10
Senior Member
Join Date: Jan 2004
Posts: 619
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
I suppose you could use the dremel with a wire brush to clean up the rust and then use the touch-up paint after that. I wouldn't trust oxalic acid with the paint.
#12
Senior Member
Only way to do it right is to strip the paint from the entire frame, sand/wire brush the rust then treat the frame with phosphoric acid or oxycilic acid and repaint.
__________________
Il faut de l'audace, encore de l'audace, toujours de l'audace
1980 3Rensho-- 1975 Raleigh Sprite 3spd
1990s Raleigh M20 MTB--2007 Windsor Hour (track)
1988 Ducati 750 F1
Il faut de l'audace, encore de l'audace, toujours de l'audace
1980 3Rensho-- 1975 Raleigh Sprite 3spd
1990s Raleigh M20 MTB--2007 Windsor Hour (track)
1988 Ducati 750 F1
#13
spathfinder34089
Join Date: Jun 2007
Location: Washington State
Posts: 200
Bikes: fuji s12s, Schwiin Le Tour, Puegot mtn. bike, Hiawatha crusier
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I have treated rust on cars and bikes over the years. Currently Napa sells a product called "Rust treatment". Remove as much of the rust you can with sandpaper or a tool that gets it off. Try not to leave scratches. Apply rust treatment and let it dry overnight. If your just touching up bike you can use testors paints and mix paints until you have a match. Apply two or three coats and your done. Its not like bike restoration, but it does preserve the bike from rust decay.