Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Stem instal question

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Stem instal question

Old 12-02-10, 09:26 PM
  #1  
Senior Member
Thread Starter
 
Join Date: Jun 2006
Location: The O.V.
Posts: 121

Bikes: LHT

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Stem instal question

Just got a new stem and the clamp part where it attaches to the fork tube is about 1/4 inch taller than my old one. This has lead to a larger gap between the top of the fork tube and the top of the stem clamp. How big can this gap be and still be safe? The fork tube is about even with the upper bolt on the stem clamp.
jayr is offline  
Old 12-02-10, 09:56 PM
  #2  
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656

Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!

Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times in 741 Posts
What is the steerer material; carbon, steel or Aluminum?

For carbon you want the steerer as fully inside the stem as possible and, preferably sticking out above it so a top spacer is required.

For metal steerers you can be a little more adventurous but I'd want the top bolt of the stem completely below the top of the steerer.

Are there any spacers under the stem you can remove to lower it a bit? If not, a different stem is probably a better idea.
HillRider is offline  
Old 12-02-10, 10:08 PM
  #3  
Senior Member
 
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,544

Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter

Mentioned: 139 Post(s)
Tagged: 1 Thread(s)
Quoted: 5703 Post(s)
Liked 2,432 Times in 1,345 Posts
I'm going to go a bit against the grain here, and will probably be roundly flamed, but I want you to think about this. The old stem worked fine fox a certain amount of time. The new stem has no less actual engagement on the steerer, regardless of what sticks out.

The key thing to consider is where the pinch bolt (or the upper of a pair) is relative to the steerer. If it's well below the end of the steerer you're no worse off than you used to be, so don't sweat it.
__________________
FB
Chain-L site

An ounce of diagnosis is worth a pound of cure.

Just because I'm tired of arguing, doesn't mean you're right.

“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN

WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FBinNY is offline  
Old 12-02-10, 10:17 PM
  #4  
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656

Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!

Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times in 741 Posts
Originally Posted by FBinNY
The key thing to consider is where the pinch bolt (or the upper of a pair) is relative to the steerer. If it's well below the end of the steerer you're no worse off than you used to be, so don't sweat it.
No flames and I agree with your premise, However, the OP said the top of the steerer is about even with the bolt so it sounds like the bolt is not fully supported. Particularly if it's a carbon steerer, I'd be concerned.
HillRider is offline  
Old 12-02-10, 10:34 PM
  #5  
Senior Member
 
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,544

Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter

Mentioned: 139 Post(s)
Tagged: 1 Thread(s)
Quoted: 5703 Post(s)
Liked 2,432 Times in 1,345 Posts
I didn't notice the sentence about the steerer height with reference to the upper pinch bolt. It's less than ideal, but probably still workable, and the problem isn't one of safety. The issue is that overtightening the upper bolt can distort the stem and steerer within.

To avoid problems, extra care should be taken when tightening the upper bolt, and if it were me, I'd shift the clamping force balance toward the lower one, tightening that slightly more than I might otherwise (only if needed to hold properly), and go easier on the upper.

BTW- many carbon fork makers say that this arrangement voids their warranty because it increases the likelihood of splitting the end of the steerer, so if it's a carbon steerer it's something to consider.
__________________
FB
Chain-L site

An ounce of diagnosis is worth a pound of cure.

Just because I'm tired of arguing, doesn't mean you're right.

“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN

WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FBinNY is offline  
Old 12-02-10, 10:48 PM
  #6  
Senior Member
 
Join Date: Feb 2005
Location: Oklahoma
Posts: 9,438

Bikes: Trek 5500, Colnago C-50

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 7 Times in 6 Posts
I would not try that.
Perhaps you can use a stem with one pinch bolt, and place the compression plug centered behind the pinch bolt.
Al1943 is offline  
Old 12-03-10, 05:24 AM
  #7  
DOS
Senior Member
 
DOS's Avatar
 
Join Date: Feb 2008
Location: Arlington, VA USA
Posts: 2,108
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 253 Post(s)
Liked 69 Times in 56 Posts
Is removing or changing size of spacer(s) below the stem clamp not an option to adjust for the taller clamp? Seems like taking out about 1/2cm spacer ought to do the trick. Rule of thumb for the gap is about 3mm; it can be bigger as long and top gap bolt can thread effectively into the star nut. But I agree with other posters that not having steerer tube above the clamp bolt is not a good situation. On a related note, every stem I have the clamp part is 40mm; I thought that was kind of the standard but I guess not.
DOS is offline  
Old 12-03-10, 08:03 AM
  #8  
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656

Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!

Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times in 741 Posts
Originally Posted by DOS
On a related note, every stem I have the clamp part is 40mm; I thought that was kind of the standard but I guess not.
Apparently not. I just measured 6 different threadless stems with two-bolt steerer clamps. Five of these have 40 mm clamp heights. The 6th, an FSA, has a clamp height of only 34 mm.
HillRider is offline  
Old 12-03-10, 10:44 AM
  #9  
Senior Member
Thread Starter
 
Join Date: Jun 2006
Location: The O.V.
Posts: 121

Bikes: LHT

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
It's a carbon fork but the upper tube is alum. It's an 06 Schwinn SSGS flat bar road bike. New stem is a bontrager that I belive is alum. It's this one. https://bontrager.com/model/00744. I can remove a spacer but the reason for the new stem was that I needed to get more height so I went from the stock which I think was a 7 deg to a 25 deg with the same length. I'd like to keep it as high as I can and still be safe. I've got about 5-6 full turns of the top bolt into the star nut. When I look through the back of the stem the upper bolt blocks the top of the fork tube so the top of the tube about right in the middle of that top bolt. I just don't want to pull the bars off or bend up the top of the fork tube or some such thing. It's an XL frame and I'm 6'4 205 if that would make any difference.
jayr is offline  
Old 12-03-10, 11:05 AM
  #10  
Bikaholic
 
blamp28's Avatar
 
Join Date: Dec 2006
Location: Western, Michigan
Posts: 1,461

Bikes: Trek Fuel 90, Giant OCR, Rans Screamer Tandem

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I'm cautious in this type of situation. I would remove enough spacer material so that you can get that upper pinch bolt below the top of the steer tube.
blamp28 is offline  
Old 12-03-10, 11:05 AM
  #11  
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656

Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!

Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times in 741 Posts
I'd remove 3 to 5 mm of spacer. The reduction in bar height will be slight but it's worth it to have the bolt completely below the top of the steerer.
HillRider is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
The_Mickstar
Bicycle Mechanics
1
04-02-17 04:41 PM
ToiletSiphon
Bicycle Mechanics
4
03-08-17 02:31 PM
Gatorfreak
Bicycle Mechanics
19
12-30-14 08:26 PM
robbyville
Road Cycling
27
02-23-13 12:50 PM
krazygl00
Bicycle Mechanics
6
04-23-10 11:54 AM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.