Found a crack in my lug (and frame?) + other questions.
#1
whether man
Thread Starter
Join Date: Sep 2007
Location: San Jose, CA
Posts: 45
Bikes: 197(?) Maserati MT-(?)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Found a crack in my lug (and frame?) + other questions.
I've had this frame for about 2 years now, was storing it on hangers (from the wheels) in the garage. Due to some back problems and space issues, I never got around to working on it until now.
While messing around and tweaking it etc. I found this little crack. I can't tell if it's just the lug or also into the frame. However, I would assume that the frame would have cracked, which would in turn crack the lug (though I have no idea).
Would this be the result of someone trying to force the wrong size headset on or something else? ...I really have no idea and haven't touched the headset
The second part of my question is if this might be a safety issue, yeah it's a tiny crack, but I have no idea.
...As a secondary question, what are peoples thoughts on doing some sort of a clear coat over an old frame? there's a bit of minor surface rusting / chipped paint / and decal pealing going on. Is finishing with a clear coat a no-no for vintage bikes? or is it accepted as long as the paint is original underneath? Although I guess it doesn't matter if the frame is compromised.
While messing around and tweaking it etc. I found this little crack. I can't tell if it's just the lug or also into the frame. However, I would assume that the frame would have cracked, which would in turn crack the lug (though I have no idea).
Would this be the result of someone trying to force the wrong size headset on or something else? ...I really have no idea and haven't touched the headset
The second part of my question is if this might be a safety issue, yeah it's a tiny crack, but I have no idea.
...As a secondary question, what are peoples thoughts on doing some sort of a clear coat over an old frame? there's a bit of minor surface rusting / chipped paint / and decal pealing going on. Is finishing with a clear coat a no-no for vintage bikes? or is it accepted as long as the paint is original underneath? Although I guess it doesn't matter if the frame is compromised.
Last edited by s34s0ns; 04-20-11 at 09:15 PM.
#3
whether man
Thread Starter
Join Date: Sep 2007
Location: San Jose, CA
Posts: 45
Bikes: 197(?) Maserati MT-(?)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#4
Senior Member
Join Date: Jul 2005
Location: Boulder County, CO
Posts: 4,370
Bikes: '80 Masi Gran Criterium, '12 Trek Madone, early '60s Frejus track
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 508 Post(s)
Liked 434 Times
in
331 Posts
That's the clearest example I've seen of a head tube split by a headset race. These are usually caused by the outside diameter of the headset being too large for the inside diameter of the head tube, or the race simply being pressed in improperly.
#5
whether man
Thread Starter
Join Date: Sep 2007
Location: San Jose, CA
Posts: 45
Bikes: 197(?) Maserati MT-(?)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I almost want to just ignore it, but that probably isn't the best idea.
...and I'm trying to stay positive.
#6
Senior Member
Join Date: Jul 2006
Posts: 425
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Someone who does real frame repair and/or framebuilding should have a few options. I could see removing the headset and cups and try to determine the cause. It looks like poor installation and/or improper fitting cups (too large). If the bottom (where the lower cup is ) is fine and usable as is, I could see drilling a hole at the root of the crack (for stress relief, and to terminate the crack and keep it from propagating). Hopefully upon headset removal, the crack will spring closed. For this reason, I'd drill the hole first, because it will be easier to located the end of the crack (root). If it does not spring closed, I'd try to bend it back a little. The inside and outside of the crack is ground a little with a die grinder (think dremel tool) to vee it out for braze repair. The crack is then brazed up, with care taken not to soften the other braze joints. The inside and outside of the repair will then need cleaning and re-shaping, with filing and some work with the die grinder. Then a proper headset installation, first with reaming to get it back to size after the repair, facing for alignment, and then headset installation, making sure to use the correct size. I would think that a properly done braze repair to the crack would be of adequate strength. Alternatively, all the above applied, except for a skilled TIG welder could fix the crack with welding instead of brazing. Tig welding can localize the heat to a high degree. One could also TIG braze.
The other option would be for a framebuilder to replace the head lug. I don't know how often this is done, but it is doable.
Either repair, paint will needed afterwards. I think the former method would require the least amount of intrusion, but I think it is a more unorthodox repair for bicycles. Rather common in other applications. The former method could be done by someone skilled in that type of repair (crack repair), unrelated to bicycles (a welding shop or a machine shop that does job or repair work). I would not expect the latter type of shop to ream and face the head tube after the repair, but leave that to a well equipped bike shop.
I'm assuming you have steel lugs, either investment cast or pressed steel.
Cost to repair? I have no idea. I think the crack repair could be brazed or welded within 2 hours, prep to finish (not reamed or faced).
The other option would be for a framebuilder to replace the head lug. I don't know how often this is done, but it is doable.
Either repair, paint will needed afterwards. I think the former method would require the least amount of intrusion, but I think it is a more unorthodox repair for bicycles. Rather common in other applications. The former method could be done by someone skilled in that type of repair (crack repair), unrelated to bicycles (a welding shop or a machine shop that does job or repair work). I would not expect the latter type of shop to ream and face the head tube after the repair, but leave that to a well equipped bike shop.
I'm assuming you have steel lugs, either investment cast or pressed steel.
Cost to repair? I have no idea. I think the crack repair could be brazed or welded within 2 hours, prep to finish (not reamed or faced).
Last edited by krome; 04-21-11 at 10:35 AM.
#7
whether man
Thread Starter
Join Date: Sep 2007
Location: San Jose, CA
Posts: 45
Bikes: 197(?) Maserati MT-(?)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Awesome information man, that pretty much covers what I was wondering.
Sounds like it's going to need to be done and hopefully the cost won't exceed it's worth. I'd really hate to lose the original paint as well.
Sounds like it's going to need to be done and hopefully the cost won't exceed it's worth. I'd really hate to lose the original paint as well.
#8
Senior Member
Join Date: Aug 2010
Location: Washington
Posts: 472
Bikes: Serotta Davis Phinney, 1992 Serotta T Max,1984 Specialized Allez, Olmo, 1974 Strawberry,Redline bmx, ect.,
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Check the guys at Cycle Art, they can do a full restore and might with your pics. give some advice on the head tube replace but I see $$ signs for this kind of repair. Riding with a loose headset will also do this as well.
#9
whether man
Thread Starter
Join Date: Sep 2007
Location: San Jose, CA
Posts: 45
Bikes: 197(?) Maserati MT-(?)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
...I'm just not sure if I can justify the repair, in terms of $ / losing the original paint / etc.
Disheartening for sure.
#11
whether man
Thread Starter
Join Date: Sep 2007
Location: San Jose, CA
Posts: 45
Bikes: 197(?) Maserati MT-(?)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#12
whether man
Thread Starter
Join Date: Sep 2007
Location: San Jose, CA
Posts: 45
Bikes: 197(?) Maserati MT-(?)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
So, talked to someone about it and the break down is around $300 for a repair on it... mainly structural and around $500 for the repaint / chrome / done 'right'.
If I wait about 3 months he can assist me through the process and teach me at the same time, I'd have to home chrome etc.
this is kind of a horror story.
If I wait about 3 months he can assist me through the process and teach me at the same time, I'd have to home chrome etc.
this is kind of a horror story.
#13
Senior Member
Join Date: Dec 2005
Posts: 7,859
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Hi, well the bike wont disintegrate all of the sudden with a crack like that, but I have seen happening is that the crack will get bigger as the time goes by, since you have not used the bike in a while probably the crack has been always there and never noticed it.
That crack could be because of lack on installation, facing is always good when installing a headset, but you have to add the fact that the bike might be old and the lug simply gave up, the other thing is that many times with series production frames like that one (lug work tells) the tubes in this case the front and the top tube (I believe) are not touching to each other 100% so the lug have to work even more to make it up for the structural fail, If the lug failed the front tube failed as well.
As for repair, u can change the lug or braze the crack from the inside out, sand... and that's it, good as new. The advantage in brazing the crack again (this is done with broken dropouts) is that you wont mess with the angles no more, probably the only thing you will need to do after wards is just face the lug really well. Not a builder but i have seen my master builder done this several times.
Good luck and you have to tell us how to chrome at home THat looks interesting
That crack could be because of lack on installation, facing is always good when installing a headset, but you have to add the fact that the bike might be old and the lug simply gave up, the other thing is that many times with series production frames like that one (lug work tells) the tubes in this case the front and the top tube (I believe) are not touching to each other 100% so the lug have to work even more to make it up for the structural fail, If the lug failed the front tube failed as well.
As for repair, u can change the lug or braze the crack from the inside out, sand... and that's it, good as new. The advantage in brazing the crack again (this is done with broken dropouts) is that you wont mess with the angles no more, probably the only thing you will need to do after wards is just face the lug really well. Not a builder but i have seen my master builder done this several times.
Good luck and you have to tell us how to chrome at home THat looks interesting
#14
Senior Member
Join Date: Mar 2011
Location: Detroit, MI
Posts: 552
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Kind of hard to diagnose what I would do by looking at a picture. But I think I would braze it and give it a try. First I would need to take the headset apart and do some inspecting to see how everything appears structurally. I don't know if that is necessarily the best option. Drilling a stop and a mig tack might work better. I would need to discuss it with a welder.
Of course, if the top cup is not loose in the head tube, riding and seeing if it gets any worse may work too..
Of course, if the top cup is not loose in the head tube, riding and seeing if it gets any worse may work too..
#15
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,274
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 150 Post(s)
Tagged: 1 Thread(s)
Quoted: 6147 Post(s)
Liked 4,092 Times
in
2,325 Posts
Kind of hard to diagnose what I would do by looking at a picture. But I think I would braze it and give it a try. First I would need to take the headset apart and do some inspecting to see how everything appears structurally. I don't know if that is necessarily the best option. Drilling a stop and a mig tack might work better. I would need to discuss it with a welder.
Of course, if the top cup is not loose in the head tube, riding and seeing if it gets any worse may work too..
Of course, if the top cup is not loose in the head tube, riding and seeing if it gets any worse may work too..
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#17
whether man
Thread Starter
Join Date: Sep 2007
Location: San Jose, CA
Posts: 45
Bikes: 197(?) Maserati MT-(?)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
https://bulgier.net/pics/bike/Catalog.../maserati2.jpg
...funny how it doesn't know exactly what kind of steel it's made of.
#18
Senior Member
Join Date: Jul 2006
Posts: 425
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I'm not going to say that brazing the crack is the proper way to repair this frame, but I don't see a crack braze repair as being incompatible with press fitting new cups. Brazing adds material. If it were my bike, I'd most likely braze an additional piece of steel across the crack, to beef up the area. I wouldn't presume to make it look like it was before the crack, just make it safe to ride. It will leave a "scar" if you will.
I was thinking the polished parts were stainless. Being chrome will complicate things (cosmetically).
Last edited by krome; 04-23-11 at 11:33 AM. Reason: clarified "complicate things"
#21
Randomhead
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,363
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,664 Times
in
2,497 Posts
brazing isn't going to make this as strong as it needs to be, and I really wonder about the chroming/painting estimate. It needs a head tube replacement, lug re-welded, and probably a top tube. Brazing temperatures will generate poisonous gases from the chrome; it needs to be removed. I don't think this bike is worth fixing.
#22
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,274
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 150 Post(s)
Tagged: 1 Thread(s)
Quoted: 6147 Post(s)
Liked 4,092 Times
in
2,325 Posts
I haven't done frame repair, but I've done braze and weld repair. Someone who knows how to braze will add material (braze) to the headset tube. This will decrease the inner diameter, done right. After the repair, some metal (braze) will have to be removed (with a reamer) to fit the new cups anyway. If properly done, they will press fit again. Key here is to determine the root cause. Accident? Bad material? Bad cup install? Improper size cups? Determining the cause will influence the remedy. Otherwise I'm in full agreement with what you said.
I'm not going to say that brazing the crack is the proper way to repair this frame, but I don't see a crack braze repair as being incompatible with press fitting new cups. Brazing adds material. If it were my bike, I'd most likely braze an additional piece of steel across the crack, to beef up the area. I wouldn't presume to make it look like it was before the crack, just make it safe to ride. It will leave a "scar" if you will.
I was thinking the polished parts were stainless. Being chrome will complicate things (cosmetically).
I'm not going to say that brazing the crack is the proper way to repair this frame, but I don't see a crack braze repair as being incompatible with press fitting new cups. Brazing adds material. If it were my bike, I'd most likely braze an additional piece of steel across the crack, to beef up the area. I wouldn't presume to make it look like it was before the crack, just make it safe to ride. It will leave a "scar" if you will.
I was thinking the polished parts were stainless. Being chrome will complicate things (cosmetically).
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#23
afraid of whales
Join Date: Apr 2009
Location: Front Range, CO
Posts: 4,306
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 347 Post(s)
Likes: 0
Liked 5 Times
in
5 Posts
OP, it split when the cup was pressed in because the head tube needed reaming. I've seen this failure repaired with silver, a good brazer will limit the chrome discoloration. Brazing always results in dangerous outgasses, that's why you want to use a pro...If you like the frame, the repair I described will allow you to enjoy it for many years, it's a low impact area.