Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Tight external Bottom Bracket

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Tight external Bottom Bracket

Old 05-02-11, 08:26 PM
  #1  
Senior Member
Thread Starter
 
Join Date: Apr 2007
Location: San Diego
Posts: 167
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Tight external Bottom Bracket

I'm building up a bike and I went to put on a Ultegra SM-BB67000 external BB (BC1.37 - the 68mm one) onto a Cannondale Six13 frame. I've seen other people just hand turn the cups on without much resistance until the very end.

I did this, but ended up with considerable resistance (couldn't turn by hand) with about a 2mm gap on both sides.


I don't have the Park BBT-9 tool yet, but I was concerned about not being able to turn all the way by hand. Is the resistance normal?
m015094 is offline  
Old 05-03-11, 12:22 AM
  #2  
Senior Member
 
Join Date: Oct 2007
Location: West Yorkshire, United Kingdom
Posts: 5,773
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 453 Post(s)
Liked 104 Times in 87 Posts
Would suggest getting the BB faced and tapped, this should make it easier to insert the BB, as the threads will be nice and clean.
jimc101 is offline  
Old 05-03-11, 06:41 AM
  #3  
Biking Viking.
 
goatalope's Avatar
 
Join Date: Nov 2007
Location: Camp Hill, PA
Posts: 358

Bikes: '01 Lemond Buenos Aires, '11 Specialized Stumpjumper FSR, 70s Austro Daimler Inter 10, 80s Motobecane Mirage 10 Fixed Gear

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 20 Post(s)
Liked 6 Times in 4 Posts
New or used frame? Was there a BB on it before? Sometimes gunk will build up on the threads beyond the end of the old BB. That could account for the resistance.

Occasionally the threads stop or there's some physical impedance in the bb. However, thats a pretty modern frame with a standard bb, so a physical impedance would be odd.
goatalope is offline  
Old 05-03-11, 07:10 AM
  #4  
Senior Member
Thread Starter
 
Join Date: Apr 2007
Location: San Diego
Posts: 167
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
The frame is used (about 300 miles) and did have a bottom bracket already installed. There was definitely gunk built up but it looked like (and felt like) silver grease.
m015094 is offline  
Old 05-03-11, 10:30 AM
  #5  
Rolling along
 
fas2c's Avatar
 
Join Date: Jul 2007
Location: SE Alabama
Posts: 448
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
It was more than likely anti-seize. I would back the bb out, use some WD40 or light solvent and a toothbrush and rag to clean the threads. Once clean use waterprrof grease or more anti-seize and reinstall the bb. If you still cannot intall the bb correctly have the shop do it as it may need to be faced or threads cut deeper.
fas2c is offline  
Old 05-03-11, 11:46 AM
  #6  
Senior Member
Thread Starter
 
Join Date: Apr 2007
Location: San Diego
Posts: 167
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by fas2c
It was more than likely anti-seize.
Yeah, that's probably it. I noticed the anti-seize on the the threads. I'll wipe it off and give it another shot tonight.
m015094 is offline  
Old 05-03-11, 11:50 AM
  #7  
Senior Member
 
cmill189's Avatar
 
Join Date: Apr 2010
Location: Salt Lake
Posts: 94

Bikes: 2006 Fuji Roubaix SL, 1983 Peugeot P12

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I'm not sure if this is possible, but the plastic sleeve between the cups may not be seated correctly; preventing you from threading the last bit.
cmill189 is offline  
Old 05-06-11, 09:22 AM
  #8  
Senior Member
Thread Starter
 
Join Date: Apr 2007
Location: San Diego
Posts: 167
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
My father always told me to use the right tool for the job and he was right.

So, I got the BBT-9 Park bottom bracket tool yesterday and it solved the problem. Yes, there was anti-seize on the new bottom bracket (which prevented it being turned by hand), but the extra leverage of the correct tool easily turned the BB into the frame.

Thanks for those who replied and let this thread be record to those experiencing problems in the future.
m015094 is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Lawrenceowns
Bicycle Mechanics
9
11-07-15 05:12 PM
Snowden
Bicycle Mechanics
7
10-08-10 08:03 PM
EssEllSee
Singlespeed & Fixed Gear
7
08-15-10 11:01 PM
mosquito
Bicycle Mechanics
7
06-09-10 08:21 PM
jonsan
Bicycle Mechanics
0
02-08-10 06:20 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.