Cycling and bicycle discussion forums. 
   Click here to join our community Log in to access your Control Panel  


Go Back   > >

Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

User Tag List

Reply
 
Thread Tools Search this Thread
Old 02-13-12, 07:56 AM   #1
Post42K
Senior Member
Thread Starter
 
Join Date: Jul 2003
Location: Northern VA
Bikes:
Posts: 185
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
How much WD40 when cleaning sticky Shimano Shifters?

My left-hand shifter was stuck and a few squirts of WD40 did the trick. I also sprayed the right-hand shifter and it made shifting much better but WD40 came out filthy -- almost pure black. I sprayed it again with a good amount but it's still black. My question is, should I keep spraying the WD40 in the right shifter until it drips out clean or just leave it alone?
Post42K is offline   Reply With Quote
Old 02-13-12, 07:59 AM   #2
HillRider 
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Bikes: '''96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '12 Surly Pacer, All are 3x8,9 or 10. It is hilly around here!
Posts: 29,116
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 179 Post(s)
Keep going until it's clean. WD-40 is cheap, brifters are not.
HillRider is offline   Reply With Quote
Old 02-13-12, 09:10 AM   #3
Paul01
Senior Member
 
Paul01's Avatar
 
Join Date: Sep 2010
Location: Tampa Bay, Fl
Bikes: Vitus 979, KHS Montana Comp
Posts: 531
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Keep spraying until it runs clear, and then spray some more. Put plenty of newspaper under the brifters. It's impossible to spray too much WD-40 but that black gunk will stain.
Paul01 is offline   Reply With Quote
Old 02-13-12, 09:44 AM   #4
Post42K
Senior Member
Thread Starter
 
Join Date: Jul 2003
Location: Northern VA
Bikes:
Posts: 185
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Thanks guys. After it runs clear, do you let it air dry for a few days and then re-coat with something like Tri-flow?
Post42K is offline   Reply With Quote
Old 02-13-12, 11:04 AM   #5
Glynis27
Spinning @ 33 RPM
 
Glynis27's Avatar
 
Join Date: Aug 2007
Location: NE Ohio
Bikes: '89 Fuji Saratoga, '97 Schwinn Mesa SS, '07 Felt F1X, '10 Transition TransAM, '11 Soma Analog SS
Posts: 747
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
I generally don't use WD-40 for this and instead use Tri-Flow spray or White Lightning Clean Streak for especially bad shifters. I'll spray into any accessible area until the shifter works freely. Tri-Flow has seemed to work well alone. I assume WD-40 would be enough to keep it working by itself or you could do some Tri-Flow later if you like.
Glynis27 is offline   Reply With Quote
Old 02-13-12, 11:20 AM   #6
HillRider 
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Bikes: '''96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '12 Surly Pacer, All are 3x8,9 or 10. It is hilly around here!
Posts: 29,116
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 179 Post(s)
I'd let the WD-40 evaporate for a few hours then lube the internals wit a lot of Tri-Flow. WD-40 is basically OMS (odorless mineral spirits, a near cousin to kerosene) with a small amount of a special water displacing oil. It's a good cleaner and very light duty lube. I like to lube with something a bit more durable.
HillRider is offline   Reply With Quote
Old 02-13-12, 11:20 AM   #7
bobotech
Senior Member
 
Join Date: Jan 2012
Location: Spokane, WA
Bikes: Specialized Sequoia Elite/Motobecane Fantom Cross Team Ti/'85 Trek 520
Posts: 2,253
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
For fun, I have been rebuilding those old '90s era Shimano shifters at my local bike coop. Almost every one that we have is sticky and barely shifts if at all. The problem is that the grease they used gets hard and sticky. Now I have just sprayed the snot out of them with WD-40 and gotten them freed up but they aren't perfect. The pawls just get gummed up like crazy with the sticky/hard grease and don't flick back like they should.

I will disassemble the shifter starting at the top of it. Quite often the nuts are reverse threads at the top of the shifter. I then place each part in a line on the table. I then use WD40/rubbing alcohol/whatever to clean all the crap out of them. I pay particular attention to the pawls and the pivot points. After i put it back together, they usually work wonderfully and like new. I generally just use a 3-1 oil or PB Blaster lubricant for lube after they are cleaned. I do not use WD40 as the lube.
bobotech is offline   Reply With Quote
Old 02-13-12, 11:53 AM   #8
fietsbob 
coprolite
 
fietsbob's Avatar
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Bikes: 7
Posts: 22,134
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 1123 Post(s)
WD is mostly solvents, you can also use kerosene , flush out the crud.
then lubricate with something else, as suggested.
fietsbob is offline   Reply With Quote
Old 02-13-12, 12:10 PM   #9
HillRider 
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Bikes: '''96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '12 Surly Pacer, All are 3x8,9 or 10. It is hilly around here!
Posts: 29,116
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 179 Post(s)
A more effective, if laborious and equipment intensive, way to clean a gummed up STI brifter is to remove the cables and push out the brake lever pivot pin. The pivot pin has a small set screw underneath that has to be removed and a small return spring so pay attention to how it's placed before you remove anything. Once the pin is out, the entire shifter/brake lever assembly can be removed from the body. Place this assembly in a jar full of OMS or Kerosene and either shake it frequently or, better yet, agitate the solvent continuously. A lab magnetic stirrer is great for this or, ideally, an ultrasonic cleaner bath. Let it soak for several hours with frequent shaking or agitation. You will be amazed at what comes out in the solvent. If it is really dirty, change the solvent a time or two.

After several hours remove the shift/brake lever assembly and drain and shake off the solvent. Let it dry for a few hours and lube copiously with Tri-Flow or similar oil. Then reassemble and reconnect the cables.
HillRider is offline   Reply With Quote
Old 02-13-12, 04:54 PM   #10
Nick Bain
Senior Member
 
Nick Bain's Avatar
 
Join Date: May 2010
Location: Driftless
Bikes: Caad8, Tarmac, Raleigh M80, Mukluk 3, Custom chopper.
Posts: 1,718
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
TRI-flow kicks ass! cleans and lubes. fixed both my deore shifters
Nick Bain is offline   Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -6. The time now is 07:20 PM.