Bike Forums

Bike Forums (https://www.bikeforums.net/forum.php)
-   Bicycle Mechanics (https://www.bikeforums.net/bicycle-mechanics/)
-   -   700x28/32C tube (https://www.bikeforums.net/bicycle-mechanics/799416-700x28-32c-tube.html)

Atomic Taco 02-17-12 10:22 PM

700x28/32C tube
 
I have 700x28C tires (and wheels too I suppose). I bought a Kenda tube that's marked 700X28/32C. It's too big. What's up with this size?



On an unrelated note: I have one brand new 700x28/32C tube for sale.

ThermionicScott 02-17-12 10:30 PM

It's not too big. Inflate the tube a little before putting it in the tire, and it'll stay out of the way.

Atomic Taco 02-17-12 10:40 PM


Originally Posted by ThermionicScott (Post 13866757)
It's not too big. Inflate the tube a little before putting it in the tire, and it'll stay out of the way.

Did that; once on the rim I have about 3 inches of space on the opposite side.

ThermionicScott 02-17-12 10:53 PM

That's fine... once you've gotten both beads of the tire on, it'll figure out where to go.

Burton 02-17-12 11:26 PM

Did those tires origonaly come off those same rims?

Jeff Wills 02-17-12 11:54 PM

It's the tire that maintains the shape- the tube just seals in the air.

Put only a little bit of air in the tube, not so much that it starts to stretch out. Place it in the tire, mount the tire on the rim. Be careful not to pinch the tube between the rim and tire. Once both beads of the tire on the rim, inflate it to about 15psi. Check all the way around the wheel to check that the tire is mounted evenly on the rim- there's a line molded into the tire that should sit on top of the rim. If it's not even, deflate, pull out any low spots, check to see that the tube isn't caught under high spots, and start pumping it up again. Check again when you get to 30psi- then 60 psi.

Atomic Taco 02-17-12 11:56 PM


Originally Posted by Burton (Post 13866890)
Did those tires origonaly come off those same rims?

I think so. I bought the bike used and the models of each match the spec sheet for the (now discontinued) bike.

Originally Posted by ThermionicScott (Post 13866822)
That's fine... once you've gotten both beads of the tire on, it'll figure out where to go.

Well duh! Should've thought of that--put the tire where it's going to go. This ain't rim tape.

It's working good.

Jeff Wills 02-17-12 11:57 PM


Originally Posted by Atomic Taco (Post 13866965)
It's working good.

But your grammar ain't.

HillRider 02-18-12 08:33 AM

I bought a pair of Nashbar's "Comfort" tires for my rain bike a while ago. They were listed as 700x32 so I also bought some 700x 28-32 tubes at the same time. Well, the tires actually measure 26 mm and the tubes turn out to be a stuff-fit and a pain to install. They work but are larger then needed and require a lot of care to prevent the excess rubber from being caught between the bead and the inside of the rim. It's fussy enough installing them in my workshop but it was a lot more fun repairing a roadside flat with one of them in a cold rain a few months ago. When these are used up, their replacements will be smaller.


All times are GMT -6. The time now is 03:09 PM.


Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.