Help needed for removing handlebar stem!
#1
Junior Member
Thread Starter
Join Date: Sep 2012
Posts: 12
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Help needed for removing handlebar stem!
So I recently bought this Cannondale multisport 500, the original owner raised the stem way too high for my taste. As seen, I've already removed the screw at the top of the stem. But when i try to push down or pull up the stem, it won't budge. I think that black piece is an extender? I need help on removing that. I think it might be rusted on the inside but I'm not so sure. Anyone with any opinion, feel free to give me some heads up! Thanks.
#2
Senior Member
Join Date: Mar 2008
Location: Costa Mesa CA
Posts: 2,636
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 5 Post(s)
Likes: 0
Liked 11 Times
in
10 Posts
Thread the bolt back in a bit. Give it a tap straight down. There's a wedge in the stem that can get stuck. This'll loosen it. If it still doesn't give, soak it with PB Blaster or WD-40 over night. The last step is to butt a piece of wood under the handlebar clamp and smack it with a hammer.
#3
Senior Member
I believe this is a two step process. Do as Flying Merkel stated above to remove the stem then look down the extender and I believe you'll find another bolt that is holding the extender in place. Remove is in the same manner as the stem and you should be able to remove the extender.
#5
Junior Member
Thread Starter
Join Date: Sep 2012
Posts: 12
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I've tried to tap it straight down. Hmm, where exactly should i apply the WD-40? And yeah, the black thing seems like an extender. If I were to remove the stem, the extender will come out with it right?
#6
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,792
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5826 Post(s)
Liked 2,660 Times
in
1,478 Posts
If it's stuck, use "kroil" or some other "seized bolt loosener oil" between the stem and sleeve, then again if needed between the sleeve and fork.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
#7
Junior Member
Thread Starter
Join Date: Sep 2012
Posts: 12
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Alright i finally got it guys! thanks for the help! I just needed to pop the top screw real hard and it slide out easily. (:
This is how it looks now! Thanks a bunch guys, really appreciate the tips.
This is how it looks now! Thanks a bunch guys, really appreciate the tips.
Last edited by mikeazn3k; 09-26-12 at 11:31 PM.
#10
Senior Member
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,319
Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 1438 Post(s)
Liked 1,092 Times
in
723 Posts
Lowering your bars has had the side effect of making your shift and brake cables too long. Your rear brake cable housing is clearly drooping down too far in the photo. You should consider shortening them for best braking and shifting performance.
#11
Junior Member
Thread Starter
Join Date: Sep 2012
Posts: 12
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Haha! thanks rogerstg.