Removing 3-speed rear wheel
#1
Junior Member
Thread Starter
Join Date: Dec 2006
Posts: 9
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Removing 3-speed rear wheel
Hello everyone,
I aquired a Columbia Sports III recently. Needs tubes and tires. How do I remove the rear wheel without disturbing the shifter cable? This is a SA-AW hub. I see how the cable can be separated, but how do I keep the hub in adjustment, or do I have to adjust the gears after installing the wheel? I realize this is old hat to most of you, but I would appreciate any advise.
Thanks, Bob
I aquired a Columbia Sports III recently. Needs tubes and tires. How do I remove the rear wheel without disturbing the shifter cable? This is a SA-AW hub. I see how the cable can be separated, but how do I keep the hub in adjustment, or do I have to adjust the gears after installing the wheel? I realize this is old hat to most of you, but I would appreciate any advise.
Thanks, Bob
#2
Senior Member
Join Date: Dec 2005
Posts: 17,158
Mentioned: 481 Post(s)
Tagged: 0 Thread(s)
Quoted: 3810 Post(s)
Liked 6,699 Times
in
2,611 Posts
Bob, usually there's a threaded piece that stays on the indicator (the small chain and rod part that screws into the SA hub) when you unscrew the gear cable end. That marks how far to screw that cable on the next time you hook it up. If you don't have one of those, just mark with a piece of masking tape how far the cable end is threaded on to the indicator.
Neal
Neal
#3
Elitest Murray Owner
Join Date: Apr 2006
Posts: 2,657
Bikes: 1972 Columbia Tourist Expert III, Columbia Roadster
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 3 Times
in
2 Posts
Just disconnect the the cable. You'd have to readjust it anyway when you put the wheel back on, even if you left it connected (because you're not likely to put the wheel back in exactly the same place in the dropouts as it was before, so it's adjustment will change anyway)
#4
Membership Not Required
Join Date: Jan 2005
Location: On the road-USA
Posts: 16,855
Bikes: Giant Excursion, Raleigh Sports, Raleigh R.S.W. Compact, Motobecane? and about 20 more! OMG
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 70 Post(s)
Likes: 0
Liked 15 Times
in
14 Posts
You will have to readjust unless you get lucky and get it back in exactly the same place. Adjustment is pretty straight forward. Use Sheldon Brown's directions.
Aaron
Aaron
__________________
Webshots is bailing out, if you find any of my posts with corrupt picture files and want to see them corrected please let me know. :(
ISO: A late 1980's Giant Iguana MTB frameset (or complete bike) 23" Red with yellow graphics.
"Cycling should be a way of life, not a hobby.
RIDE, YOU FOOL, RIDE!"_Nicodemus
"Steel: nearly a thousand years of metallurgical development
Aluminum: barely a hundred
Which one would you rather have under your butt at 30mph?"_krazygluon
Webshots is bailing out, if you find any of my posts with corrupt picture files and want to see them corrected please let me know. :(
ISO: A late 1980's Giant Iguana MTB frameset (or complete bike) 23" Red with yellow graphics.
"Cycling should be a way of life, not a hobby.
RIDE, YOU FOOL, RIDE!"_Nicodemus
"Steel: nearly a thousand years of metallurgical development
Aluminum: barely a hundred
Which one would you rather have under your butt at 30mph?"_krazygluon
#5
Junior Member
Thread Starter
Join Date: Dec 2006
Posts: 9
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Removing 3-speed wheel.
Hello everyone,
How do I remove the rear wheel on a Columbia Sports III without disturbing the gear adjustment? Could someone walk me through it in simple terms? Just the basics. Bike needs tubes and tires. That part is no problem. I just need help with the hub.
Many thanks, Bob
How do I remove the rear wheel on a Columbia Sports III without disturbing the gear adjustment? Could someone walk me through it in simple terms? Just the basics. Bike needs tubes and tires. That part is no problem. I just need help with the hub.
Many thanks, Bob
#6
Senior Member
Join Date: Nov 2005
Location: NW Ohio
Posts: 3,419
Bikes: 1984 Miyata 310, 1986 Schwinn Sierra, 2011 Jamis Quest, 1980 Peugeot TH8 Tandem, 1992 Performance Parabola, 1987 Ross Mt. Hood, 1988 Schwinn LeTour, 1988 Trek 400T, 1981 Fuji S12-S LTD, 197? FW Evans
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 531 Post(s)
Liked 1,005 Times
in
514 Posts
It isn't very difficult to adjust the shifting after removing the cable from the rear hub. There should be a small turnbuckle right at the end of the cable, just unscrew it to unhook the cable. Then loosen the axle nuts and take the rear wheel off. When you are done, put the wheel back on and reconnect the cable. To adjust, if you have a Sturmey-Archer hub, put the shifter in 2 or N and adjust the cable until the shoulder of the indicator rod is just visible in the cutout in the axle nut. If you have a Shimano, put the shifter in 2 and adust the cable until the N is centered in the window on the end of the axle. In both cases, the cable should have no tension when in high gear, and there should be very little additional travel when in low.