Stuck Campy crank
#1
Prodigal road guy
Thread Starter
Join Date: Jul 2006
Location: Eugene. Oregon
Posts: 416
Bikes: '72 Bob Jackson; '82 Austro-Daimler Starleicht; '85 Scapin; '80 Peugeot PKN-10; '81 Trek 610; '87 Hunter Corsa; '72 Italvega and '75 Motobecane Grand Jubillee frames built into freewheel singlespeeds.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Stuck Campy crank
I have a '78 Raleigh Competition GS with the Campy Nuovo Gran Sport drive train. The drive side crank just won't budge off of the spindle. Tips to loosen it up?
#3
Prodigal road guy
Thread Starter
Join Date: Jul 2006
Location: Eugene. Oregon
Posts: 416
Bikes: '72 Bob Jackson; '82 Austro-Daimler Starleicht; '85 Scapin; '80 Peugeot PKN-10; '81 Trek 610; '87 Hunter Corsa; '72 Italvega and '75 Motobecane Grand Jubillee frames built into freewheel singlespeeds.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Yes, I'm using a crank puller ... I'd have permanently bloodied knuckles and a lot of really old bottom bracket grease in all of my bikes if I didn't.
One of the problems is that when it's tightened all the way, the handle on my puller is at about 5 o'clock from the crank, so it's really hard to get good leverage using just my hands.
One of the problems is that when it's tightened all the way, the handle on my puller is at about 5 o'clock from the crank, so it's really hard to get good leverage using just my hands.
#4
Senior Member
Join Date: Jul 2004
Location: Yukon, Canada
Posts: 8,759
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 113 Post(s)
Likes: 0
Liked 16 Times
in
14 Posts
cheater bar time.
__________________
1 Super Record bike, 1 Nuovo Record bike, 1 Pista, 1 Road, 1 Cyclocross/Allrounder, 1 MTB, 1 Touring, 1 Fixed gear
1 Super Record bike, 1 Nuovo Record bike, 1 Pista, 1 Road, 1 Cyclocross/Allrounder, 1 MTB, 1 Touring, 1 Fixed gear
#6
hunter, gatherer
Join Date: Feb 2005
Posts: 1,183
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
if it's really that tight just go slow and use some sort of penetrant perhaps..
i've never heard of a crank being stuck such that the puller won't turn
usually you just end up stripping the extractor threads !
(make sure you lightly greased them and got the extractor threaded in all the way nice and tight)
i've never heard of a crank being stuck such that the puller won't turn
usually you just end up stripping the extractor threads !
(make sure you lightly greased them and got the extractor threaded in all the way nice and tight)
#7
Senior Member
Join Date: Sep 2005
Posts: 2,116
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 21 Post(s)
Likes: 0
Liked 13 Times
in
10 Posts
Worst case scenario cute the SOB off and start fresh. In some cases it is worth it to strip the crank extractor tool if the threads are already too boogered up.
#8
Stop reading my posts!
Join Date: Sep 2004
Posts: 12,584
Mentioned: 90 Post(s)
Tagged: 0 Thread(s)
Quoted: 1444 Post(s)
Liked 1,063 Times
in
788 Posts
Yes, use a penetrant (a good one, not WD40) and try a little heat (propane torch, *carefully*) and smack the crank a bit with a soft mallet (hardwood, copper, deadblow) to set up some shock waves. Do as Coelcanth says: clean threads and nice and tight (but not TOO tight) when you screw that extractor in...I usually have best luck with the Park tool.
#9
Junior Member
Join Date: Oct 2007
Posts: 8
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
You DID take the washer out...?
Not that I have ever tried to pull a crank with the washer still inserted, but I have heard tell that other people have done so.
-Clyde
Not that I have ever tried to pull a crank with the washer still inserted, but I have heard tell that other people have done so.
-Clyde
#12
Senior Member
Join Date: Mar 2005
Location: Pinole, CA, USA
Posts: 17,392
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 443 Post(s)
Likes: 0
Liked 27 Times
in
25 Posts
It was a Stronglight puller. The washer got stuck on it and I destroyed the puller's threads prying off the washer. I wish I could say it happened long ago when I was new at this stuff, but I can't.
#13
Senior Member
Join Date: Mar 2006
Posts: 2,754
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 83 Post(s)
Likes: 0
Liked 13 Times
in
11 Posts
Exactly. The only time I've seen a Campy crank not come off using a proper puller is when the washer was left on. I've never had to do this myself as I was lucky enough to see a friend break the threads out of crank doing this. I'd bet money it's the OP's problem.
#14
www.theheadbadge.com
Join Date: Sep 2005
Location: Southern Florida
Posts: 28,513
Bikes: https://www.theheadbadge.com
Mentioned: 124 Post(s)
Tagged: 0 Thread(s)
Quoted: 2422 Post(s)
Liked 4,395 Times
in
2,092 Posts
#15
Nut
Join Date: Apr 2005
Location: Tallahassle, FL
Posts: 697
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
pound the puller with a mallet, but make sure is all the way tight first.
pull the bottom bracket from the frame with the crank stuck on. heat it with a torch at the join and then hammer the bb spindle out. put the crank arm somewhere stable like in a vice to make this easier. it can also be done on the kitchen stove in a pinch if the wife is still at work.
pull the bottom bracket from the frame with the crank stuck on. heat it with a torch at the join and then hammer the bb spindle out. put the crank arm somewhere stable like in a vice to make this easier. it can also be done on the kitchen stove in a pinch if the wife is still at work.