ISO: A single ferrule for Universal Mod. 77 brake lever (photo below). And some Universal brake hoods. I am hoping Cane Creek will work for the latter (posted an inquiry here), but the former ... I am at your mercy oh hoarders!
Have: What are you looking for? I have stuff! I have a firstborn!
-Sugino Mighty crankset, vgc, 170mm, OE drilled rings, OE chainring bolts…very nice (also have the UN-54/115mm BB I used).
-Simplex Retrofriction shifters, mounted on clamp-on tube mount.
-1st Gen Suntour Cyclone GT RD
-1st Gen Suntour Cyclone FD
-Shimano 600 Arabesque FD
-Campagnolo Record 8s FD
-Campagnolo Athena 8s FD
-Campagnolo Record 10s FD, alloy.
-Campagnolo Daytona brakeset, needs pad holders.
-Campagnolo Centaur 10s DP brakeset…excellent condition
-Campagnolo Centaur 10s RD VGC
-Campagnolo Veloce, all alloy, 10s Ergos VGC (including Hudz "gum" hoods)
-Regal saddle, white, small corner scuffs, copper rails and rivets.
-Gipiemme CronoSprint seatpost, 27.0
-Athena 8s crankset VGC, typical light arm scratching
-'89 Pinarello Treviso frameset, nice paint, fresh decals, Shimano 600 headset, 57cm.
-Dura Ace 7400 stem, excellent condition, cap is present, 100mm
-Cinelli XA stem, excellent, 90mm
-Single/Fixed Wheelset. 700c
-Campy Record OS 10s rear hub, 32H (or 28H as well)
-Campagnolo 11s bits
-Speedplay Zero pedals/cleats (new or lightly used cleats only)
-Fizik Aliantes/Spec Romin Evos/Spec Phenoms
-Quality 25c tubs (ie Vittoria Corsa CX)
-Deda Zero 100 DMP stems, 110 or 120, 86deg.
-Mark in St. Louis
ISO: Campagnolo Record 144 bcd drive-side crankarm. Can be in rough shape cosmetically of functional. Would consider any length.
Have: Various items of value.
I got you covered on that Campy bit as well! :thumb: cudak888 gave me a couple a few years ago and it will go in the package with the TA triplizer. :D
Amazing! Thanks, Bob.
Originally Posted by pastorbobnlnh
ISO: Do you have a Park Tools Spoke Tension Meter (TM-1) collecting dust? If so, send me a PM. Thanks.
Never mind! But remind me sometime, we need to discuss how to change the mounting bolt on a dual pivot brake. I just swapped the bolt from a Shimano 1055 caliper with one from a Tektro R569, and (despite all my expectations) it worked fine. But where did these four tiny little ball bearings come from?
On topic, though... Anyone have a trashed Campy Nuovo Record rear derailleur? If so, I might want some of it... The big pieces, not the little ones.
Looking for a 1970s era Cannondale saddle bag.
Like this, preferably red or blue, and I hope in less faded condition!
I have a nice blue bag, looking for a good home. Single owner - me. It's darker than the picture because of the flash. Yours for the cost of shipping if that's ok with you. PM me to work out the details.
Originally Posted by DMNHCAGrandPrix
rhm, do I understand you correctly, that you could use the Shimano calipers you have but you prefer Tektro? Are you building a Shimano-free bike or something?
No, you don't get it, which is not your fault since I have explained nothing.
Originally Posted by noglider
The problem was (note: past tense) I had a set of tektro long reach, recessed mount, brakes; and I wanted the same, nutted. And I had (yes, past tense) Shimano 1055 short reach calipers, nutted, but wanted recessed ones.
I seem to have solved the problems, by switching one tektro bolt for one shimano one, and all went well... But I have four tiny ball bearings that I don't know where they came from.
That's interesting, because I've recently been finding small bearings all over the floor. Headset size?
Originally Posted by rhm
No, much smaller. I haven't measured them but I'm guessing about 1.5 mm. Really little.
Originally Posted by seedsbelize
Check the action on the 105 quick releases. Especially the rear one.
I've a dim memory (always) of encountering these, as I've swapped bolts several times, from tricolor up through Tektro R741.
Originally Posted by rhm
I'll see if I can remember.
I'm hesitant to even write these words, but here goes... I'm in search of a Huffy!
Yes, I just said that. Actually, in all seriousness, I'm looking for a quirky next project and I'd love to find one of the early 60's Carlton made Huffies (Road bike style-- not the three speeds) if there are any out there going ignored or unloved. I've seen lots of model name out there for that era: constellation, corsair, centurion, catalina. I'd be interested in either a frame set or a full bike. I know I could just search for a Carlton model from then, but looking for the fun factor of the Huffy branding. Any out there?
@rhm Might be able to help you with the NR parts. PM me with which parts.
I am looking for any parts for Suntour ratcheting Barcons. Heavy emphasis on the bolt and nuts.
I still have a few of these: http://www.bikeforums.net/classic-vi...l#post16370471
Originally Posted by dweenk
Want: 140mm (+-5) quill stem
Have: Normal sized stems
SOLD SOLD SOLD HAVE: 1953-ish? NOS GB SuperHoods in white. Full hoods, still in orig plastic wrap, never opened, still supple, like new condition. Can be cut with a razor to make half hoods if half hoods are what you want, I personally wouldn't do it as hens teeth would be an easier find than these GB hoods.
WANT: I can use a set of Maxxis Hookworm 26x2.5", 1950s balloon tire bike stuff, nothing in particular, tell me what you got. :)
You can PM me with other offers. Thanks.
Bicycles: Road Bikes Classifieds for Utah, Idaho, and Wyoming | ksl.com not into vintage bikes and not sure what your looking for but came across this.
Originally Posted by mnmkpedals
Wow, sincere thank you for pointing that out. I got excited, but yeah, looks like a slightly newer one, not Raleigh made as the seller says, and seems to be from when, well... when yeah, Huffy made their own cheap bikes. Non lugged, not even cottered crank.
Originally Posted by vandutch
But honestly, thanks a ton for pointing it out. Much appreciate the kindness with the lead!
^ no prob....sorry it wasn't what it said.
Rudy, check the plastic washer. There are tiny bearings inside the washer on the BR-1055 bolt assembly.
Originally Posted by rhm
Shimano BR-1055 Rear Pivot Bolt Assembly - £5.99