Originally Posted by 67tony
(Post 17842812)
I'd like a brake cable hanger thinner than this one.
(I'd rather not re-install the one that's integrated with the reflector.) Anyone have one, or know of a source for one? Your LBS should have one, call around. |
I have one that I made from a brake lever. It clamps to the 22.2 mm section of stem above the headset, so isn't involved with the headset at all. You can make your own, or pm me and I'll send you mine. I'm not using it anymore. It's not even very ugly! :lol:
|
Originally Posted by rhm
(Post 17843062)
I have one that I made from a brake lever. It clamps to the 22.2 mm section of stem above the headset, so isn't involved with the headset at all. You can make your own, or pm me and I'll send you mine. I'm not using it anymore. It's not even very ugly! :lol:
|
YES, +1 ^ I like it, but would like to see a pic, too...when you get around to it.
|
Looking to turn an old road frame into an upright errand bike.
ISO: Technomic stem Deore 7sp thumbies Alloy 1" threaded headset (preferably black) 43t or 44t chainring for early 80s SR crank (preferably black) HAVE: minty red Bluemels shorty fenders circa 1980 NOS Campagnolo Olympus Cantilever F&R set champagne Shimano EX pedals Lots of other detritus, just ask.... |
Originally Posted by Cerrig
(Post 17850957)
43t or 44t chainring for early 80s SR crank (preferably black)
|
Sorry, I was in too much of a hurry, I apologize. They are Sakae Ringo, 5 arm road double cranks with a 118 bcd.
|
ISO American size (21.15 mm) quill stem for an old Ross ladies bicycle. I don't care about size or condition as long as it's functional.
|
Originally Posted by b dub
(Post 17851221)
ISO American size (21.15 mm) quill stem for an old Ross ladies bicycle. I don't care about size or condition as long as it's functional.
|
Originally Posted by Little Darwin
(Post 17851251)
I will be looking for something else tomorrow in my bike room, so I will see what I have. I suspect I have a few laying around, probably steel but I may have an aluminum one as well. If I find something, I'll contact you through PM, but you can probably have it for cost of shipping. The small flat rate Priority Mail box seems to work well for things like this.
|
Originally Posted by Cerrig
(Post 17851169)
Sorry, I was in too much of a hurry, I apologize. They are Sakae Ringo, 5 arm road double cranks with a 118 bcd.
|
ISO:
1. short/shallow drop bar similar to Soma Hwy One or VO Dajia, 26.0 clamp and 40-42cm wide (25.8 clamp even better) 2. short quill stem 25.4 clamp x 1-1/8 steer tube Can trade: A nice used Technomic 25.4 stem ( @Cerrig ) other stems not as nice but still usable: Ritchey Force (by HL, not Nitto) ~130mm CrMo 25.4 clamp 22.2 quill riser stem black HL ~110mm CrMo 25.4 clamp 22.2 quill riser stem black (from Bridgestone X0-2) HL 100mm CrMo 25.4 clamp 22.2 quill 73 deg stem chrome (from '95 Randonee) some bars in fair/usable shape... Scott Drop-In bars 26.0 (measures 26.2) 40cm wide gray HL alum round drop bars 25.4 x 38 wide silver Trek alum round drop bars 26.0 x 42 wide single cable grooves silver SR randonneur bars 25.4 x 42 wide A near-new woman's saddle, Serfas Rx Portland and Seattle both local for me |
ISO:
Clamp + Bolt/Nut for early STI Shifter For Trade: Just ask, my parts bin runneth over. |
ISO: Looking for original Schwinn 700c fork for late 80s 25" Tempo/Prelude.
For Trade: Lots of stuff laying around |
ISO: Looking for a mid-70s weight weenie freewheel. Alloy (or even titanium if a reasonable trade can be made), and ideally with a low gear in the 24t-26t range. Something like a Zeus 2000, Maillard Course 700 (alloy cogs), Regina Titanio, Suntour Microlite, etc. but open to other options. English threading preferred, might consider Italian. Used okay, and willing to overhaul innards on my end, but should have some life left on the cogs.
Have: A good amount of this & that. What do you need? |
Iso: campy groupset. why not? its worth a try!
|
Originally Posted by gaucho777
(Post 17859332)
ISO: Looking for a mid-70s weight weenie freewheel. Alloy (or even titanium if a reasonable trade can be made), and ideally with a low gear in the 24t-26t range.
|
Originally Posted by JohnDThompson
(Post 17859671)
I have a BSC thread Zeus freewheel I'd consider trading for a set of high-flange Zeus or Campy track hubs.
|
Originally Posted by Seabass_First
(Post 17859382)
Iso: campy groupset. why not? its worth a try!
|
Originally Posted by Seabass_First
(Post 17859382)
Iso: campy groupset. why not? its worth a try!
|
Originally Posted by icepick_trotsky
(Post 17861469)
Vintage? Ergo? Vintage ergo?
|
Originally Posted by Seabass_First
(Post 17862441)
Im not picky. pretty much anything OTHER than triumph(have one)... also it doesn't have to be complete, could be a "mini group" with just cranks & derailleurs
|
Hello,
ISO In mild desperate need for a seat tube Reynolds 501 decal. About ready to roll my 89 Gazelle Race out for the summer season and don't have this important piece in place yet. Any one with one out there ? have Many things... Thanks ! |
Your fastest bet is probably going to be velocals. I've had good luck with Cyclomondo from down under. Either one could probably hook you up with just the one decal.
|
ISO: Campy early bar end shifters.
135 or 140 Cinelli quill stem Trade offerings: Suntour bar ends shifters 2 Suntour Cyclone long cage rear derailleurs, early Exage Sport RD, FD, brakes/levers 2 3TTT quill stems, both 120mm with 25.4 or 26mm clamps, I think Campy Victory crankset w/rings Campy Italian threaded bottom 3 piece BB. Need to check the size, hollow spindle Other stuff I can't recall at the moment |
All times are GMT -6. The time now is 01:21 AM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.